2009 DODGE JOURNEY tow

2. Remove and replace the batteries. Avoid touching the
new batteries with your fingers. Skin oils may cause
battery deterioration. If you touch a battery, clean it with
rubbing alcohol.
3. Reposition the access door panel over the battery
opening and snap into place.
General Information
This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:
•This device may not cause harmful interference.
•This device must accept any interference received, includ-
ing interference that may cause undesired operation.
NOTE:Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
If your RKE transmitter fails to operate from a normal
distance, check for these two conditions.
1. A weak battery in the transmitter. The expected life of
the battery is a minimum of three years.
2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.
Battery Replacement
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

the rear windows open, then open the front and rear
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, adjust the sun-
roof opening to minimize the buffeting or open any
window.
LIFTGATE
The liftgate can be unlocked or locked with the Remote
Keyless Entry (RKE) transmitter or by activating the
power door lock switch located on either front door trim
panel.
NOTE:The liftgate cannot be unlocked or locked with
the manual door lock plungers on the door trim panels or
the door lock cylinder on the driver’s door.
To open the unlocked liftgate, squeeze the handle and
pull the liftgate toward you. Gas props will raise and
support the liftgate in the open position. NOTE:
Because the gas pressure drops with tempera-
ture, it may be necessary to assist the props when
opening the liftgate in cold weather.
Liftgate Release
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!
•A lap belt worn too high can increase the risk of
internal injury in a collision. The belt forces won’t be
at the strong hip and pelvic bones, but across your
abdomen. Always wear the lap belt as low as pos-
sible and keep it snug.
• A twisted belt can’t do its job as well. In a collision,
it could even cut into you. Be sure the belt is straight.
If you can’t straighten a belt in your vehicle, take it to
your authorized dealer and have it fixed.
5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor
will withdraw any slack in the belt. 6. To release the belt, push the red button on the buckle.
The belt will automatically retract to its stowed position.
If necessary, slide the latch plate down the webbing to
allow the belt to retract fully.
WARNING!
A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do
not disassemble or modify the system. Seat belt
assemblies must be replaced after a collision if they
have been damaged (bent retractor, torn webbing,
etc.).
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45
2

you will prefer a higher position. When you release the
anchorage try to move it up and down to make sure that
it is locked in position.
In the rear seat, move toward the center of the seat to
position the belt away from your neck.
Lap/Shoulder Belt Untwisting Procedure
Use the following procedure to untwist a twisted lap/
shoulder belt.
1. Position the latch plate as close as possible to the
anchor point.
2. At about 6 to 12 in (15 to 30 cm) above the latch plate,
grasp and twist the belt webbing 180 degrees to create a
fold that begins immediately above the latch plate.
3. Slide the latch plate upward over the folded webbing.
The folded webbing must enter the slot at the top of the
latch plate.4. Continue to slide the latch plate up until it clears the
folded webbing.
Seat Belt Pretensioners
The driver and front passenger’s seat belts are equipped
with pretensioning devices that are designed to remove
any slack from the seat belt systems in the event of a
collision. These devices improve the performance of the
seat belt by assuring that the belt is tight around the
occupant early in a collision. Pretensioners work for all
size occupants, including those in child restraints.
NOTE:
These devices are not a substitute for proper seat
belt placement by the occupant. The seat belt must still be
worn snugly and positioned properly.
The pretensioners are triggered by the Occupant Re-
straint Controller (ORC). Like the front airbags, the
pretensioners are single use items. After a collision that is
severe enough to deploy the airbags and pretensioners,
both must be replaced.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47
2

hook for attachment to the tether strap anchor and a
means of adjusting the tension of the strap.
You will first loosen the adjusters on the lower straps and
on the tether strap so that you can more easily attach the
hooks or connectors to the vehicle anchors. Next, attach
the lower hooks or connectors over the top of the
seatcover material. Then attach the tether strap to the
anchor directly behind the seat where you are placing the
child restraint, being careful to route the tether strap to
provide the most direct path between the anchor and the
child restraint, preferably between the head restraint
posts underneath the head restraint. Finally, tighten all
three straps as you push the child restraint rearward and
downward into the seat, removing slack in the straps
according to the child restraint manufacturer’s instruc-
tions.NOTE:
•Ensure that the tether strap does not slip into the
opening between the seatbacks as you remove slack in
the strap.
•When using the LATCH attaching system to install a
child restraint, please ensure that all seat belts not
being used for occupant restraints are stowed and out
of reach of children. It is recommended that before
installing the child restraint, buckle the seat belt so the
seat belt is tucked behind the child restraint. This
should stow the seat belt out of the reach of an
inquisitive child. Remind all children in the vehicle
that the seat belts are not toys and that they should not
play with them. In addition, never leave unattended
children in the vehicle.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Storage ..............................180
▫ Beverage Cooler/Storage Compartment —
If Equipped .........................180
▫ Instrument Panel Storage Compartment —
If Equipped .........................182
▫ Center Console Storage .................183
▫ Flip ’n Stow™ Front Passenger Seat Storage —
If Equipped .........................184
▫ Second-Row Passenger Seat Temporary
Storage Bin ..........................185
▫ Second-Row Map Pocket And Grocery
Retainers — If Equipped ................186 ▫
In-Floor Storage Bin With Removable Liner . . . 186
 Cargo Area Features .....................188
▫ Rechargeable Flashlight — If Equipped ......188
▫ Cargo Management System ..............188
 Rear Window Features ...................193
▫ Rear Window Wiper/Washer — If Equipped . . 193
▫ Rear Window Defroster — If Equipped ......195
 Roof Luggage Rack — If Equipped ..........196
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87
3

MIRRORS
Inside Day/Night Mirror
Adjust the mirror to center on the view through the rear
window. A two-point pivot system allows for horizontal
and vertical mirror adjustment.
Annoying headlight glare can be reduced by moving the
small control under the mirror to the night position
(toward the rear of the vehicle). The mirror should be
adjusted while set in the day position (toward the wind-
shield).
Manual Rearview Mirror
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3. Pull the sun visor toward the inside rearview mirror to
extend it.
PARKVIEWREAR BACKUP CAMERA — IF
EQUIPPED
The Parkview Rear Backup Camera captures live video
of the area behind the vehicle. The live video displays on
the radio’s display screen when backing up your vehicle.
NOTE: Refer to “Setting Display Properties,” under
“System Settings” in the Navigation User’s Manual for
navigation screen brightness adjustment instructions.
To operate the Rear Backup Camera:
1. Start the engine.
2. Move the shift lever into REVERSE.
3. Wait one to two seconds and the video will display on
the radio’s display screen. NOTE:
The video will only display while the shift lever
is in REVERSE.
WARNING!
Drivers must be careful when backing up a vehicle,
even when using the Rear Backup Camera. Always
check carefully for pedestrians, animals, other ve-
hicles, obstructions, and blind spots before backing
up a vehicle. You are responsible for the safety of
your surroundings and must continue to pay atten-
tion while backing up a vehicle. Failure to do so can
result in serious injury or death.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE