2009 CADILLAC CTS wheel

{CAUTION:
If something is between an occupant and an airbag,
the airbag might not inate properly or it might force
the object into that person causing severe injury
or even death. The path of an inating airbag
must be kept clear. Do not put anything between an
occupant and an airbag, and do not attach or put
anything on the steering wheel hub or on or near
any other airbag covering.
Do not use seat accessories that block the ination
path of a seat-mounted side impact airbag.
Never secure anything to the roof of a vehicle with
roof-rail airbags by routing a rope or tie down
through any door or window opening. If you do, the
path of an inating roof-rail airbag will be blocked.
When Should an Airbag Inate?
Frontal airbags are designed to inate in moderate to
severe frontal or near-frontal crashes to help reduce the
potential for severe injuries mainly to the driver’s or
right front passenger’s head and chest. However, they
are only designed to inate if the impact exceeds a
predetermined deployment threshold. Deployment
thresholds are used to predict how severe a crash is
likely to be in time for the airbags to inate and
help restrain the occupants.
Whether your frontal airbags will or should deploy is not
based on how fast your vehicle is traveling. It depends
largely on what you hit, the direction of the impact,
and how quickly your vehicle slows down.
1-63

What Makes an Airbag Inate?
In a deployment event, the sensing system sends an
electrical signal triggering a release of gas from
the inator. Gas from the inator lls the airbag
causing the bag to break out of the cover and deploy.
The inator, the airbag, and related hardware are all
part of the airbag module.
Frontal airbag modules are located inside the steering
wheel and instrument panel. For vehicles with
seat-mounted side impact airbags, there are airbag
modules in the side of the front seatbacks closest to the
door. For vehicles with roof-rail airbags, there are
airbag modules in the ceiling of the vehicle, near the
side windows that have occupant seating positions.
How Does an Airbag Restrain?
In moderate to severe frontal or near frontal collisions,
even belted occupants can contact the steering wheel
or the instrument panel. In moderate to severe side
collisions, even belted occupants can contact the inside
of the vehicle.
Airbags supplement the protection provided by safety
belts. Frontal airbags distribute the force of the impact
more evenly over the occupant’s upper body, stopping
the occupant more gradually. Seat-mounted side impact
and roof-rail airbags distribute the force of the impact
more evenly over the occupant’s upper body.
But airbags would not help in many types of collisions,
primarily because the occupant’s motion is not
toward those airbags. SeeWhen Should an Airbag
Inflate? on page 1-63for more information.
Airbags should never be regarded as anything more
than a supplement to safety belts.
1-65

Adding Equipment to Your
Airbag-Equipped Vehicle
Q:Is there anything I might add to or change
about the vehicle that could keep the airbags
from working properly?
A:Yes. If you add things that change the vehicle’s
frame, bumper system, height, front end or side
sheet metal, they may keep the airbag system from
working properly. Changing or moving any parts
of the front seats, safety belts, the airbag sensing
and diagnostic module, steering wheel, instrument
panel, roof-rail airbag modules, ceiling headliner
or pillar garnish trim, front sensors, or airbag wiring
can affect the operation of the airbag system.
In addition, the vehicle has a passenger sensing
system for the right front passenger position, which
includes sensors that are part of the passenger’s
seat. The passenger sensing system may not
operate properly if the original seat trim is replaced
with non-GM covers, upholstery or trim, or with
GM covers, upholstery or trim designed for a
different vehicle. Any object, such as an aftermarket
seat heater or a comfort enhancing pad or device,
installed under or on top of the seat fabric, could alsointerfere with the operation of the passenger sensing
system. This could either prevent proper deployment
of the passenger airbag(s) or prevent the passenger
sensing system from properly turning off the
passenger airbag(s). SeePassenger Sensing
System on page 1-67.
If you have any questions, call Customer
Assistance. The phone numbers and addresses
for Customer Assistance are in Step Two of
the Customer Satisfaction Procedure in this manual.
SeeCustomer Satisfaction Procedure on page 7-2.
Q:Because I have a disability, I have to get
my vehicle modied. How can I nd out whether
this will affect my airbag system?
A:If you have questions, call Customer Assistance.
The phone numbers and addresses for Customer
Assistance are in Step Two of the Customer
Satisfaction Procedure in this manual. See
Customer Satisfaction Procedure on page 7-2.
In addition, your dealer/retailer and the service
manual have information about the location of the
airbag sensors, sensing and diagnostic module and
airbag wiring.
1-73

