2009 CHERY TIGGO wheel torque

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Antilock Brake System (ABS) Bleeding Procedure
ABS Bleeding Information
WARNING!
When bleeding the brake system, wear safety glasses. A clear bleed tube must be attached to the bleeder
screws and submerged in a clear container filled partially. Direct the flow of brake fluid away from yourself and
the painted surfaces of the vehicle. Brake fluid at high pressure may come out of the bleeder screws when
opened.
CAUTION:
Before removing the master cylinder cap, wipe it clean to prevent dirt and other foreign matter
from dropping into the master cylinder reservoir. Use brake fluid or an equivalent from a fresh,
tightly sealed container. Brake fluid must conform to DOT 4 specifications.
NOTE :
During the brake bleeding procedure, be sure the brake fluid level remains close to theMAXlevel in the master
cylinder fluid reservoir. Check the fluid level periodically during the bleeding procedure and add brake fluid as
required.
NOTE :
Do not pump the brake pedal at any time while having a bleeder screw open during the bleeding process. This will
only increase the amount of air in the system and make additional bleeding necessary. Do not allow the master
cylinder reservoir to run out of brake fluid while bleeding the system. An empty reservoir will allow additional air into
the brake system. Check the fluid level frequently and add fluid as needed. The following wheel circuit sequence for
bleeding the brake hydraulic system should be used to ensure adequate removal of all trapped air from the hydraulic
system.
ABS Bleeding Instructions
When bleeding the ABS system, the following bleeding sequence must be followed to ensure complete and adequate
bleeding:
1. Make sure all hydraulic fluid lines are installed and properly torqued.
2. Connect the X-431 scan tool to the diagnostics connector.
3. Using the scan tool, check to make sure the ABS module does not have any fault codes stored. If it does, clear them.
4. Bleed the base brake system (See Manual Brake Bleeding in Section 12 Brake).
NOTE :
Pressure bleeding is recommended to bleed the base brake system to ensure all air is removed from the brake
system.
5. Using the scan tool, access ABS bleedingfunction. Follow the instructions displayed. When finished, discon-
nect the scan tool and proceed.
6. Bleed the base brake system a second time. Check brake fluid level in the reservoir periodically to prevent emptying, causing air to enter the hydraulic system.
7. Fill the master cylinder fluid reservoir to the MAXlevel.
8. Test drive the vehicle to be sure the brakes are operating correctly and that the brake pedal does not feel spongy.
12–76Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
The parking brakes consist of the following components:
•Hand-operated parking brake lever
• Parking brake cables (one each side)
• Parking brake controls
Operation
All vehicles are equipped with a center-mounted, hand-operated parking brake lever mounted between the front
seats. A tensioner is built into the equalizer mounted on the end of the lever’s output cable. There is an individual
parking brake cable for each rear wheel that joins a parking brake cable equalizer, attached to the parking brake
lever, to the rear parking brakes. The parking brake cables are made of flexible steel cable.
Specifications
Torque Specifications
DESCRIPTION TORQUE (N·m)
Parking Brake Cable Routing Clamp Bolt 12
Parking Brake Cable Bracket Bolts 12
Parking Brake Lever Nuts 30
Wheel Mounting Nuts 110
Special Tools
Brake Measuring Gauge
J21177-A
12–80Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
All models are equipped with a common HVAC housing assembly that combines A/C and heating capabilities into a
single unit mounted within the passenger compartment. The HVAC housing assembly consists of three separate
housings:
•HVAC housing — The HVAC housing is mounted to the dash panel behind the instrument panel and contains
the A/C evaporator. The HVAC housing has mounting provisions for the air inlet housing, blower motor and the
air distribution housing.
• Air distribution housing — The air distribution housing is mounted to the rear of the HVAC housing and con-
tains the heater core, blend-air and mode-air doors and door linkage.
• Air inlet housing — The air inlet housing is mounted to the passenger side end of the HVAC housing. The air
inlet housing contains the recirculation-air door and actuator.
Operation
The A/C system is designed for the use of a non-CFC, R-134a refrigerant and uses an A/C evaporator to cool and
dehumidify the incoming air prior to blending it with the heated air. Temperature control determines the discharge air
temperature by operating the temperature control cable, which moves the blend-air door. This allows an almost
immediate control of the output air temperature of the system. The mode door cable operates the mode-air doors
which direct the flow of the conditioned air out the various air outlets, depending on the mode selected. When
equipped with A/C, the recirculation door actuator operates the recirculation-air door which closes off the fresh air
intake and recirculates the air already inside the vehicle. The electric recirculation door actuator and the blower motor
are connected to the vehicle electrical system by the instrument panel wire harness. The blower motor controls the
velocity of air flowing through the HVAC housing assembly by spinning the blower wheel within the HVAC housing at
the selected speed by use of the blower motor resistor, which is around the blower motor.
The air distribution housing must be removed from the HVAC housing and disassembled for service of the blend-air
and mode-air doors. The air inlet housing must be removed from the HVAC housing and disassembled for service of
the recirculation-air door. The HVAC housing must be removed from the vehicle and disassembled for service of the
A/C evaporator.
