2009 CADILLAC XLR buttons

Heated and Cooled Seats
The buttons for the heated and cooled seats are located
on the climate control system.
((Heated/Cooled Seat):Press to turn the feature on.
The button on the left controls the driver seat and the
button on the right controls the passenger seat. Each
press of the button will take you to a different setting.
The settings available in order are HI HEAT, LO HEAT,
OFF, HI COOL, LO COOL and OFF. You will be able to
feel the temperature change in a few minutes.
The feature will automatically turn off when the vehicle
is turned off. SeeDual Climate Control System on
page 3-36for more information.
Memory Seat, Mirrors and Steering
Wheel
The vehicle is equipped with a memory package.
The controls are located on the driver seat, and are
used to program and recall memory settings for
the driver seating positions.
1-3

Use the following steps to program each button:
1. Adjust the driver seat including the seatback
recliner, lumbar, both outside mirrors and the
steering wheel to a comfortable position.
2. Press and hold button 1 until two beeps are heard,
then release the button.
A second mirror, seating and steering wheel position
can be programmed by repeating the above steps and
pressing button 2 (for driver 2). Each time a memory
button is pressed and released, a single beep will sound.
Each time button 1 or 2 is pressed and released while
the vehicle is in P (Park), the memory positions will be
recalled after a brief delay. If the vehicle is not in P (Park),
three beeps will be heard and the memory position will
not be recalled.
When the engine is started, the seat, mirrors, and
steering wheel may automatically adjust to their
programmed positions.
To stop recall movement of the memory feature at any
time, press one of the power seat controls, power
mirror control buttons, memory buttons, or power
steering column control.
Two personalized exit positions can be set by rst
recalling the driving position (by pressing 1 or 2), then
positioning the steering wheel and seat in the desired exit
positions and then pressing and holding the exit button
until two beeps are heard. The exit button is locatedbetween buttons 1 and 2. With the vehicle in Park (P),
the exit position for the previously set driver can be
recalled by pressing the exit button.
When you use the keyless access transmitter to
unlock your vehicle, automatic seat and steering wheel
movement to the exit position may occur. The numbers
on the back of the transmitter, 1 and 2, corresponds to
the numbers on the memory buttons.
Further programming for automatic seat and mirror
movement can be done using the Driver Information
Center (DIC).
For programming information, seeDIC Vehicle
Personalization on page 3-72.
Power Reclining Seatbacks
Your seats have power
reclining seatbacks.
1-4

Programming with a Recognized
Transmitter
A new transmitter can be programmed to the vehicle
when there is one recognized transmitter. For vehicles
sold in Canada, two recognized transmitters are
required to program a new transmitter.
1. The vehicle must be off.
2. Both the recognized and new transmitters must be
with you.
3. Insert the vehicle key into the key cylinder located
on the lower rear fascia on the driver side of the
vehicle. SeeTrunk on page 2-14for more
information on the key cylinder.
4. Open the trunk.
5. Turn the key ve times within ve seconds.
6. The Driver Information Center (DIC) displays
READYFORFOB#2,3or4.7. Place the new transmitter in the glove box
transmitter pocket with the buttons facing the
passenger side.
2-7

8. A beep sounds once programming in complete.
The DIC will display READY FOR #3 or 4, or
MAX # FOBS LEARNED.
9. To program additional transmitters, repeat Step 7.
Press Acc. on the ignition switch if programming is
complete.
10. Press
Kon each newly programmed transmitter to
complete the process.
Programming without a Recognized
Transmitter
This procedure requires three ten minutes cycles to
complete the programming process. United States
owners are permitted to program a new transmitter to
their vehicle when a recognized transmitter is not
available. The Canadian immobilizer standard requires
that Canadian owners see their dealer/retailer for
programming new transmitters when two recognized
transmitters are not available.
1. The vehicle must be off.2. Place the new transmitter in the glove box transmitter
pocket with the buttons facing the passenger side.
3. Insert the vehicle key into the key cylinder located
on the lower rear fascia on the driver side of the
vehicle. SeeTrunk on page 2-14for more
information on the key cylinder.
4. Open the trunk.
5. Turn the key ve times within ve seconds.
6. The DIC message displays OFF-ACC TO LEARN.
2-8

