2009 FIAT IDEA technical specifications

180
STARTING
AND DRIVING
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
INTERIORS
Periodically check that water is not trap-
ped under the mats (due to water drip-
ping off shoes, umbrellas, etc.) which could
cause oxidisation of the sheet metal.
CLEANING SEATS AND FABRIC
PARTS
Remove dust with a soft brush or a va-
cuum cleaner. It is advisable to use a moi-
st brush on velvet upholstery.
Rub the seats with a sponge moistened
with a solution of water and neutral de-
tergent.
LEATHER SEATS
Remove dry dirt with a moist chamois
leather or cloth without pressing too hard.
Remove stains of liquid or grease with a
dry absorbing cloth. Do not rub. Then wi-
pe with a soft cloth or chamois leather
dipped in water and mild soap.
Use specific products for persistent stains
paying attention to instructions for use.
IMPORTANT Never use alcohol. Make
sure that the products used do not con-
tain alcohol or derivates, even in low con-
centrations. INTERIOR PLASTIC PARTS
It is advisable to clean interior parts with
a moist cloth and a solution of water and
mild soap. Use specific products for clea-
ning plastic, without solvents and specifi-
cally designed to prevent damage to the
appearance and colour of the treated parts
to remove grease and tough stains.
IMPORTANT Never use spirit or petro-
leum to clean the instrument panel tran-
sparent cover or other plastic parts.
Do not keep aerosol cans in
the car: risk of explosion. Ae-
rosol cans must not be exposed to a
temperature exceeding 50°C. When
the vehicle is exposed to sunlight, in-
ner temperature can greatly exceed
this value.
WARNING
The fabric upholstery of your
car is designed to withstand
the normal wear and tear of
your car for a long time. So-
me precautions are however needed.
Avoid prolonged rubbing against
clothing accessories, such as metal
buckles, Velcro strips and the like, whi-
ch by applying a high pressure on the
fabric in a small area could cause the
breakage of some threads and damage
the upholstery.
LEATHER STEERING
WHEEL/GEAR KNOB
These components must be cleaned with
mild soap and water only. Never use spi-
rit and/or alcohol based products. Read
the product label carefully before using
specific products for cleaning the interiors:
make sure the product does not contain
alcohol or alcohol based substances.
If window cleaner accidentally drips onto
the steering wheel or gear lever knob, wi-
pe away immediately and then wash the
concerned area with mild soap and water.
IMPORTANT Be careful when arranging
a steering wheel lock device, where ap-
plicable, to prevent damaging the leather
upholstery by rubbing.

181
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................. 182
ENGINE CODES - BODYWORK VERSIONS ............. 184
ENGINE ................................................................................. 185
FUEL FEED/IGNITION ....................................................... 187
TRANSMISSION UNIT ...................................................... 187
BRAKES .................................................................................. 188
SUSPENSIONS ..................................................................... 188
STEERING SYSTEM ............................................................. 188
WHEELS ................................................................................. 189
DIMENSIONS ....................................................................... 193
PERFORMANCE .................................................................. 193
WEIGHTS .............................................................................. 194
CAPACITIES ......................................................................... 195
FLUIDS AND LUBRICANTS ............................................ 196
FUEL CONSUMPTION ...................................................... 198
CO
2EMISSIONS .................................................................. 199
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S

182
STARTING
AND DRIVING
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA
We recommend taking note of the iden-
tification codes. The identification data are
printed on labels fig. 1in the following po-
sitions:
1- Model plate
2- Chassis marking.
3- Bodywork paint identification plate.
4- Engine marking.
MODEL PLATE
fig. 2
This plate is fitted to the engine compart-
ment front crossmember and contains the
following data:
B- Type-approval number.
C- Vehicle type code.
D- Chassis number.
E- Maximum vehicle weight fully loaded.F- Maximum vehicle weight fully loaded
with trailer.
G- Maximum vehicle weight on front ax-
le.
H- Maximum vehicle weight on rear ax-
le.
I- Engine Type
L- Bodywork version code.
M- Spare part code.
N- Smoke opacity index (for diesel en-
gines).
fig. 1
4
21
3
F0H0225mfig. 2F0H0760m
IN AN
EMERGENCY

183
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
CHASSIS MARKING fig. 3
This is printed on the passenger com-
partment floor bed near the front right
seat.
The label can be accessed by lifting the
window in the mat and comprises:
❒vehicle model;
❒chassis number.
fig. 3F0H0227m
fig. 4F0H0228m
BODYWORK PAINT
IDENTIFICATION PLATE fig. 4
This plate is applied to the bonnet and
shows the following data:
A- Paint manufacturer.
B- Colour name.
C- Fiat colour code.
D- Respray and touch up code.
ENGINE MARKING
It is stamped onto the cylinder block (pas-
senger compartment side) and shows the
type and the serial number.

