2009 FIAT PUNTO EVO wheel

149
STARTING PROCEDURE FOR PETROL
VERSIONS
Proceed as follows:
❒ensure that the handbrake is on;
❒put the gear lever into neutral;
❒fully depress the clutch pedal without touching the ac-
celerator;
❒turn the ignition key to AVV and let it go the moment
the engine starts.
If the engine does not start at the first attempt, return
the ignition key to STOP before repeating the procedure.
STARTING THE ENGINE
The car is fitted with an electronic engine lock device: if
the engine fails to start, see the paragraph on “The Fiat
CODE system” in the “Dashboard and controls” section.
The engine may be noisier during the first few seconds of
operation, particularly after a long period of inactivity. This
is a feature of hydraulic tappets, the timing system cho-
sen to reduce the number of servicing interventions, and
effects neither functionality nor reliability.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
STARTING AND DRIVING
It is dangerous to let the engine run in en-
closed spaces. The engine consumes oxy-
gen and produces carbon dioxide, carbon monox-
ide and other toxic gases.
WARNING
In the first period of use, we recommend
that you do not demand maximum perfor-
mance from the car (e.g. excessive accel-
eration, extended travel at maximum revs, heavy
braking etc.).
With the engine off, do not leave the
key in the ignition to prevent draining the
battery.
Remember that the brake booster and
power steering are not operational until
the engine has been started, therefore you need
to apply much more force than usual to the brake
pedal and steering wheel.
WARNING
149-160 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 149

151
STOPPING THE ENGINE
Turn the ignition key to STOP while the engine is idling.
IMPORTANT After a long drive, you should allow the en-
gine to “catch its breath” before turning it off by letting it
idle to allow the temperature in the engine compartment
to fall. WARMING UP THE ENGINE AFTER IT HAS
JUST STARTED (petrol and diesel versions)
Proceed as follows:
❒drive off slowly at medium revs, and accelerate
smoothly;
❒do not demand maximum performance for the first few
kilometres. Wait until the engine coolant gauge starts
moving.
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTSRemember that the brake booster and pow-
er steering are not operational until the en-
gine has been started, so you need to apply
much more force than usual to the brake pedal and
steering wheel.
Never jump start the engine by pushing,
towing or driving downhill. This could cause
fuel to flow into the catalytic converter and
damage it beyond repair.
A quick burst on the accelerator before
turning off the engine serves absolutely no
practical purpose; it wastes fuel and is es-
pecially damaging to turbocharged engines.
149-160 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 151

152
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
F0U0129mfig. 147
HANDBRAKE fig. 147
The handbrake lever is located to the left side of the dri-
ver’s seat. Pull the lever upwards to operate the handbrake.
Four or five notches are normally sufficient to secure the
car on flat terrain, while nine or ten may be necessary on
a steep slope with the car loaded.
IMPORTANT If this is not the case, contact a Fiat Deal-
ership to have the handbrake adjusted.
When the handbrake is on and the ignition key is at
MAR,
the instrument panel warning light
xwill come on.
To release the handbrake, proceed as follows:
❒pull up slightly on the lever and press release button A;
❒hold button Adown and lower the lever. The x
warning light on the instrument panel will go out.
Press the brake pedal when carrying out this operation
to prevent the car from moving accidentally.
PARKING THE VEHICLE
Proceed as follows:
❒stop the engine and engage the handbrake;
❒engage a gear (first gear if the vehicle is parked uphill
or reverse if it is facing downhill) and leave the wheels
turned.
If the car is parked on a steep slope, it is further advis-
able to block the wheels with a wedge or stone. Do not
leave the key in the ignition as this drains the battery.
Always remove the key when you leave the car.
Never leave children unattended in the
car. Always remove the ignition key when
leaving the car and take it with you.
WARNING
149-160 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 152

