2009 CADILLAC XLR reset

Express Window
Down:Press the front of the window switch to
the second position and release to activate the
express-down feature. To stop the window, briey lift
the switch.
Up:Lift the front of the switch briey to activate the
express-up feature. To stop the window, briey press
the switch.
Express-Up Window
This feature is on both power windows. Press the up
arrow on the switch to the second position to activate the
express-up feature. If you want to stop the window as
it is raising, press the switch again.
Express Window Anti-Pinch Feature
If any object is in the path of the window when the
express-up is active, the window will stop at the
obstruction and auto-reverse to a preset factory position.
Weather conditions such as severe icing may also cause
the window to auto-reverse. The window will return to
normal operation once the obstruction or condition is
removed.
{CAUTION:
If express override is activated, the window will not
reverse automatically. You or others could be
injured and the window could be damaged. Before
you use express override, make sure that all people
and obstructions are clear of the window path.
Express Window Anti-Pinch Override
In an emergency, the anti-pinch feature can be
overridden in a supervised mode. Hold the window switch
all the way down in the express position. The window will
rise for as long as the switch is held. Once the switch is
released, the express mode is re-activated.
In this mode, the window can still close on an object in
its path. Use care when using the override mode.
2-19

The top position is the highest sensitivity setting, level
ve. A single wipe will occur each time the delay adjust
band is turned to a higher sensitivity level to indicate
that the sensitivity level has been increased.
Notice:Going through an automatic car wash with
the wipers on can damage them. Turn the wipers
off when going through an automatic car wash.
The mist and wash cycles operate as normal and are
not affected by the Rainsense function. The Rainsense
system can be overridden at any time by manually
changing the wiper control to low or high speed.
When Rainsense is active, the headlamps will turn
on automatically. If it is dark, they will remain on.
See “Wiper-Activated Headlamps” underExterior
Lamps on page 3-26for more information.
Notice:Do not place stickers or other items on
the exterior glass surface directly in front of
the moisture sensor. Doing this could cause the
moisture sensor to malfunction.Windshield Washer
K(Washer Fluid):The lever on the right side of the
steering column also controls the windshield washer.
There is a button at the end of the lever. To spray
washer uid on the windshield, press the button and
hold it. The washer will spray until you release the
button. The wipers will continue to clear the window
for about six seconds after the button is released and
then stop or return to your preset speed.
{CAUTION:
In freezing weather, do not use your washer until
the windshield is warmed. Otherwise the washer
uid can form ice on the windshield, blocking your
vision.
If the uid in the windshield washer uid reservoir is
low, the message LOW WASHER FLUID will appear
on the Driver Information Center (DIC) display. It
will take 60 seconds after the bottle is relled for this
message to turn off. For information on the correct
washer uid mixture to use, seeWindshield Washer
Fluid on page 6-31andRecommended Fluids and
Lubricants on page 7-11.
3-10

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you are
not using cruise, you might hit a button and go
into cruise when you do not want to. You could be
startled and even lose control. Keep the cruise
control switch off until you want to use cruise
control.
1. Move the cruise control switch to on.
2. Get up to the speed desired.
3. Press the set button at the end of the lever and
release it.
4. Take your foot off the accelerator pedal.
This light
Jappears on the instrument panel cluster
when the cruise control is engaged.
Resuming a Set Speed
If the cruise control is set at a desired speed and
the brake is applied, the cruise control will turn off.
It does not need to be reset
Once the vehicle is going about 25 mph (40 km/h) or
more, move the cruise control switch briey from
RtoS.
The vehicle will go back up to the chosen speed and
stay there.
If the switch is held at resume/accelerate the vehicle
will keep going faster until the switch is released or
the brake is applied. Do not hold the switch at
resume/accelerate, unless you want the vehicle to
go faster.
3-12

Adaptive Cruise Control
If the vehicle has this feature, be sure to read this entire
section before using it.
The system operates on a radio frequency subject to
Federal Communications Commission (FCC) Rules and
with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.Changes or modications to this system by other than
an authorized service facility could void authorization to
use this equipment.
Adaptive Cruise Control is an enhancement to traditional
cruise control and is not a safety system. It allows
you to keep cruise control engaged in moderate traffic
conditions without it having to be constantly reset.
Adaptive Cruise Control uses radar to detect a vehicle
directly ahead in your path, within a distance of
328 ft (100 m), and operates at speeds above
25 mph (40 km/h). When it is engaged by the driver,
the system can apply limited braking or acceleration
of the vehicle, automatically, to maintain a selected
following distance to the vehicle ahead. The vehicle’s
braking during Adaptive Cruise Control is comparable to
a person applying moderate pressure to the vehicle’s
brake pedal. To disengage Adaptive Cruise Control,
apply the brake. If no vehicle is in your path, your
vehicle will react like traditional cruise control.
3-14