184
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
ENGINE CODES - BODYWORK VERSIONS
Versions
1.2
16V
1.48V (◊)
1.4 16V
1.416V90 CV (◊)
1.3 Multijet 70 CV
1.3 Multijet 90 CV
1.3 Multijet 95 CV
1.6 Multijet
1.6 Multijet 115 CV (◊)
Bodywork code
350 AXD1A 03 (5 seats)
350 AXD1A 03C (4 seats)
350 AXF1A 08N (5 seats)
350 AXF1A 08P (4 seats)
350 AXA1B 07E (5 seats)
350 AXA1B 07F (4 seats)
350 AXE1A 06
350 AXB1A 01N (5 seats)
350 AXB1A 01P (4 seats)
350 AXG1A 09AA (5 seats)
350 AXG1A 09AB (4 seats)
350 AXG1A 09AC (5 seats) (*)
350 AXG1A 09AD (4 seats) (*)
350AXM1A 13 (5 seats) (*)
350 AXH1A 11L (5 seats) (*)
350 AXH1A 11F (4 seats) (*)
350 AXL1A 12l (5 seats) (*)
350 AXL1A 12F (4 seats) (*)
(◊) Engine version for some versions/markets only
(*) DPF versionEngine type code
188A5000
350A1000
843A1000
192B2000
188A9000
199A3000
199B1000
350A2000
350A3000

185
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
(◊) Engine version for some versions/markets only
ENGINE
INTRODUCTION
Type code:
Cycle
Cylinder number and position
Number of valves per cylinder
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Max. EEC power kW
HP
corresponding rpm rpm
Max. EEC torque Nm
kgm
corresponding rpm: rpm
Spark plugs
Fuel
1.2 16V
188A5000
Otto
4 in line
4
70.8 x 78.86
1242
10.6±0.2
59
80
5000
114
11.6
4000
NGK DCPR7E-N-10
BOSCH YR7DEU
Unleaded petrol
95 RON
(EN228 specifications)1.4
16V
843A1000
Otto
4 in line
4
72 x 84
1368
11±0,2
70
95
5800
128
13
4500
NGK ZKR7A-10
Unleaded petrol
95 RON
(EN228 specifications) 1.4
8V(◊)
350A1000
Otto
4 in line
2
72 x 84
1368
11±0,2
57
77
6000
115
11,7
3000
NGK ZKR7A-10
Unleaded petrol
95 RON
(EN228 specifications)

186
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INTRODUCTION
Type code:
Cycle:
Cylinder number and position:
Number of valves per cylinder:
Piston bore and stroke: mm
Total capacity: cm3
Compression ratio:
Max. EEC power: kW
HP
corresponding rpm rpm
Max. EEC torque: Nm
kgm
corresponding rpm: rpm
Spark plugs:
Fuel:
1.6 Multijet
350A2000
Diesel
4 in line
4
79.5 x 80.5
1598
16,5 ±1
88
120
3500
300
30,5
1500
–
Diesel fuel for
motor vehicles
(EN590 specifications) 1.3 Multijet 90CV
199A3000
Diesel
4 in line
4
69.6 x 82
1248
17,6 ±0,4
66
90
4000
200
20
1750
–
Diesel fuel for
motor vehicles
(EN590 specifications) 1.3 Multijet 70CV
188A9000
Diesel
4 in line
4
69.6 x 82
1248
18 ±0,4
51
70
4000
180
18,3
1750
–
Diesel fuel for
motor vehicles
(EN590 specifications)1.3 Multijet 95CV
199B1000
Diesel
4 in line
4
69.6 x 82
1248
16,8 + 0,2 / - 0,4
70
95
4000
200
20
1500
–
Diesel fuel for
motor vehicles
(EN590 specifications)

187
STARTING
AND DRIVING
IN AN
EMERGENCY
MAINTENANCE
AND CARE
ALPHABETICAL
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
FUEL FEED/IGNITION
Fuelfeed
(◊) Engine version for some versions/markets only
TRANSMISSION UNIT
Gearbox
Clutch
Drive
(◊) Engine version for some versions/markets only1.3 Multijet - 1.6 Multijet
Common Rail Multijet direct injection
electronically controlled with
turbo and intercooler 1.2
16V - 1.48V (◊) - 1.416V
Multipoint sequential phased injection,
integrated with ignition,
returnless system
1.2
16V - 1.48V (◊) - 1.3 Multijet - 1.6 Multijet
Five forward gears plus reverse with synchronisers
for forward gears
Hydraulic control and play-less pedal
Front1.4 16V
Five forward gears plus reverse with synchronisers
for forward gears
Hydraulic control and play-less pedal
Front
Modifications or repairs to the fuel feed system that are not carried out properly or do not take the system’s te-
chnical specifications into account can cause malfunctions leading to the risk of fire.