159
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SNOW TYRES
Use snow tyres of the same size as the normal tyres pro-
vided with the car.
A Fiat Dealership will be happy to provide advice con-
cerning the most suitable type of tyre for the customer’s
requirements.
For the type, pressures and specifications of the snow tyre
to be used, follow carefully the instructions given in the
“Wheels” paragraph of the “Technical specifications” sec-
tion.
The performance of these tyres is considerably reduced
when the tread depth is less than 4 mm. If this is the case,
replace them.
Due to their specific features, the performance of snow
tyres is much lower than that of standard tyres in normal
conditions or on long motorway stretches. You should
therefore use them only in the conditions for which they
were designed.
IMPORTANT When using snow tyres with a maximum
speed index below the one that can be reached by the
car (increased by 5%), place a notice in the passenger com-
partment, plainly in view, which states the maximum speed
allowed by the snow tyres (as per EC Directive).
All four tyres should be the same (brand and profile) to
ensure greater safety when driving and braking as well as
making the car more responsive.
Remember that you should not change the rotation di-
rection of the tyres.
SNOW CHAINS
The use of snow chains should be in compliance with lo-
cal regulations. Snow chains may be fitted only to the front
wheel tyres (drive wheels). Use of Lineaccessori Fiat snow
chains is recommended. Check the tension of the chains
after the first few metres have been driven.
IMPORTANT When the snow chains are on, use the ac-
celerator with extreme care to prevent, or to limit as much
as possible, the driving wheels from skidding. This could
cause the chains to break, resulting in damage to the ve-
hicle body or mechanical components.
IMPORTANT Snow chains can only be fitted on 15”
tyres. Use compact 9-mm snow chains.
The maximum speed for snow tyres
marked “Q” is 160 km/h, while it is 190
km/h for “T” tyres and 210 km/h for “H” tyres.
You should, however, always stick to the speed
limits of the highway code.
WARNING
149-160 PUNTO FL EN 3ed 9-12-2009 13:41 Pagina 159

164
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
Degraded engine oil should be replaced as
soon as possible after the warning light
comes on, and never more than 500 km after it
first comes on.
Failure to change the oil within the first 1000 km
may result in severe damage to the engine and in-
validate the warranty. Remember that when the
warning light comes on, it does not mean that the
level of engine oil is low, so if the light flashes you
do not need to top up the engine oil.
WARNING
DOOR/BOOT/BONNET OPEN (red)
On certain versions, the warning light turns on
when one or more doors or the boot are not
properly closed.
A specific message is displayed on certain versions. You
will hear a warning sound if a door is open and the car is
moving.
´
DUALDRIVE ELECTRIC POWER
STEERING FAILURE (red)
(for versions/markets where provided)
This warning light comes on when the ignition key
is turned to MAR, but it should go off after a few sec-
onds.
If the warning light stays on, you will not get the benefit
from the electric power steering and the effort needed
to turn the wheel will be greatly increased, although it will
still be possible to steer the car. Contact a Fiat Dealership.
On some versions the display shows the associated mes-
sage.
g
Note that engine oil degrades faster under the following
circumstances:
– use of the vehicle mainly for city driving, requiring more
frequent regeneration of the DPF
– use of the vehicle for short drives, in which the engine
does not have time to reach its regular operating tem-
perature
– repeated interruption of the regeneration process, sig-
nalled by the DPF warning light coming on.
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 164

165
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
SEAT BELT NOT FASTENED (red)
The warning light on the display lights up per-
manently when the car is not moving and the dri-
ver’s seat belt is not correctly fastened. It will flash,
and be accompanied by an audible warning, if the front seat
belts are not correctly fastened when the vehicle is mov-
ing. The SBR (Seat Belt Reminder) system’s audible warn-
ing can be disabled only by a Fiat Dealership. On some ver-
sions the system can be reactivated from the setup menu.
<
LOW ENGINE OIL LEVEL (red)
(for versions/markets where provided)
When turning the ignition key to MAR, the
warning light turns on but it should go off after a
few seconds. This warning light where provided comes on
when the engine oil level falls below the minimum rec-
ommended value. Restore the correct engine oil level (see
“Checking fluid levels” in the “Servicing and care” section).
A specific message is displayed on certain versions.
k
EBD FAULT (red)
(amber)
Warning lights
xand >lit at the
same time with the engine running in-
dicates an EBD system failure or that the system is not
available. This may cause premature locking of the rear
wheels in the event of violent braking, causing the car to
swerve. Drive very carefully to a Fiat Dealership to have
the system inspected immediately.
On some versions the display shows the associated mes-
sage.> x
INJECTION SYSTEM FAULT
(Multijet versions – amber)
EOBD SYSTEM FAULT
(petrol versions – amber)
Injection system failure
Under normal conditions, turning the ignition key to MAR,
the warning light turns on but it should go off after the en-
gine starts.
If the warning light stays on or comes on when travelling,
it means there is a fault in the injection system which could
cause loss of performance, poor handling and high fuel con-
sumption levels.
A specific message is displayed on certain versions. Un-
der these conditions, the vehicle can continue travelling at
moderate speed without demanding excessive effort from
the engine. In any case, you should go to a Fiat Dealer-
ship as soon as possible.
U
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 165

