2009 FIAT DOBLO reset

Button
▲
¯˙▼
1 2 3 4 5 6
RADIO FUNCTIONS
Radio station search:
– Automatic search
– Manual search
Programming current radio station
Stored station recall
Mode
Automatic search: pressing buttons ¯or ˙
(long press for fast forward)
Manual search: pressing buttons ▲or ▼
(long press for fast forward)
Long button press for memory preset 1 to 6
Short button press for
memory preset 1 to 6
7
INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER
QUICK
GUIDE
Button
MUTE
AUDIO
MENU
GENERAL FUNCTIONS
Volume activation/deactivation (Mute/Pause)
Audio adjustments: low tones (BASS), high tones (TREBLE),
left/right balance (BALANCE), front/rear balance (FADER)
Advanced functions adjustment
Volume adjustment
Mode
Short button press
Menu activation: short button press
Selection of type of adjustment: pressing buttons ▲or ▼
Adjustment of values: pressing buttons ¯or ˙
Menu activation: short button press
Selection of type of adjustment: pressing buttons ▲or ▼
Adjustment of values: pressing buttons ¯or ˙
Left/right rotation of turning control
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 7

INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER
10
QUICK
GUIDE
❒FM Multipath detector;
❒manual programming of 30 stations:
18 on FM band (6 on FM1, 6 on FM2,
6 on FMT), 12 on MW band;
❒automatic storage (AUTOSTORE func-
tion) of 6 stations in the dedicated FM
band;
❒SPEED VOLUME function: automatic
volume adjustment based on vehicle
speed;
❒automatic Stereo/Mono selection.CD section
❒Direct disc selection;
❒track selection (forward/backward);
❒fast track search (forward/backward);
❒CD Display function: display of disc
name/time elapsed since start of the
track;
❒playing audio CD, CD-R and CD-RW. GENERAL INFORMATION
The radio has the following functions:
Radio section
❒PLL tuning with frequency bands
FM/AM/MW;
❒RDS (Radio Data System) with TA (traf-
fic information) – TP (traffic programs)
– EON (Enhanced Other Network)
– REG (regional programs) functions;
❒AF: alternative frequency search selec-
tion in RDS mode;
❒emergency alarm presetting;
❒automatic/manual station tuning;On multimedia CDs, besides
audio tracks, there are data
tracks too. Playing this type
of CD could cause hissing at a volume
that could jeopardise road safety as
well as causing damage to the final
stages and the speakers.
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 10

INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER
14
QUICK
GUIDE
LOUDNESS FUNCTION
The Loudness function improves the vol-
ume of the sound whilst listening at low
volumes, increasing the bass and treble.
To activate/deactivate the function, select
the Loudness setting of the AUDIO menu
using the ¯or ˙button. The function sta-
tus (on or off) is shown on the display for
a few seconds by the words Loudness On
or Loudness Off.
AUDIO DELAY FUNCTION
This function lets you select the the best
acoustics for the front passengers.
To activate the function select the setting
AUDIO DELAY from the AUDIO menu
and using the buttons ¯or ˙select one
of the following settings:
❒ OFF (function off)
❒ Driver Left (optimisation for the front
left passenger)
❒ Driver Right (optimisation for the front
right passenger)
❒ Front (optimised for both front pas-
sengers).PRESET/USER*/
CLASSIC/ROCK/JAZZ
functions (equalizer on/off)
The built-in equalizer can be activated/
deactivated. When the equalizer function
is off, the audio settings can only be
changed by adjusting the bass and treble
settings, whereas when the function is
on, the acoustic curves can be adjusted.
To turn off the equalizer, select the “EQ
Preset” function using the ¯or ˙buttons.
To turn on the equalizer, use the ¯or ˙
buttons to select one of the adjustments:
❒ “FM/AM/CD...EQ User” (adjustment of
7 equalizer bands that can be changed
by the user);
❒“Classic” (optimum predefined adjust-
ment of equalizer for listening to clas-
sical music);
❒“Rock” (optimum predefined adjust-
ment of equalizer for listening to rock
and pop music);
❒“Jazz” (optimum predefined adjustment
of equalizer for listening to jazz music);
When one of the equalizer adjustments is
activated the letters “EQ” light up. FADER ADJUSTMENT
Proceed as follows:
❒ Use button ▲or ▼to set the “Fader”
in the AUDIO menu;
❒ press button ¯to increase the sound
coming from the rear speakers or but-
ton ˙to increase the sound coming
from the front speakers.
By pressing the buttons briefly there is
a gradual change in steps. By pressing them
down longer, the levels will change quickly.
Select “¯0 ˙” to set the same level for
the front and rear audio outputs.
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 14

