2009 FIAT GRANDE PUNTO technical specifications

180
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
CONTROLS
AND DEVICES
SERVICE
AND CARE
The fabric upholstery of your
car is designed to withstand
normal wear and tear for
a long time. Some precautions
are however needed. Avoid prolonged
rubbing against clothing accessories,
such as metal buckles, bosses, Velcro
strips and the like, which by applying
a high pressure on the fabric in a small
area could cause the breakage of some
threads and damage the upholstery. SEATS AND FABRIC PARTS
Remove dust with a soft brush or a vacu-
um cleaner. It is advisable to use a damp
brush on velvet upholstery.
Wipe the seats with a sponge soaked in
a solution of mild detergent and water.
Never use flammable prod-
ucts, such as petroleum
ether or modified petrol, to clean the
inside the car. The electrostatic
charges which are generated by rub-
bing during cleaning may cause a fire.
WARNING
Do not keep aerosol cans in
the vehicle: these could ex-
plode. Aerosol cans must not be ex-
posed to temperatures exceeding
50 °C. When the vehicle is exposed to
sunlight, the temperature inside can
greatly exceed this value.
WARNING
INTERIOR
Check regularly that water is not trapped
under the mats (due to drops from shoes,
umbrellas, etc.), as this could cause the
sheet metal to rust.IMPORTANT Never use alcohol- or
petrol-based products to clean the in-
strument panel.
GENUINE LEATHER STEERING
WHEEL/GEAR LEVER KNOB
These components must be cleaned with
mild soap and water only.
Never use spirits and/or alcohol-based
products.
Before using off-the-shelf products de-
signed for cleaning vehicle interiors, make
sure that they do not contain spirits and/
or alcohol-based substances.
If window cleaner accidentally drips onto
the steering wheel or gear lever knob,
wipe away immediately and then wash the
affected area with mild soap and water.
IMPORTANT When arranging a steering
wheel locking device, be careful not to dam-
age the leather upholstery.
PLASTIC PARTS
It is advisable to clean interior plastic parts
with a damp cloth and a solution of water
and mild, non-abrasive detergent. To re-
move grease and tough stains, use products
designed specifically for cleaning plastics.
These have no solvents and have been de-
signed so that they do not alter the ap-
pearance and colour of the components.
161-180 ACTUAL 1ed EN 28-08-2009 8:19 Pagina 180

181
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................. 182
ENGINE CODES – BODYWORK VERSIONS ............. 184
ENGINE .................................................................................. 185
FUEL SUPPLY ........................................................................ 186
TRANSMISSION .................................................................. 186
BRAKES .................................................................................. 187
SUSPENSIONS ...................................................................... 187
STEERING SYSTEM ............................................................. 187
WHEELS ................................................................................. 188
PERFORMANCES ................................................................ 191
DIMENSIONS ....................................................................... 192
WEIGHTS .............................................................................. 193
CAPACITIES .......................................................................... 194
FLUIDS AND LUBRICANTS ............................................. 195
FUEL CONSUMPTION ...................................................... 197
CO
2EMISSIONS .................................................................. 197
T T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 181

182
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
VIN PLATE fig. 1
The plate can be found on the left side of
the boot floor and it bears the following
identification data:
BType-approval number.
CVehicle type code.
DChassis number.
EMaximum vehicle weight fully loaded.
FMaximum vehicle weight fully loaded
with trailer.
GMaximum weight on front axle.HMaximum weight on rear axle.
IEngine type.
LBody version code.
MNumber for spare parts.
NCorrect smoke opacity index (for
diesel engines).
IDENTIFICATION DATA
We recommend taking note of the iden-
tification codes. The following identifica-
tion codes are printed and shown on the
plates:
❒Vehicle identification number (VIN)
plate.
❒Chassis marking.
❒Bodywork paint identification plate.
❒Engine marking.
fig. 1F0M0368m
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 182

