2009 FIAT PANDA technical specifications

155KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0229m
fig. 151
TOP
OFF
ON
F0Z0228m
fig. 150
F0Z0097m
fig. 153
F0Z0096m
fig. 152
❒
loosen the four screws B-fig. 153 from their housings
and remove the bulb-holder C;
❒
remove the bulbs, pushing them slightly and rotating
counter-clockwise;
❒
refit by reversing the above mentioned operations. REAR LIGHT UNIT
To change the bulb proceed as follows:
❒
loosen the three screws A-fig. 152 from their seats, pull
gently outwards until releasing the whole headlight from
the three clips (press-fit), then release the connector;
135-168 PANDA EN 7-10-2009 14:07 Pagina 155

156KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0099m
fig. 155
F0Z0098m
fig. 154
F0Z0100m
fig. 156
NUMBER PLATE LIGHTS
To change the bulb, proceed as follows:❒
use a screwdriver to remove the retaining spring as
shown fig. 155 and remove the lens A-fig. 156; take out
the bulb B from the bulb-holder;
❒
replace the 12 V - 5 W pressure-fit bulb in the bulb-
holder and refit the lens. Figure 154
D 12 V – 21 W bulb for reversing light on right light unit;
❒
rear fog light on left light unit;
❒
on right-hand drive versions, reversing light in the
left rear light unit and rear fog lamp in the right rear
light unit;
E 12 V – 21 W bulb for the direction indicators;
F 12 V – 21/5 W double-light bulb for stop light and tail
lights.
135-168 PANDA EN 7-10-2009 14:07 Pagina 156

157KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0211m
fig. 158
F0Z0101m
fig. 157
F0Z0210m
fig. 159
❒
release the clip C-fig. 158 and remove the bulb unit from
the lens unit;
❒
replace the pressure-fit burnt out bulb D;
❒
refit by reversing the above mentioned operations. THIRD STOP LIGHTS
To change one or more bulbs, proceed as follows:
❒
undo the two screws A-fig. 157 and remove the whole
cover;
❒
disconnect the connector B-fig. 159 and remove the
light unit;
135-168 PANDA EN 7-10-2009 14:07 Pagina 157

158KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0193m
fig. 160
F0Z0213m
fig. 161
F0Z0214m
fig. 162
❒
replace the bulb C-fig. 162 releasing the side contacts,
insert the new bulb and make sure that it is correctly
clamped between the contacts;
❒
close the cap back and refit the lens.
CHANGING AN INTERIOR LIGHTFor the type of bulb and power rating, see “Changing
a bulb”.
CEILING LIGHT
To change the bulbs, proceed as follows:❒
using the screwdriver provided, extract the ceiling light
A-fig. 160 working in the point shown by the arrow;
❒
open the cover B-fig. 161 as shown;
135-168 PANDA EN 7-10-2009 14:07 Pagina 158

159KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0102m
fig. 163
F0Z0103m
fig. 164
BOOT LIGHT
(for versions/markets, where provided)
To change the bulbs, proceed as follows:❒
open the tailgate;
❒
using the screwdriver provided, extract the ceiling light
A-fig. 163 working in the point shown;
❒
open the bulb cover B-fig. 164 and replace the pressure-
fit bulb C;
❒
close again the bulb cover B on the lens;
❒
refit correctly the light pressing one side and then the
other until the locking click is heard.
135-168 PANDA EN 7-10-2009 14:07 Pagina 159

160KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
F0Z0087m
fig. 165
Refer to the tables on the following pages to identify the
protection fuse.
If a general fuse (MEGA-FUSE, MIDI-
FUSE, MAXI-FUSE) cuts in, do not at-
tempt any repair and contact a Fiat Dealership.
WARNING
Before replacing a fuse, make sure the ig-
nition key has been removed and that all
the other services are switched off and/or
disengaged.If the replaced fuse blows again, contact
a Fiat Dealership.
WARNING
Never replace a blown fuse with metal
wires or other recovered material.
WARNING
Never replace a fuse with another of high-
er power: FIRE HAZARD.
WARNING
REPLACING FUSESGENERAL FEATURES fig. 165
Fuses protect the electric system: they cut in (i.e. they
blow) in the event of a failure or improper action on the
system.
When a device does not work, check the efficiency of its
fuse: the filament A must be intact. If it is, replace the blown
fuse with another with the same amperage (same colour).
B undamaged fuse.
C fuse with damaged filament.
To facilitate fuse replacement, use the pliers D hooked
to the fuse-box on the dashboard left-hand side.
135-168 PANDA EN 7-10-2009 14:07 Pagina 160

161KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGESIN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
FUSE LOCATION
Fuse-boxes are located on the steering wheel left-hand
side fig. 166 and 167.
To gain access to the fuse-boxes, undo the cover F fas-
tening screw E.
G wired control unit.
H body-computer control unit.
D fuse extracting pliers.
The number identifying the electrical component corre-
sponding to each fuse is on the cover back.
fig. 167 fig. 166
F37
18
9
16
F0Z0139m
F0Z0260m
135-168 PANDA EN 7-10-2009 14:07 Pagina 161

162KNOW
YOUR VEHICLE
SAFETY
CORRECT USE
OF THE CAR
WARNING LIGHTS
AND MESSAGES
IN
AN EMERGENCYCAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
A second fuse-box is located on the right-hand of the en-
gine compartment, next to the battery; to reach it re-
lease the spring I, the tabs M and remove the lid L.
The number identifying the electrical component corre-
sponding to each fuse is on the cover back.
fig. 168
fig. 169
F0Z0652m
F0Z0704m
Fuses in the engine compartment fig. 168 and 169
135-168 PANDA EN 7-10-2009 14:07 Pagina 162