15
INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
*USER EQ SETTINGS function
(equalizer settings only if the USER
setting has been selected)
To set a customized equalizer adjustment,
set either the ▲or ▼
button to User and
press the MENU button.
A graph with 7 bars will appear on the
display, where each bar represents a fre-
quency. Select the bar to adjust using
buttons ¯or ˙; the bar selected will
start to flash and can be adjusted using
buttons ▲or ▼.
Press the AUDIO button again to mem-
orize the setting. The display will show
the source activated at the time followed
by the word User. If the mode is, for ex-
ample, FM, then the display will show
“FM EQ User”.MENU
MENU button functions
Press the MENU button briefly to activate
the Menu function. The display will show
the first menu item that can be adjusted
(AF) (AF Switching On on the display).
To scroll through the Menu functions use
button ▲or ▼
. To change the setting of
the selected function, use the buttons
¯or ˙.
The current status of the function selected
will be shown on the display.
The functions managed by the Menu are:
❒AF SWITCHING (ON/OFF);
❒TRAFFIC INFORMATION (ON/OFF);
❒REGIONAL MODE regional programs
(ON/OFF);❒MP3 DISPLAY (CD MP3 display setting);
❒SPEED VOLUME (automatic volume
control based on speed);
❒EXTERNAL AUDIO (telephone volume
adjustment);
❒RADIO OFF (off mode);
❒SYSTEM RESET.
Press the MENU button again to exit the
Menu function.
IMPORTANT The AF SWITCHING,
TRAFFIC INFORMATION and REGION-
AL MODE adjustments are only possible
on FM.
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 15

INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER
16
QUICK
GUIDE
AF SWITCHING function
(alternative frequency search)
The radio can operate in two different
modes in the RDS system:
❒“AF Switching On”: search for alterna-
tive frequencies activated (the letters
“AF” appear on the display);
❒“AF Switching Off”: search for alterna-
tive frequencies not activated.
Proceed as follows to switch the function
on/off:
❒press the MENU button and select
“AF Switching On”;
❒press the ¯/ ˙buttons to turn the
function on/off.
With the function activated, the radio au-
tomatically tunes into the station with the
strongest signal broadcasting the same
program. While driving, you can contin-
ue to listen to the same station without
having to change the frequency when you
change zones.
Obviously, it must be possible to receive
the station that you are listening to in the
area you are driving through.If the AF function is activated, “AF” will
light up on the display.
If the AF function has been activated and
the radio is not able to receive the tuned
station, the radio activates the automatic
search, during which “FM Search” appears
on the display (only for top of the range
radios).
With the AF function deactivated, the re-
maining RDS functions, such as the display
of the station name, still remain active.
The AF function can only be activated on
FM bands.TRAFFIC INFORMATION
function (traffic information)
Some stations on the FM band (FM1, FM2
and FMA) can transmit information about
traffic conditions. In this case the letters
“TA” will appear on the display.
Proceed as follows to switch the TA
function on/off:
❒press the MENU button and select
“Traffic Info”;
❒press the ¯/ ˙buttons to turn
the function on/off.
If the TA function is activated, “TA” will
light up on the display.
IMPORTANT If the TA function is acti-
vated with an audio source other than
Tuner (Radio) (CD, MP3, Telephone or
Mute/Pause), the radio can carry out an
automatic search and therefore it is pos-
sible, when reactivating the Tuner (Radio)
source, that the frequency tuned into will
be different from the one set previously.
With the TA function, it is possible to:
❒search only for RDS stations that
broadcast on the FM band, which are
enabled to transmit traffic information;
❒receive traffic information even if the
CD player is on;
❒receive traffic information at a minimum
preset volume even with the radio vol-
ume zeroed.
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 16

19
INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
EXTERNAL AUDIO function
(telephone volume adjustment)
This function makes it possible to adjust
(settings from 1 to 40), by turning the con-
trol fig. 1or pressing the ¯/ ˙buttons
or exclude (OFF setting) the volume of the
Telephone, the Blue&Me™(except the
Media Player function).
The display shows the current function
status:
❒“EXT Audio Off”: function deactivated.
❒“EXT Audio Volume 23”: function acti-
vated with volume setting 23.RADIO OFF function
(on and off mode)
This function is used to select the mode of
turning off the radio between two differ-
ent procedures. To activate the function,
use the ¯or ˙buttons.
The selected mode will appear on the
display:
❒“00 MIN”: the radio turns off automat-
ically in connection with the ignition
key; the radio turns off automatically as
soon as the key is turned to the STOP
position;
❒“20 MIN”: the radio turns off indepen-
dently from the ignition key; the radio
remains on for a maximum period of
20 minutes after the key has been
turned to the STOP position.
SYSTEM RESET function
This function is used to restore all settings
to the factory values. The options are:
❒NO: no restore intervention;
❒YES: the default parameters are restored.
The display will show Resetting during
this operation. At the end of the opera-
tion, the source does not change and the
previous situation will be displayed.TELEPHONE PREPARATION
If a hands-free kit is installed on the car, when
there is an incoming phonecall the radio au-
dio will be connected to the telephone out-
put. The telephone volume is always fixed,
but it can be adjusted during a conversation
using the rotating control fig. 1.
The fixed telephone audio volume can be
adjusted using the “EXT Audio” function
in the Menu. The word PHONE will ap-
pear on the display during the deactivation
of the audio for the phonecall.
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 19

INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER
20
QUICK
GUIDE
ANTI-THEFT PROTECTION
The radio is equipped with an anti-theft
protection system based on the exchange
of information between the radio and the
electronic control unit (Body Computer)
on the vehicle.
This system guarantees maximum securi-
ty and avoids the secret code having to be
entered every time after the radio power
supply is disconnected.
If the outcome of the check is positive, the
radio will start to work, whilst if the codes
compared are not the same or if the elec-
tronic control unit (Body Computer) is re-
placed, the equipment will notify the user of
the need to enter the password following
the procedure in the paragraph below.Entering the password
When the radio is switched on, if the pass-
word is requested, the display will show
“Radio code” for about 2 seconds followed
by four dashes “- - - -”.
The password is made up of four numbers
from 1 to 6, each corresponding to one
of the dashes.
To enter the first number, press the button
corresponding to the preset stations (from
1 to 6). Enter the other code numbers in
the same way.
If the four digits are not entered within
20 seconds, the display will show “Enter
code - - - -”. This event is not considered
an incorrect entering of the code.
After entering the fourth digit (within
20 seconds), the car radio will start to work.
If an incorrect code is entered, the radio
will emit a sound and the display will show
“Radio blocked/wait” to notify the user
of the need to enter the correct code.
Each time the user enters an incorrect
code, the waiting time will gradually in-
crease (1 min, 2 min, 4 min, 8 min, 16 min,
30 min, 1h, 2h, 4h, 8h, 16h, 24h) up to
a maximum of 24 hours. The waiting time
will be shown on the display by “Radio
blocked/wait”. After the message disap-
pears, the code entering procedure may
be started again.Code card
This document certifies ownership of the
car radio. The Code Card contains the
model of the radio, the serial number and
the password.
IMPORTANT Keep the Code Card some-
where safe so that the authorities can be
supplied with the relevant information
if the radio is stolen.
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 20

21
INTRODUCTION
FUNCTIONS
AND
ADJUSTMENTS
RADIO
(TUNER)
CD PLAYER
CD MP3
PLAYER QUICK
GUIDE
FREQUENCY BAND
SELECTION
With the Radio mode active, press the
FM or AM button briefly and repeatedly
to select the desired reception band.
Each time the button is pressed the fol-
lowing bands are selected cyclically:
❒pressing the FMas button: “FM1”, “FM2”
or “FMA”;
❒pressing the AM button: “MW”.
Each band is highlighted by the name in the
display. The last station selected on the re-
spective frequency band will be tuned into.
The FM band is divided into sections: FM1,
FM1 or “FMA”; the FMA reception band
is reserved for broadcasters stored auto-
matically using the AutoSTore function.PRESELECTION BUTTONS
The buttons numbered from 1 to 6 are
used to set the following preselections:
❒18 on the FM band FM (6 on FM1, 6 on
FM2, 6 on FMT or “FMA” (on some
versions);
❒12 on the MW band;
To listen to a preset station, select the
desired frequency band and then briefly
press the corresponding preset button
(from 1 to 6).
By pressing the preset button for more
than 2 seconds, the tuned station will be
stored. The storing phase is confirmed by
an acoustic signal. INTRODUCTION
When the radio is turned on the last func-
tion selected before it was switched off is
activated: Radio, CD, CD MP3 or Media
Player (only with Blue&Me™).
To select the Radio function when anoth-
er audio source is being listened to, briefly
press the FMas or AM buttons depending
on the desired band.
Once the Radio mode has been activated,
the display will show the name (RDS sta-
tions only) and the frequency of the se-
lected radio station, the frequency band
selected (e.g. FM1) and the preselect but-
ton number (e.g. P1).
R R
A A
D D
I I
O O

( (
T T
u u
n n
e e
r r
) )
604_39_199 Radio Doblo GB 1ed 17-09-2009 11:51 Pagina 21