183
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
CHASSIS MARKING fig. 3
This is printed on the passenger com-
partment floor, near the right front seat.
❒car model (ZFA 199000);
❒chassis number.ENGINE MARKING
This is printed onto the cylinder block and
shows the type and production serial num-
ber.
BODYWORK PAINT
IDENTIFICATION PLATE fig. 2
This can be found on the external rear
door pillar (left-hand side) and it bears the
following information:
APaint manufacturer.
BColour name.
CFiat colour code.
DColour code for touch-ups or re-
spraying.
fig. 2F0M0167mfig. 3F0M0168m
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 183

184
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
199A4000
350A1000
199A7000
199A2000
199B2000199BXA1A 01D
199BXB1A 03P
199BXH1A 20D
199BXC1A 05E
199BXC1A 05H (*)
199BXC1A 05G (❒)
199BXP1A 30F
199BXA1A 01C
199BXB1A 03C
199BXH1A 20
199BXC1A 05
199BXC1A 05C (*)
199BXC1A 05F (❒)
199BXP1A 30E
199AXA1A 00F
199AXB1A 02D
199AXH1A 19
199AXC1A 04
199AXC1A 04D (*)
199AXC1A 04F (❒)
199AXP1A 29E
199AXA1A 00G
199AXB1A 02E
199AXH1A 19B
199AXC1A 04C
199AXC1A 04E (*)
199AXC1A 04G (❒)
199AXP1A 29F
ENGINE CODES – BODYWORK VERSIONS
Version Engine type Engine type body version code
code 3 doors 5 doors
4 seats 5 seats 4 seats 5 seats
1.2
1.4
1.4 (Õ)
1.3 Multijet 75 HP
1.3 Multijet 70 HP(Õ)
(*) Version with DPF
(
❒) ECO versions 109 g CO2
(Õ) For versions/markets where provided
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 184

185
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
ENGINE
INFORMATION
Type code
Cycle
Number and layout of cylinders
Piston bore and stroke mm
Total capacity cm3
Compression ratio
Max power (EEC) kW
HP
corresponding speed rpm
Max torque (EEC) Nm
kgm
corresponding speed rpm
Spark plugs
Fuel
(Õ) For versions/markets where provided
1.3 Multijet 75 HP
199A2000
199B2000 (Õ)
Diesel
4 in line
69.6 × 82
1248
17,6:1
55
75/70 (
Õ)
4000
190
19,4
1750
–
Diesel for
motor vehicles
(EN590 specifications)
1.4
350A1000
199A7000 (Õ)
Otto
4 in line
72 × 84
1368
11,1:1
57
77/75 (
Õ)
6000
115
11,7
3000
NGK
ZKR7A-10
Unleaded petrol
95 RON
(Specification EN228)
1.2
199A4000
Otto
4 in line
70.8 × 78.86
1242
11,1:1
48
65
5500
102
10,4
3000
NGK
ZKR7A-10
Unleaded petrol
95 RON
(Specification EN228)
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 185

186
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
FUEL SUPPLY
1.2 - 1.4 1.3 Multijet
Fuel supply Multipoint electronic injection “Common Rail” Multijet direct injection
Modifications or repairs to the fuel supply system that are not carried out properly or do not take the system’s
technical specifications into account can cause malfunctions leading to the risk of fire.
WARNING
TRANSMISSION
1.2 - 1.4 - 1.3 Multijet
Gearbox Five forward gears plus reverse with synchronisersfor selecting forward gears
Clutch Self-adjusting with no free travel
Drive Front
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 186

torsion beam with interconnected wheels
187
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
BRAKES
1.2 - 1.4 - 1.3 Multijet
Service brakes:
– front disc (self-ventilating for versions/markets, where provided)
– rear drum
Parking brake controlled by hand lever, acting on rear brakes
IMPORTANT Water, ice and salt on the roads may deposit on the brake discs, reducing braking efficiency the first time the brakes
are applied.
STEERING SYSTEM
1.2 - 1.4 - 1.3 Multijet
Type rack and pinion with electric power steering
Turning circle
(kerb to kerb) m 10,9
Independent wheel McPherson-typeIndependent wheel McPherson-type
with anti-roll bar
SUSPENSION
1.2 1.4 - 1.3 Multijet
Front
Rear
181-197 ACTUAL 1ed EN 31-08-2009 12:02 Pagina 187