Specifications
Torque Specifications
DESCRIPTION TORQUE (N·m)
All General Service Screws 2
Evaporator Bolts 4
Expansion Valve Bolts 10
Pipeline Stent 4
Refrigerant Lines To A/C Accumulator 6
Condenser Bolts 6
Refrigerant Lines To A/C Compressor Bolt 30
Refrigerant Lines 10
Refrigerant Lines To A/C Evaporator Bolt 25
13–26Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Front Strut, Front Suspension..................10-21
Front Sub-Frame Assembly, Front Suspension .......10-17
Front Suspension ........................... 10-1
Front Wheel Alignment, Alignment ...............10-44
Front Wheel Speed Sensor, Antilock Brakes .........12-77
Front Windshield, Body Exterior ................15-219
Front Wiper Arm, Body Exterior ................15-240
Front Wiper Link, Body Exterior ................15-241
Front Wiper Motor, Body Exterior ...............15-238
Fuel Delivery System ..........................4-1
Fuel Door, Body Exterior ..................... 15-200
Fuel Door, Body Exterior ........................200
Fuel Filter, Fuel Delivery System .................4-18
Fuel Injector Rail, Fuel Delivery System ............4-19
Fuel Injector, Fuel Delivery System ................4-20
Fuel Pressure Regulator - With Mitsubishi 2.4L Engine, Fuel Delivery System ..................4-23
Fuel Pressure Relief Procedure, Fuel Delivery System . . . 4-15
Fuel Pump, Fuel Delivery System .................4-15
G
Gear Selector & Shifter Assembly, 5-Speed Manual
Transaxle ............................... 8-264
General Information, 1.6L & 1.8L Engine Controls ......3-3
General Information, 1.6L & 1.8L Engine Mechanical ....2-3
General Information, 2.0L Engine Controls ..........3-229
General Information, 2.0L Engine Mechanical .........2-77
General Information, 2.4L Engine Controls ..........3-442
General Information, 2.4L Engine Mechanical ........2-151
General Information, 5-Speed Manual Transaxle ......8-247
General Information, Air Distribution ..............13-26
General Information, Airbag System ...............14-2
General Information, Alignment .................10-39
General Information, Antilock Brakes .............12-35
General Information, Base Brakes ................12-2
General Information, Body Interior ..............15-104
General Information, Charging System .............5-12
General Information, Clutch System ..............8-317
General Information, Cooling System ...............6-2
General Information, DP0 Automatic Transaxle .........8-3
General Information, Drive Shaft (4x4) .............9-25
General Information, Evaporative Emissions .........3-577
General Information, Exhaust System ...............7-2
General Information, F4A4 Automatic Transaxle ......8-144
General Information, Front Axle ...................9-2
General Information, Front Differential .............8-308General Information, Front Suspension
.............10-2
General Information, Fuel Delivery System ...........4-2
General Information, Ignition Control .............3-566
General Information, Interactive Torque Management (ITM) System (4x4) ...............9-17
General Information, Manual Temperature Control .....13-2
General Information, Parking Brake ..............12-80
General Information, Power Steering Pump .........11-32
General Information, Rear Axle ...................9-9
General Information, Rear Suspension ............10-26
General Information, Seat Belt System ............14-51
General Information, Starting System ...............5-2
General Information, Steering Column .............11-9
General Information, Steering Gear ...............11-19
General Information, Steering System ..............11-2
General Information, System Controls .............13-19
General Information, System Plumbing ............13-33
General Information, T

ransfer Case (4x4)..........8-327
General Information, Vehicle Fuse Box Information ....16-38
General Information, Vehicle Ground Distribution .....16-28
General Information, Vehicle Power Distribution ......16-13
General Information, Vehicle Wiring Harness Layout . . . 16-45
General Information, Wheels and Tires ............10-48
General Information, Wiring Information ............16-2
Generator, Charging System ....................5-17
Grille, Body Exterior ........................ 15-201
Grille, Body Exterior ...........................201
H
Headlamp, Body Exterior ..................... 15-191
Headliner, Body Interior ...................... 15-15
Heated Seat Element, Body Interior ..............15-109
Heated Seat Switch, Body Interior ..............15-109
Heater Core, System Plumbing .................13-47
High Mounted Stop Lamp, Body Exterior ..........15-197
Hood Release Cable, Body Exterior ..............15-203
Hood, Body Exterior ........................ 15-202
Hood, Body Exterior ...........................202
Horn, Body Exterior .................. 15-206, 15-208
How To Locate Electrical Schematics In The Service Manual, Electrical Information ............1-25
How To Read Electrical Schematics, Electrical Information .............................. 1-21