7. Press Acc. on the ignition switch.
8. The DIC reads WAIT 10 MINUTES and counts
down to zero.
9. The DIC displays OFF-ACC TO LEARN again.
10. Press Acc. on the ignition switch.
11. Steps 8, 9 and 10 will be repeated two more times.
12. A beep sounds and the DIC reads READY FOR
FOB #1. All previously known transmitter
programming has been erased.
13. A beep sounds once programming in complete.
The DIC displays READY FOR FOB #2.
To program additional transmitters, take
transmitter 1 out of the transmitter pocket
and place transmitter 2 in the pocket.
Up to four transmitters can be programmed.
The DIC then displays MAXIMUM NUMBER
OF FOBS LEARNED and exits the
programming mode.
Press Acc. on the ignition switch to complete the
process.14. Press Acc. on the ignition switch if programming is
complete.
15. Press
Kon each newly programmed transmitter to
complete the process.
Starting the Vehicle with a Low
Transmitter Battery
If the transmitter battery is weak, the DIC may display
NO FOB DETECTED when trying to start the vehicle.
To start the vehicle, place the transmitter in the glove box
transmitter pocket with the buttons facing the passenger
side. Then, with the vehicle in P (Park) or N (Neutral),
press the brake pedal and
/. Replace the transmitter
battery as soon as possible. Change the transmitter
battery if the DIC displays FOB BATTERY LOW.
2-9

To lock or unlock your vehicle from the outside, use the
keyless access transmitter and press the appropriate
lock or unlock button. You may also unlock and open the
door passively when you squeeze the door handle
sensor, as long as you have your transmitter with you.
Passive entry occurs when the door handle sensor
is pressed and the vehicle recognizes your keyless
access transmitter. When the passenger door is opened
rst, the driver door will also become unlocked.
From the inside, use the power door lock buttons
located at the top of the door panel near the window.
SeePower Door Locks on page 2-13for more
information.
To open a door from the inside, press the button in front
of the door handle and push the door open.
If power to the vehicle or the keyless access transmitter
is lost, there are two ways to open the door.
2-11

Location information about the vehicle is only available
if the GPS satellite signals are unobstructed and
available.
The vehicle must have a working electrical system,
including adequate battery power, for the OnStar
equipment to operate. There are other problems OnStar
cannot control that may prevent OnStar from providing
OnStar service at any particular time or place. Some
examples are damage to important parts of the vehicle
in a crash, hills, tall buildings, tunnels, weather or
wireless phone network congestion.
Your Responsibility
Increase the volume of the radio if the OnStar advisor
cannot be heard. If the light next to the OnStar buttons
is red, the system may not be functioning properly.
Press the OnStar button and request a vehicle
diagnostic. If the light appears clear (no light is
appearing), your OnStar subscription has expired and
all services have been deactivated. Press the OnStar
button to conrm that the OnStar equipment is active.
Universal Home Remote
System
The Universal Home Remote System provides a way to
replace up to three hand-held radio-frequency (RF)
transmitters used to activate devices such as garage
door openers, security systems, and home lighting.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
The FCC Grant of Equipment Authorization Certicate
number is KOBGTV06A.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
The Canadian Registration ID number is 3521A-GTV06A.
Changes or modications to this system by other than
an authorized service facility could void authorization to
use this equipment.
2-45

Universal Home Remote System
Operation
On vehicles with this feature there are three round Light
Emitting Diode (LED) indicator lights above the Universal
Home Remote buttons, follow the instructions below.
This system provides a way to replace up to three remote
control transmitters used to activate devices such as
garage door openers, security systems, and home
automation devices.
Do not use this system with any garage door opener
that does not have the stop and reverse feature.
This includes any garage door opener model
manufactured before April 1, 1982.
Read the instructions completely before attempting to
program the transmitter. Because of the steps involved,
it may be helpful to have another person assist with
programming the transmitter.Be sure to keep the original remote control transmitter
for use in other vehicles, as well as, for future
programming. Only the original remote control
transmitter is needed for Fixed Code programming.
The programmed buttons should be erased when the
vehicle is sold or the lease ends. See “Erasing Universal
Home Remote Buttons” later in this section.
Park the vehicle outside of the garage when
programming a garage door. Be sure that people and
objects are clear of the garage door or gate that is being
programmed.Programming Universal Home
Remote — Rolling Code
For questions or help programming the Universal
Home Remote System, call 1-866-572-2728 or go to
learcar2u.com.
Most garage door openers sold after 1996 are Rolling
Code units.
Programming a garage door opener involves
time-sensitive actions, so read the entire procedure
before starting. Otherwise, the device will time out and
the procedure will have to be repeated.
2-46