GENERIC INDICATOR
(amber)
(for versions/markets where provided)
The warning light turns on in the following cir-
cumstances:
Engine oil pressure sensor failure
The warning light turns on when a failure is detected in
the engine oil pressure sensor. Go to a Fiat Dealership to
have the fault fixed as soon as possible. The associated mes-
sage is displayed on some versions.
Start&Stop fault
(for versions/markets where provided)
The warning light comes on when a Start&Stop failure is de-
tected.
A specific message is displayed on certain versions.
169
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
REAR FOG LIGHTS (amber)
The light comes on when the rear fog lights are
turned on.
4
Fuel cut-off intervention
(for versions/markets, where provided)
The warning light comes on when the fuel cut-off system
intervenes (see “Multifunction display” in the “Controls”
section).
A specific message is displayed on certain versions.
Rain sensor fault
(for versions/markets where provided)
The warning light comes on when a rain sensor failure is
detected (see “Multifunction display” in the “Controls”
section). Contact a Fiat Dealership.
A specific message is displayed on certain versions.
Parking sensor fault
(for versions/markets where provided)
The warning light turns on when a failure is detected in
the parking sensors. In this case, contact a Fiat Dealership.
A specific message is displayed on certain versions.
Tyre pressure monitoring system (TPMS) failure
(for versions/markets where provided)
The warning light turns on when a failure is detected in
the TPMS system (for versions/markets where provided).
Contact a Fiat Dealership as soon as possible.
Should one or more wheels without a sensor be fitted, the
instrument panel warning light will come on and stay on
until the initial conditions are restored.
A specific message is displayed on certain versions.
è
The failure relating to these lights could be: one or more
blown bulbs, a blown protection fuse or a break in the elec-
trical connection. On certain versions warning light è
turns on as an alternative. On some versions the display
shows the associated message.
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 169

172
KNOWING
YOUR
VEHICLE
SAFETY
STARTING
AND DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING
AND CARE
TECHNICAL
SPECIFICATIONS
CONTENTS
IMPORTANT Do not continue driving with one or more
flat tyres as handling may be compromised. Stop the car,
avoiding harsh braking or steering manoeuvres. Replace
the wheel immediately with the small spare wheel (for ver-
sions/markets where provided) or carry out a repair us-
ing the dedicated kit (see “Changing a wheel” in the “In
an emergency” section) and contact a Fiat Dealership as
soon as possible.
Tyre pressure unsuitable for speed
Should you need to travel at a speed higher than 160 km/h,
inflate the tyres to the pressures specified in “Tyre pres-
sures”.
If the TPMS system (for versions/markets where provid-
ed) detects that the pressure of one or more tyres is un-
suitable for the current speed, the warning light will turn
on (together with the message on the display) (see “Tyre
pressure low” in this section) and it will stay on until the
car slows down to a speed below the preset threshold.
IMPORTANT In this case, slow down immediately because
tyre overheating could damage tyre performance and dura-
bility beyond repair, and may even make the tyre explode. CHECK TYRE PRESSURE
(amber)
TYRE PRESSURE LOW (amber)
TYRE PRESSURE UNSUITABLE FOR
SPEED
(amber)
(for versions/markets where provided)
When the ignition key is moved to MAR position, the
warnintg light turns on but should go off after a few sec-
onds.
Check tyre pressures
The warning light turns on to indicate the flat tyre. Should
two or more tyres be flat, the display will show the indi-
cations corresponding to each tyre in sequence.
Restore correct tyre pressures as soon as possible (see
“Cold tyre pressures” in the “Technical specifications” sec-
tion).
Tyre pressure low
The warning light on the panel comes on when the pres-
sure of one or more tyres falls below a preset level. In this
way, the TPMS system warns the driver that one or more
tyres may be dangerously flat and probably punctured.
n
161-174 PUNTO FL EN 3ed 9-12-2009 13:40 Pagina 172