How To Use This Manual, Service Information ........1-2
HVAC Housing, Air Distribution .................13-29
INDEX
AI-4

Downloaded from www.Manualslib.com manuals search engine On-Vehicle Service, Interactive Torque Management (ITM)System (4x4) ............................. 9-21
On-Vehicle Service, Manual Temperature Control .....13-15
On-Vehicle Service, Parking Brake ...............12-84
On-Vehicle Service, Power Steering Pump ..........11-34
On-Vehicle Service, Rear Axle ...................9-12
On-Vehicle Service, Rear Suspension .............10-30
On-Vehicle Service, Seat Belt System .............14-52
On-Vehicle Service, Starting System ................5-7
On-Vehicle Service, Steering Column .............11-12
On-Vehicle Service, Steering Gear ...............11-21
On-Vehicle Service, Steering System ..............11-6
On-Vehicle Service, System Controls .............13-24
On-Vehicle Service, System Plumbing .............13-37
On-Vehicle Service, Transfer Case (4x4) ...........8-328
On-Vehicle Service, Wheels and Tires .............10-51
Output Gear For Reverse Gear, 5-Speed Manual Transaxle ......................... 8-296
Output Shaft, 5-Speed Manual Transaxle ...........8-287
Outside Mirror, Body Exterior ..................15-214
Oxygen Sensor, 1.6L & 1.8L Engine Controls .......3-218
Oxygen Sensor, 2.0L Engine Controls .............3-428
Oxygen Sensor, 2.4L Engine Controls .............3-533
P
Paint Codes, Body Exterior ...................15-215
Paint, Body Exterior ........................ 15-215
Parking Brake ............................. 12-79
Parking Brake Cable, Parking Brake ..............12-85
Parking Brake Lever, Parking Brake ..............12-84
Parking Brake Shoes, Parking Brake ..............12-86
Pedal Pad, Body Interior ...................... 15-14
Pistons, 1.6L & 1.8L Engine Mechanical ............2-53
Pistons, 2.0L Engine Mechanical ................2-126
Pistons, 2.4L Engine Mechanical ................2-221
Positive Battery Cable, Starting System .............5-8
Power Brake Booster - LHD, Base Brakes ..........12-14
Power Brake Booster - RHD, Base Brakes ..........12-16
Power Fuse Box, Vehicle Fuse Box Information ......16-38
Power Outlet, Body Interior .................... 15-93
Power Steering Filling and Flushing, Steering System . . . 11-6
Power Steering Fluid Reservoir, Power Steering Pump ........................... 11-36
Power Steering Pressure and Return Lines - 1.6L & 1.8L & 2.0L, Power Steering Pump . . 11-37
Power Steering Pressure and Return Lines - 2.4L, Power Steering Pump ........................... 11-39
Power Steering Pump ....................... 11-31Power Steering Pump - 1.6L & 1.8L & 2.0L,
Power Steering Pump ...................... 11-34
Power Steering Pump - 2.4L, Power Steering Pump . . . 11-35
Power Window Motor, Body Interior .............15-100
Power Window Switch, Body Interior ............15-100
Power Window, Body Interior ..................15-96
Proper Service Practices, Service Information .........1-5
R
Radiator Support, Body Exterior................15-216
Radiator Support, Body Exterior ...................216
Radiator, Cooling System ...................... 6-17
Radio, Body Interior ......................... 15-8
Rear Axle ..................................9-8
Rear Axle Assembly (4x4), Rear Axle ..............9-13
Rear Brake Backing Plate, Base Brakes ............12-23
Rear Brake Caliper, Base Brakes ...........12-19, 12-30
Rear Brake Pads, Base Brakes ..................12-25
Rear Brake Rotor, Base Brakes .................12-22
Rear Coil Spring, Rear Suspension ...............10-33
Rear Combination Lamp Assembly, Body Exterior ....15-190
Rear Crankshaft Oil Seal, 1.6L & 1.8L Engine Mechanical .............................. 2-27
Rear Crankshaft Oil Seal, 2.0L Engine Mechanical ....2-100
Rear Crankshaft Oil Seal, 2.4L Engine Mechanical ....2-179
Rear Door Weatherstrip, Body Exterior ...........15-232
Rear Door, Body Exterior .................... 15-173
Rear Fog Lamp, Body Exterior .................15-193
Rear Hub and Bearing, Rear Axle ................9-12
Rear Intermediate Drive Shaft, Drive Shaft (4x4) ......9-27
Rear Lower Control Arm, Rear Suspension .........10-30
Rear Seat Belt and Pre-Tensioner, Seat Belt System . . . 14-54
Rear Seats, Body Interior .................... 15-107
Rear Shock Absorber, Rear Suspension ...........10-32
Rear Stabilizer Bar Link, Rear Suspension ..........10-32
Rear Suspension ........................... 10-25
Rear Trailing Arm Assembly, Rear Suspension .......10-35
Rear Upper Control Arm, Rear Suspension .........10-31
Rear Wheel Alignment, Alignment ...............10-45
Rear Wheel Speed Sensor, Antilock Brakes .........12-78
Rear Window, Body Exterior ..................15-221
Rear Wiper Arm, Body Exterior ................15-240
Rear Wiper Motor, Body Exterior ...............15-239
Recirculation Door Actuator, System Controls .......13-24
Remote Keyless Entry (RKE) Inoperative, Body Interior ........................... 15-115
Restraints Control Module (RCM), Airbag System .....14-49
INDEX
AI-6