2009 FIAT BRAVO Tail light

10
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
THE KEYS
CODE CARD
(for versions/markets, where provided)
Together with the keys you will receive
the CODE card fig. 7to be presented to
Fiat Dealership when requesting additional
keys.
IMPORTANT In order to ensure perfect
efficiency of the electronic devices con-
tained inside the keys, they should never
be exposed to direct sunlight.KEY WITHOUT REMOTE
CONTROL
(for versions/markets, where provided)
The key is fitted with a metal insert
A-fig. 8, operating:
❒the ignition switch
❒doors and tailgate locks
❒the fuel lid locking/unlocking (on ver-
sions featuring fuel filler cap with lock)
❒the safe lock device (only disengage-
ment - for versions/markets, where
provided) All the keys and the CODE
card must be handed over to
the new owner when selling
the car.
fig. 7F0Q0001mfig. 8F0Q0034m
001-022 BRAVO GB:001-022 BRAVO GB 11-11-2009 14:06 Pagina 10

11
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
KEY WITH REMOTE CONTROL
The key is fitted with a metal insert
A-fig. 9, operating:
❒the ignition switch
❒doors and tailgate locks
❒the fuel lid locking/unlocking
❒the safe lock device (only disengage-
ment - for versions/markets, where
provided)
To open/close the metal insert, press but-
ton BButton
Ëfor remote unlocking of doors
and tailgate.
Button
Áfor remote locking of doors and
tailgate.
Button
Rfor remote opening of the tail-
gate. Button Bfor power-assisted open-
ing of the metal insert A.
If locking button
Áis inadver-
tently pressed from the pas-
senger compartment, when
getting out of the car only the doors
being used will unlock; the tailgate will
stay locked. To realign the system,
press again the locking/unlocking but-
tons
Á/Ë.
Button B-fig. 9 should only
be pressed when the key is
away from the body, in particular
from the eyes and from objects that
can be spoilt (e.g. clothes). Make sure
the key can never be touched by oth-
ers, especially children, who may in-
advertently press the button.
WARNING
fig. 9F0Q0255m
Opening the doors and the tailgate
Briefly press button
Ëfor remote un-
locking of doors and tailgate and simulta-
neous alarm (for versions/markets, where
provided) deactivation, timed switching on
of the internal ceiling lights and double
flashing of direction indicators (for ver-
sions/markets, where provided).
Press button
Ëfor more than 2 seconds
to open the windows.
Doors will be unlocked automatically if the
fuel inertial cut-off switch comes into op-
eration.
001-022 BRAVO GB:001-022 BRAVO GB 11-11-2009 14:06 Pagina 11

12
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Closing the doors and the tailgate
Briefly press button
Áfor remote lock-
ing of doors and tailgate and simultaneous
alarm (for versions/markets, where pro-
vided) activation, switching off of the in-
ternal ceiling lights and single flashing of di-
rection indicators.
Press button
Áfor more than 2 seconds
to close the windows. If the button is
briefly pressed twice, the safe lock device
(for versions/markets, where provided) is
activated (see next paragraph “Safe lock
device”).
If one or more doors are open, locking
will not be activated and the central pan-
el led A-fig. 10and direction indicators
will flash rapidly. If only the tailgate is open
the doors will lock.Opening the tailgate by the
remote control
Press button
Rto open the tailgate by
remote control even if the alarm (for ver-
sions/markets, where provided) is on.
Opening the tailgate is accompanied by the
direction indicators flashing twice; clos-
ing is accompanied by a single flash only if
the alarm is on.
Opening the tailgate (with alarm on) will
obtain the deactivation of boot volumet-
ric protection and perimetral sensor.
Closing the tailgate will reactivate boot
volumetric protection and perimetral sen-
sor.
fig. 10F0Q0742m
Leds on central panel
When locking the doors, led A-fig. 10
switches on for about 3 seconds and than
starts flashing (deterrence function).
Once doors are locked, if one or more
doors or the tailgate are not closed cor-
rectly, the led and direction indicators
start flashing quickly.
001-022 BRAVO GB:001-022 BRAVO GB 11-11-2009 14:06 Pagina 12

