2009 FIAT DUCATO diagram

150
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0074mfig. 160
USING THE MANUAL GEARBOX
To engage the gears, depress the clutch pedal fully and
shift the gear lever into the required positions (the
diagram is shown on the gear knob fig. 160).
To engage 6
thgear (where provided), operate the lever
by pressing it towards the right in order to avoid
engaging 4
thgear by mistake. The same applies to the
shift from 6thto 5thgear.
IMPORTANT Reverse may only be engaged when the
vehicle is at a standstill. With the engine running, wait
for at least 2 seconds with the clutch pedal fully pressed
before engaging reverse to prevent damage to the gears
and grating.
To engage reverse R from neutral, proceed as follows:
raise ring A under the knob and at the same time move
the gear lever to the right and then backwards.
Press the clutch pedal fully to change
gears correctly. For this reason, there
must be no obstacles on the floor under the
pedals: ensure that rubber mats (if any) are
lying flat and do not interfere with the pedals.
WARNING
Do not drive with your hand resting on
the gear lever, because this pressure, even
if light, over time can wear out the
internal gearbox components.
147-160 DUCATO LUM EN 7ed 6/21/10 2:13 PM Page 150

157
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
Installation diagram for Van
versions – fig. 161
The tow hook structure must be
fastened in the points shown by the
symbol Øusing a total of 6
M10x1.25 screws and 4 M12 screws.
The internal back plates must be at
least 5 mm thick.
MAX LOAD ON BALL: 100/120 kg
according to the payload (see
“Weights” table in the “Technical
data” section).
After fitting, the screw
holes must be sealed to
prevent exhaust gas leaks.
WARNING
fig. 161F0N0189m
Existing hole
Existing nut
Existing nutExisting hole
Existing hole
laden
Standard ball M12
M12
M10 (3x)
M10 (3x)
M12
To install a tow hook, the bumpers
must be trimmed as described in the
supplier’s installation kit.
147-160 DUCATO LUM EN 7ed 6/21/10 2:13 PM Page 157

158
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
Installation diagram for Truck
and Chassis Cab versions
– fig. 162
Another tow hook specific to Truck
and Chassis Cab versions is shown
in fig. 162.
The structure Ømust be fastened in
the points shown using a total of
6 M10x1.25 screws and 4 M12
screws.
MAX LOAD ON BALL: 100/120 kg
according to the payload (see
“Weights” table in the “Technical
data” section).
After fitting, the screw
holes must be sealed to
prevent exhaust gas from
entering.
WARNING
fig. 162F0N0250m
Existing hole
Existing hole
Existing hole
Standard ball
laden
147-160 DUCATO LUM EN 7ed 6/21/10 2:13 PM Page 158

206
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0117mfig. 220F0N0135mfig. 218
F0N0136mfig. 219
❒take the screwdriver provided from the box and
prise up at the point shown to raise the cap
C-fig. 219;
❒take the tow ring D from the box and screw onto
the threaded pin fig. 219.
The rear ring B-fig. 220 is located at the point shown in
the diagram. For activation / deactivation, proceed as follows:
❒Open the flap A and remove it as illustrated
in fig. 217;
❒turn the locking knob B anticlockwise and remove it
fig. 217 to allow the removal of the compartment
fig. 218;
F0N0134mfig. 217
173-206 DUCATO LUM EN 8ed 27-10-2010 15:45 Pagina 206

280
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
Gearbox
– using the manual
gearbox ................................ 150
General warnings ..................... 2
Glove compartment ................ 91
Handbrake ................................149
Handbrake lever ...................... 149
Hazard lights ............................. 85
Headlight alignment
corrector ................................ 113
Headlight washers
– control ................................. 79
– maintenance ........................ 227
Headlights ..................................113
– adjusting headlights
abroad .................................. 114
– beam orientation ............... 113
– bulb replacement ............... 188
– headlight alignment
corrector ............................. 113Headlights
(warning for cleaning) ........... 229
Headrests .................................. 46
Heated rear window ............... 86
Heating and ventilation ........... 51
– automatic climate
control ................................. 60
– controls ................................ 52
– front window rapid
defrosting/demisting .. 54-57-65
– heated rear window
and external rear view
mirror defrosting/
demisting .....................54-59
– interior air recirculation ... 55
– passenger compartment
air vents ............................... 52
– manual climate control ...... 55
Heavy use of the vehicle
servicing ................................... 212
Hill Holder system .................. 117
Identification plates ................. 233
– body paintwork .................. 232
– identification data ............... 234
Ignition switch .......................... 12
– steering lock ........................ 13
In an emergency ....................... 173
Installation of electrical/
electronic devices .................. 125
Installing the tow hook ...........155
– assembly diagrams ..... 157-158
Instrument panel ...................... 14
Interior fittings ......................... 90
Interiors (maintenance) .......... 222
Isofix (child seat) ...................... 138
Keys ........................................... 5
– Code card ........................... 5
– key with remote control .. 6
– key without remote
control ................................. 8
– replacing the battery ......... 8
277-284 DUCATO LUM EN 9ed 15-04-2011 8:32 Pagina 280