2009 FIAT PANDA 4x4 Supplement Manual

8
FIAT PANDA 4 x 4
❒loosen the three fastening screws A-
fig. 16and remove the headlight cov-
er;
❒remove the cover by removing the
catches B;
❒remove the lens fig. 17by loosening
the three fastening screws A;
❒turn connector A-fig. 18counter-
clockwise and remove it;
❒remove the bulb B-fig. 18and fit the
new bulb.
To change the direction indicator bulb,
proceed as follows:
❒loosen the two fastening screws A-
fig. 19and remove the cover B;
❒loosen the fastening screws A-fig. 20
and remove the lens B;
❒remove the cap A-fig. 21from the lens
Band remove the bulb holder C;
❒remove bulb Dby pushing it slightly and
turning it counter-clockwise, then fit
the new bulb.
To change side direction indicators, third
brake light and number plate light bulbs re-
fer to paragraph “When needing to change
a bulb” in section “In an emergency” in the
attached Owner Handbook.
fig. 16F0G0620mfig. 18F0G0622m
fig. 17F0G0621mfig. 19F0G0623m
fig. 20F0G0624m
fig. 21F0G0631m
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 8

9
FIAT PANDA 4 x 4
REAR LIGHT UNITS
The bulbs are arranged inside the light unit
as follows fig. 22:
A12V-W5W, double filament bulb for
brake lights/taillights.
B12V-P21W bulb for direction indica-
tors.
C12V-P21W bulb for rear fog light (left
headlight) or reversing light (right head-
light).To change a bulb proceed as follows:
❒loosen the three screws A-fig. 23then
pull gently the headlight outwards un-
til releasing it from the three catches;
fig. 23F0G0625mfig. 24F0G0626m
❒loosen the four screws A-fig. 24and
disconnect the two connectors;
❒remove the required bulb holder turn-
ing it counter-clockwise;
❒remove the required bulb (A, Bor C-
fig. 22), pushing it slightly and turning
it counter-clockwise (bayonet cou-
pling), then fit the new bulb.
fig. 22F0G0627m
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 9

10
FIAT PANDA 4 x 4
WASHING THE CAR
After using the car off-road (wheels, body,
underengine and underbody protections
very dirty), remember to wash it and to
clean accurately radiators (engine and air-
conditioner), radiator fan and wheels (rims
and wheelhouses), underengine and un-
derbody protections to preserve their
regular operation and to guarantee prop-
er ventilation of brake discs, perfect wheel
geometry and regular operation of the
propeller shaft.
TOWING THE CAR
The car can only be towed in one of the
following ways (always and exclusively
with the engine off, gearbox in neutral and
handbrake disengaged):
– with the 4 wheels on the roadbed;
– with front wheels raised or resting on
the wrecking car floor and rear wheels
resting on a suitable truck;
– with rear wheels raised or resting on the
wrecking car floor and front wheels rest-
ing on a suitable truck;
– on wrecking car, with front and rear
wheels resting on the wrecking car floor.
TOWING TRAILERS
IMPORTANT If the car is used at its max.
towing capacity on sloping road, change
engine oil every 10,000 km.
As concerns tow hook installation in-
structions and warnings refer to the at-
tached Owner Handbook.
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 10

11
FIAT PANDA 4 x 4
ASSEMBLY DIAGRAM, fig. 25
The assembly diagram with the new tow
hook fixing points is given below.
The tow hook structure must be fastened
in the points identified by symbol Øus-
ing a total of 4 M8 screws and 2 M12
screws. Internal plates 1-fig. 25thickness
shall be 6 mm. The hook should be fas-
tened to the body avoiding any type of
drilling and trimming of the rear bumpers
that remains visible when the hook is re-
moved.
IMPORTANT It is compulsory to fasten,
at the same height as the tow hook and
in a clearly visible position, a label of suit-
able size and material with the following
information: MAX LOAD ON BALL 60 kg
After fitting, screw holes shall be sealed to
prevent an exhaust gas inlet.
fig. 25F0G0266m
existing screw
existing hole
existing hole
standard tow ball existing hole
existing
screw
existing hole
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 11