15
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
The main functions that can be activated with the keys (with or without remote control) are the following:
Door
opening
Key turning
counterclockwise
(driver side) or
clockwise
(passenger side)
(where provided)
Key turning
counterclockwise
(driver side) or
clockwise
Pressing briefly
button Ë
2 flashings
Deterrence led
turning offDoor
closing
Key turning
clockwise
(driver side) or
counterclockwise
(passenger side)
(where provided)
Key turning
clockwise
(driver side) or
counterclockwise
Pressing briefly
button Á
1 flashing
Turned on fixed for
approx. 3 seconds
followed by deter-
rence led flashing
Window
opening
–
–
Prolonged pressing
(> 2 seconds) on
button Ë
2 flashings
Turning off
deterrence ledWindow
closing
–
–
Prolonged pressing
(> 2 seconds) on
button Á
1 flashing
Deterrence led
flashingSafe lock
(for versions/
markets, where
provided)
–
–
Double pressing
on button Á
3 flashings
Double flashing
and then
deterrence led
flashingTailgate
opening
–
–
Press
button R
2 flashings
Deterrent led
flashingType
of key
Key without
remote
control
(for versions/
markets,
where
provided)
Key with
remote
control
Direction
indicators
flashing
(only with key
with remote
control)
Led on
central
dashboard
001-022 BRAVO GB:001-022 BRAVO GB 11-11-2009 14:06 Pagina 15

17
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
HOW TO ACTIVATE THE ALARM
With the doors, bonnet and boot shut and
the ignition key in the STOPposition or
with the key removed, point the key with
remote control in the direction of the car,
then press and release the button
Á.
With the exception of certain markets,
the system sounds a “beep” and the doors
are locked.
Engagement of the alarm is preceded by
a self-diagnostic test. If a fault is detected
the system sounds a further warning
“beep” and the display shows the relevant
message (see section “Warning lights and
messages”).
In this case, switch the alarm system off by
pressing button
Ë, check that the doors,
bonnet and tailgate are properly shut, then
switch the alarm on again by pressing but-
ton
Á.
Otherwise, the door, bonnet or tailgate
that is not shut properly will be excluded
from the alarm system control.If the doors, bonnet and boot are shut
correctly and the control signal is repeat-
ed, the system self-diagnostics has de-
tected a system operating fault. It is there-
fore necessary to contact Fiat Dealership.
IMPORTANT When operating the cen-
tral door locking with the metal insert of
the key, the alarm is not activated.
IMPORTANT The electronic alarm is built
in compliance with the law and regulations
of the different countries.HOW TO DEACTIVATE
THE ALARM
Press button
Ëof the key with remote
control.
The system will react as follows (with the
exception of certain markets):
❒two brief flashes of the direction indi-
cators;
❒two brief “beeps”;
❒door unlocking.
IMPORTANT Operating the central door
locking with the metal insert of the key
will not deactivate the alarm.
001-022 BRAVO GB:001-022 BRAVO GB 11-11-2009 14:06 Pagina 17

28
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Speed Beep (Speed limit)
With this function it is possible to set the
car speed limit (km/h or mph); when this
limit is exceeded the driver is immediate-
ly alerted (see section “Warning lights and
messages”).
To set the speed limit, proceed as follows:
– briefly press button MODE, the display
will show wording (Speed Beep);
– press button
Õor Ôto select activa-
tion (On) or deactivation (Off) of the
speed limit;
– if selecting (On), press button
Õor Ôto select the required speed limit and then
press MODEto confirm.
NoteThe possible setting is between 30
and 200 km/h, or between 20 and 125
mph depending on the unit set previous-
ly (see “Distance unit (Dist. Unit)” para-
graph described later. Every press on but-
ton
Õ/Ôincreases/decreases by 5 units.
Keeping the button Õ/Ôpressed obtains
the automatic fast increase or decrease.
When you are near the required setting
complete adjustment by single presses.– briefly press button MODEto go back
to the menu screen or press the button
for long to go back to the standard screen
without storing settings.
To cancel the setting, proceed as follows:
– briefly press button MODE: (On) will
flash on the display;
– press button
Ô: (Off) will flash on the
display;
– briefly press button MODEto go back
to the menu screen or press the button
for long to go back to the standard screen
without storing settings. Dimmer (Passenger compartment
control light rheostat)
(only with side/taillights on)
With this function it is possible to adjust
brightness of the instrument panel and of
buttons and controls of sound system and
automatic climate control system (where
provided) according to 8 levels (for ver-
sions/markets, where provided).
To adjust brightness proceed as follows:
– briefly press button MODE, the previ-
ously set level will flash on the display;
– press button
Õor Ôto adjust the
brightness level;
– briefly press button MODEto go back
to the menu screen or press the button
for long to go back to the standard screen
without storing settings.
DISPLAY FUNCTIONS
(see Multifunctional Display or Reconfigurable Multifunctional Display)
023-036 BRAVO GB:023-036 BRAVO GB 11-11-2009 10:51 Pagina 28