Increasing Set Speed While Using Adaptive
Cruise Control
There are two ways to increase the set speed:
Use the accelerator to get to the higher speed.
Press
Tat the end of the lever, then release
the button and the accelerator pedal. The vehicle
will now cruise at the higher speed.
Move the Adaptive Cruise Control switch from
RtoS. Hold it there until the desired set speed
is displayed in the HUD, then release the switch.
To increase the set speed in small amounts, move
the switch briey to resume/increase. Each time
this is done, the vehicle set speed increases
by about 1 mph (1.6 km/h).
Your vehicle will not reach the set speed until the
system determines there is no vehicle in front of you.
At that point, your vehicle speed will increase to the
set speed.
Decreasing Set Speed While Using
Adaptive Cruise Control
PressTon the end of the lever until the lower
desired speed is reached, then release the button.
To slow down in small amounts, briey press
T.
Each this is done, the set speed will be 1 mph (1.6 km/h)
slower.
Resuming a Set Speed
If the brakes are applied while the Adaptive Cruise
Control is at a set speed, this disengages the Adaptive
Cruise Control. But it does not need to be reset.
Once the vehicle reaches about 25 mph (40 km/h) or
more, move the Adaptive Cruise Control switch
briey from
RtoS. Adaptive Cruise Control will be
engaged with the speed selected previously.
3-18

Exterior Lamps
The exterior lamp control is located to the left of the
steering wheel on the multifunction lever.
O(Exterior Lamp Control):Turn the band to operate
the exterior lamps.
There are four positions:
O(Off):Turns off all lamps.
AUTO (Automatic):Sets the exterior lamps to
automatic mode. AUTO mode will turn the exterior
lamps on and off depending on how much light
is available outside the vehicle. Turning the band to
AUTO mode also enables the Adaptive Forward Lighting
system. SeeAdaptive Forward Lighting System on
page 3-28.To override AUTO mode, turn the control to off.
To reset to AUTO mode turn the control to exterior
lamps and then back to AUTO. Automatic mode will also
reset when your vehicle is turned off and then back
on again when the control is left in the AUTO position.
SeeTwilight Sentinel
®on page 3-29.
;(Parking Lamp):Turns on the parking lamps
together with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
The parking brake indicator light will come on and stay
on when the parking lamps are on with the engine
off and the ignition to ACC/ACCESSORY.
5(Headlamps):Turns on the headlamps, together
with the previously listed lamps and lights.
3-26

Battery Run-Down Protection
The vehicle has a feature to help prevent the battery
from being drained, in case the underhood lamp, vanity
mirror lamps, cargo lamps, reading lamps, console,
or glove box lamps are accidentally left on, or something
is left plugged into the accessory power outlet or
cigarette lighter. If any of the accessory lamps are
left on, they will automatically time-out after about
10 minutes. To reset the battery protection, all of the
above lamps must be turned off or the ignition must be
in the ACC/ACCESSORY position.
Head-Up Display (HUD)
{CAUTION:
If the HUD image is too bright, or too high in your
eld of view, it may take you more time to see
things you need to see when it is dark outside.
Be sure to keep the HUD image dim and placed
low in your eld of view.The Head-Up Display (HUD) allows you to see some of
the driver information that appears on the instrument
panel cluster.
The information may be displayed in English or metric
units and appears as an image focused out toward
the front of the vehicle. To change from English to metric
units, seeDriver Information Center (DIC) on page 3-57.
The HUD consists of the following information:
Speedometer
Turn Signal Indicators
High-Beam Indicator Symbol
Tap-Up/Tap-Down Transmission Feature
Check Gages Message
Adaptive Cruise Control Features and Indicators
Radio Features
3-31

Antilock Brake System (ABS)
Warning Light
For vehicles with the
Antilock Brake System
(ABS), this light comes on
briey when the engine
is started.
If it does not, have the vehicle serviced by your
dealer/retailer. If the system is working normally the
indicator light then goes off.
If the ABS light stays on, turn the ignition off. If the light
comes on while driving, stop as soon as it is safely
possible and turn the ignition off. Then start the engine
again to reset the system. If the ABS light stays on,
or comes on again while driving, the vehicle needs
service. If the regular brake system warning light is not
on, the vehicle still has brakes, but not antilock brakes.
If the regular brake system warning light is also on,
the vehicle does not have antilock brakes and there is a
problem with the regular brakes. SeeBrake System
Warning Light on page 3-47.
For vehicles with a Driver Information Center (DIC),
seeDIC Warnings and Messages on page 3-60for all
brake related DIC messages.
StabiliTrak®/Traction Control
System (TCS) Warning Light
The Traction Control
System (TCS)/StabiliTrak
system warning light
comes on briey as the
engine is started.
If it does not, have the vehicle serviced by your
dealer/retailer. If the system is working normally the
indicator lights go off.
If the light stays on, or comes on while driving and
the DIC shows a SERVICE TRACTION SYS or
a SERVICE STABILITRAK message, there is a
problem with the Traction Control System (TCS)
or the StabiliTrak
®system and the vehicle needs
service.
3-48