12
FIAT PANDA 4 x 4
20 40 60 80 100 120 140 160 180
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●●●●● ●●●●
●● ● ●
●●●●● ●●●●
●●●●● ●●●●
●
●● ● ●
●● ● ●
●● ● ●
SERVICE SCHEDULE
Thousands of km
Check tyre conditions/wear and adjust pressure
if required
Check light system operation (headlights, direction indicators,
hazard lights, passenger compartment lights, boot lights,
warning lights, etc.)
Check windscreen wiper/washer operation,
adjust nozzles
Check windscreen/rear window blade
position/wear
Check front disk brake pad conditions and wear
Check rear disk brake pad conditions and wear
Sight inspect the conditions of: body external parts,
underbody protection, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.)
Check cleanness of locks, bonnet and boot and lever cleanness
and lubrication
Check tension and adjust accessory drive belts
(excluding engines with automatic belt tighteners)
Sight inspect accessory drive belt conditions
Check and adjust tappet clearance (petrol versions)
Check handbrake lever stroke
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 12

13
FIAT PANDA 4 x 4
20 40 60 80 100 120 140 160 180
●● ●
●● ●●●●●●●
●●
●
●●●●
●●●●
●●
●● ●●●●●●●
●● ●
●● ●●●●●●●
●●●●
●● ●
Thousands of km
Change air cleaner cartridge
(every 30,000 km/for 1.3 Multijet engine)
Top up fluids
(engine coolant, brakes, windscreen, battery, etc.)
Check timing belt
(excluding 1.3 Multijet engines)
Replace timing belt (*)
(excluding 1.3 Multijet engine)
Change spark plugs (petrol versions)
Check engine control system operation
(through diagnosis socket)
Check mechanical transmission oil level
Change engine oil and oil filter
(every 30,000 km/for 1.3 Multijet engine)
Change brake fluid (or every 2 years)
Change pollen filter (or every year)
Check exhaust emissions/smoke (1.3 Multijet engine)
Replace fuel filter cartridge (Green-filter)
(1.3 Multijet engine)
(*) Irrespective of mileage, the timing drive belt must be replace every 4 years for heavy duty applications, cold climates, town use, long periods idling) or at
least every 5 years.
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 13

14
FIAT PANDA 4 x 4
Engine code
169A4000 (*)
188 A 8000
169A4000 (*)
188 A 8000
188 A 8000
Fiat Panda 4 x 4
Fiat Panda 4 x 4 Climbing
Fiat Panda 4 x 4 CROSS
ENGINE CODES
BODY VERSIONS
Fiat Panda 4 x 4
Fiat Panda 4 x 4 Climbing
Fiat Panda 4 x 4 CROSS
Versions Engine code Body version
Euro 4 Euro 5
4 seat 5 seat 4 seat 5 seat
1.2 – – 169AXF2A 09 169AXF2A 09B
1.3 Multijet 169AXC2A 0FF 169AXC2A 0FG – –
1.2 – – 169AXF2A 09C 169AXF2A 09D
1.3 Multijet 169AXC2A 0FH 169AXC2A 0FI – –
1.3 Multijet 169AXC2A 0FL – – –Engine
1.2
1.3 Multijet
1.2
1.3 Multijet
1.3 Multijet
Versions
(*) Euro 5
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 14

15
FIAT PANDA 4 x 4
ENGINE
GENERAL INFORMATION
Type code
Cycle
Number and layout of cylinders
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Max power (EEC) kW
HP
corresponding speed rpm
Max. torque (EEC) Nm
kgm
corresponding speed rpm
Spark plugs
Fuel
1.2 (Euro 5)
169A4000
Otto
4 in line
70.8 x 78.86
1242
11.1 : 1
51
69
5500
102
10.4
3000
NGKZKR7a-10
Unleaded petrol
95 R.O.N.1.3 Multijet 75 HP
169A1000
Diesel
4 in line
69.6 x 82
1248
17.6 : 1
55
75
4000
145
14.8
1500
–
Diesel fuel for motor vehicles
(EN 590 standard)
603_97_560 PANDA 4X4 Euro 5 GB 11-12-2009 9:31 Pagina 15