56
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
AUTOMATIC HEADLIGHTS
SENSOR (daylight sensor) fig. 48
(for versions/markets, where provided)
It detects the changes of the external light
intensity of the car according to the light
sensitivity set: greater is the sensitivity,
smaller is the amount of external light nec-
essary to control the switching-on of the
exterior headlights. The daylight sensor
sensitivity can be adjusted with the “Set-
up Menu” of the instrument panel.
Activation
Turn the knurled ring to
2A: in this way,
the automatic activation of the
side/taillights and dipped beam headlights
are simultaneously enabled according to
the external luminosity.
During the sensor operation lights can on-
ly be made flashing.
Deactivation
As a result of the sensor deactivation, the
main beam headlights will switch off and,
after about 10 seconds, sidelights will
switch off too.
The light sensor is not able to detect the
fog presence, lights shall therefore be
switched on manually.
fig. 48F0Q0652m
“Cornering lights”
With low beams on at a speed of less than
40 km/h, when the steering wheel is
turned through a large angle or upon ac-
tivation of the direction indicator, a light
(incorporated in the fog lamp) will come
on to expand the angle of night-time visi-
bility on the side to which the vehicle is
turned.
“FOLLOW ME HOME”
DEVICE fig. 47
This function allows the illumination of the
space in front of the car for a preset pe-
riod of time.Activation
With the ignition key at STOPor re-
moved, pull the stalk towards the steering
wheel and operate it within 2 minutes
from when the engine is turned off.
At each single movement of the stalk, the
staying on of the lights is extended by 30
seconds up to a maximum of 210 seconds;
then the lights are switched off automati-
cally.
Each time the lever is operated, the in-
strument panel warning light
3turns
on (together with the message on the dis-
play) (see section “Warning lights and
messages”).
Deactivation
Keep the stalk pulled towards the steer-
ing wheel for more than 2 seconds.
fig. 47F0Q0651m
037-056 BRAVO GB:037-056 BRAVO GB 11-11-2009 10:52 Pagina 56

65
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
FRONT FOG LIGHTS
(for versions/markets, where provided)
To turn front fog lights on, press button
B-fig. 59to activate these lights it is nec-
essary to have the side/taillights switched
on.
Press the button again to turn the lights
off.
fig. 58F0Q0637mfig. 59F0Q0636m
CONTROLS
HAZARD LIGHTS
They turn on by pressing switch
A-fig. 58, regardless of the position of the
ignition key.
When the function is active, warning lights
Îand ¥on the panel blink.
To switch off, press again the button A.
The use of hazard lights is governed by the
Highway Code of the country you are in.
Keep to the rules.
Emergency braking
In the event of emergency braking the
emergency lights automatically turn on and
at the same time the lights
Îand ¥turn
on on the dashboard.
The function automatically turns off when
the emergency braking stops.
This function complies with the current ap-
plicable laws.REAR FOG LIGHTS
To turn rear fog lights on, press button
C-fig. 59, to activate these lights it is nec-
essary to have the dipped beams or front
fog lights switched on.
Press the button again to turn the lights
off.
057-082 BRAVO GB.qxd 11-11-2009 10:53 Pagina 65