2009 FIAT PANDA replace light

148KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0699m
fig. 138
F0Z0676m
fig. 139
BOTTLE REPLACEMENT PROCEDURE
To replace the bottle, proceed as follows:❒
disconnect the connection A-fig. 139;
❒
turn the bottle counter-clockwise to replace and raise
it;
❒
fit the new bottle and turn it clockwise;
❒
secure the connection A to the bottle and fit the trans-
parent tube B in the relevant compartment.
Absolutely inform the dealership that the
tyre has been repaired using the quick tyre
repair kit. Hand the instruction brochure over to
the personnel charged with treating the tyre re-
paired with the kit.
WARNING
FOR CHECKING AND RESTORING PRESSURE
ONLYThe compressor can be also used just for restoring pres-
sure. Release the bottle connection A-fig. 139 and connect
it directly to the tyre valve fig. 138; in this way the bottle
is not connected to the compressor anymore and the seal-
ing fluid will not flow into the tyre.
135-168 PANDA EN 7-10-2009 14:07 Pagina 148

149KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
CHANGING A BULBGENERAL INSTRUCTIONS❒
Before changing a bulb check the contacts for oxidation;
❒
burnt bulbs must be replaced by others of the same type
and power;
❒
always check the headlight beam aiming after changing
a bulb;
❒
when a light is not working, check that the corre-
sponding fuse is intact before changing a bulb. For the
location of fuses, refer to the paragraph “Replacing fus-
es” in this chapter.
Modifications or repairs to the electric sys-
tem that are not carried out properly or
do not take the system technical specifications in-
to account can cause malfunctions leading to the
risk of fire.
WARNING
Halogen bulbs contain gas under pressure;
if they break, glass fragments may be dis-
persed.
WARNING
When handling halogen bulbs, only touch
the metal part. If the transparent bulb is
touched with the fingers, its lighting inten-
sity is reduced and life of the bulb may be com-
promised. In the event of accidental contact, wipe
the bulb with a cloth moistened with alcohol
and leave it to dry.
IMPORTANT The headlight inner surface might be slight-
ly misted: this should not be considered irregular rather
a natural phenomenon due to low temperature and the air
humidity level. Misting will disappear as soon as the head-
lights are turned on. The presence of drops inside the
headlights indicates infiltration of water. Contact a Fiat
Dealership.
Where possible, it is advisable to have bulbs
changed at a Fiat Dealership. The correct
operation and aiming of the outer lights are
absolutely important to the safety of the car and
its passengers and the subject of specific laws about
road traffic.
135-168 PANDA EN 7-10-2009 14:07 Pagina 149

153KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0092m
fig. 144
F0Z0094m
fig. 146
F0Z0093m
fig. 145
❒
remove the burnt bulb F-fig. 144 and fit the new one;
❒
refit by reversing the above mentioned operations.
To replace the main/dipped beam light bulb, proceed as
follows:
❒
release the clip A-fig. 141 and remove the cap B;
❒
remove the connector G-fig. 145;
❒
release the bulb-holder clip H-fig. 145;
❒
remove the burnt bulb I-fig. 146 and fit the new one;
❒
refit by reversing the above mentioned operations.
135-168 PANDA EN 7-10-2009 14:07 Pagina 153

154KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0095m
fig. 147
F0Z0227m
fig. 149
F0Z0604m
fig. 148
FRONT FOG LIGHTS
(for versions/markets where provided)
To change the halogen bulb, proceed as follows:❒
undo the two screws A and B-fig. 149 for fog light fas-
tening on the bumper and take out trim and fog light,
disconnecting the connector;
❒
loosen the cover C-fig. 150 and remove the connec-
tor D;
❒
release the clip E-fig. 151 and remove the bulb F;
❒
refit by reversing the above mentioned operations. SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒
push the lamp lens A-fig. 147 in the car running direc-
tion (it is pressure-fit);
❒
remove the bulb B-fig. 148 and replace it;
❒
remove the lamp lens.
135-168 PANDA EN 7-10-2009 14:07 Pagina 154

156KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0099m
fig. 155
F0Z0098m
fig. 154
F0Z0100m
fig. 156
NUMBER PLATE LIGHTS
To change the bulb, proceed as follows:❒
use a screwdriver to remove the retaining spring as
shown fig. 155 and remove the lens A-fig. 156; take out
the bulb B from the bulb-holder;
❒
replace the 12 V - 5 W pressure-fit bulb in the bulb-
holder and refit the lens. Figure 154
D 12 V – 21 W bulb for reversing light on right light unit;
❒
rear fog light on left light unit;
❒
on right-hand drive versions, reversing light in the
left rear light unit and rear fog lamp in the right rear
light unit;
E 12 V – 21 W bulb for the direction indicators;
F 12 V – 21/5 W double-light bulb for stop light and tail
lights.
135-168 PANDA EN 7-10-2009 14:07 Pagina 156

157KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0211m
fig. 158
F0Z0101m
fig. 157
F0Z0210m
fig. 159
❒
release the clip C-fig. 158 and remove the bulb unit from
the lens unit;
❒
replace the pressure-fit burnt out bulb D;
❒
refit by reversing the above mentioned operations. THIRD STOP LIGHTS
To change one or more bulbs, proceed as follows:
❒
undo the two screws A-fig. 157 and remove the whole
cover;
❒
disconnect the connector B-fig. 159 and remove the
light unit;
135-168 PANDA EN 7-10-2009 14:07 Pagina 157

158KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0193m
fig. 160
F0Z0213m
fig. 161
F0Z0214m
fig. 162
❒
replace the bulb C-fig. 162 releasing the side contacts,
insert the new bulb and make sure that it is correctly
clamped between the contacts;
❒
close the cap back and refit the lens.
CHANGING AN INTERIOR LIGHTFor the type of bulb and power rating, see “Changing
a bulb”.
CEILING LIGHT
To change the bulbs, proceed as follows:❒
using the screwdriver provided, extract the ceiling light
A-fig. 160 working in the point shown by the arrow;
❒
open the cover B-fig. 161 as shown;
135-168 PANDA EN 7-10-2009 14:07 Pagina 158

159KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0102m
fig. 163
F0Z0103m
fig. 164
BOOT LIGHT
(for versions/markets, where provided)
To change the bulbs, proceed as follows:❒
open the tailgate;
❒
using the screwdriver provided, extract the ceiling light
A-fig. 163 working in the point shown;
❒
open the bulb cover B-fig. 164 and replace the pressure-
fit bulb C;
❒
close again the bulb cover B on the lens;
❒
refit correctly the light pressing one side and then the
other until the locking click is heard.
135-168 PANDA EN 7-10-2009 14:07 Pagina 159