Remote Keyless Entry (RKE)
System Operation
The Remote Keyless Entry (RKE) transmitter functions
work up to 65 feet (20 m) away from the vehicle.
There are other conditions that can affect the
performance of the transmitter. SeeRemote Keyless
Entry (RKE) System on page 2-5.
Q(Lock):Press to lock all
the doors.
If enabled through the Driver
Information Center (DIC),
the parking lamps may ash
once to indicate locking has
occurred. The horn may
chirp when
Qis pressed
again within ve seconds.
SeeDIC Vehicle
Customization on page 3-72
for additional information.
K(Unlock):Press to unlock the driver door. IfKis
pressed again within ve seconds, all remaining doors
unlock. The interior lamps come on and stay on for
20 seconds or until the ignition is turned on.If enabled through the DIC, the parking lamps ash
twice to indicate unlocking has occurred. SeeDIC
Vehicle Customization on page 3-72.
V(Remote Trunk Release):Press and hold for
about one second to unlock the trunk. The automatic
transmission must be in P (Park) or the manual
transmission must be in Neutral with the parking
brake set.
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The turn signal lamps ash and
the horn sounds three times.
Press and hold
Lfor more than two seconds to activate
the panic alarm. The turn signal lamps ash and the horn
sounds for 30 seconds. The alarm turns off when the
ignition is moved to START or
Lis pressed again.
The ignition must be in LOCK/OFF for the panic alarm
to work.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will be
recalled when using the transmitter labeled “1”, if enabled
through the DIC. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8andDIC Vehicle Customization
onpage 3-72.
2-6

For vehicles with the memory feature, pressKon the
keyless access transmitter to program and recall the
memory settings. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8for more information.
/(Remote Start):Press to operate the remote start
feature. SeeRemote Vehicle Start on page 2-14
for additional information.
G(Trunk):Press and hold for about one second to
unlock the trunk. If the engine is running, the shift lever
must be in P (Park) for an automatic transmission or in
Neutral with the parking brake set for a manual
transmission.
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The horn sounds three times
and the turn signal lamps ash three times.
Press and hold
Lfor three seconds to sound the panic
alarm. The horn sounds and the turn signal lamps ash
for 30 seconds. Press and release
Lagain to stop the
alarm.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it, “1” or “2”.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1 will be
recalled when using the transmitter labeled “1”, if enabled
through the DIC. SeeMemory Seat, Mirrors and Steering
Wheel on page 1-8andDIC Vehicle Customization
onpage 3-72.
Programming Transmitters to the
Vehicle
Only keyless access transmitters programmed to the
vehicle will work. If a transmitter is lost or stolen,
a replacement can be purchased and programmed
through your dealer/retailer. The vehicle can be
reprogrammed so that lost or stolen transmitters no
longer work. Each vehicle can have up to four
transmitters matched to it.
Programming with a Recognized
Transmitter
A new transmitter can be programmed to the vehicle
when there is one recognized transmitter. For vehicles
sold in Canada, two recognized transmitters are required
to program a new transmitter.
1. The vehicle must be off.
2. Both the recognized and new transmitters must be
with you.
3. Insert the vehicle key into the key lock cylinder
located on the outside of the driver door.
2-10

Ignition Positions (Key Access)
The key can be turned to four different positions.
To shift out of P (Park), the ignition must be in the
ON/RUN or ACC/ACCESSORY and the brake pedal
must be applied.
Notice:Using a tool to force the key from its
cylinder could cause damage or break the key. Use
the correct key and turn the key only with your hand.
Make sure the key is all the way in. If it is and you
have a manual transmission vehicle, turn the steering
wheel left and right while you turn the key hard. If
none of this works, then the vehicle needs service.A (LOCK/OFF):This is the only position in which the
key can be inserted or removed. This position locks the
ignition and shifter on automatic transmission vehicles,
and the ignition and steering wheel on manual
transmission vehicles.
B (ACC/ACCESSORY):This position lets you use
things like the radio and the windshield wipers when
the engine is off. This position allows you to turn off
the engine.
C (ON/RUN):This position is for driving. It is the
position the ignition switch returns to after the engine
starts, and the key is released.
To shift the transmission out of P (Park), the ignition
key has to be in ACC/ACCESSORY or ON/RUN.
The battery could be drained if the key is left in the
ACC/ACCESSORY or ON/RUN position with the
engine off. The vehicle might not start if the battery
is allowed to drain for an extended period of time.
D (START):This position starts the engine. When
the engine starts, release the key. The ignition switch
returns to ON/RUN for driving.
A warning tone will sound when the driver door is
opened, the ignition is in ACC/ACCESSORY or
LOCK/OFF and the key is in the ignition.
2-31

Ignition Positions (Keyless Access)
You can turn the ignition control knob to four different
positions.
To shift out of P (Park), ignition must be in the ON/RUN
or ACC/ACCESSORY and the regular brake pedal
must be applied.
Using a tool to force the ignition control knob from its
cylinder could damage it.
Make sure the keyless access transmitter is inside the
vehicle when trying to turn the ignition control knob.A (LOCK/OFF):The ignition control knob cannot be
removed from the vehicle. The keyless access
transmitter must be inside the vehicle to start the
engine. This position locks the ignition and shifter on
automatic transmission vehicles, and the ignition
and steering wheel on manual transmission vehicles.
B (ACC/ACCESSORY):This position allows you to use
things like the radio and the windshield wipers when
the engine is off. This position will allow you to turn off
the engine.
C (ON/RUN):This position is for driving. It is the position
the ignition switch returns to after the engine starts, and
the control knob is released.
If you need to shift the transmission out of P (Park), the
ignition control knob has to be in ACC/ACCESSORY or
ON/RUN.
The battery could be drained if you leave the key in the
ACC/ACCESSORY or ON/RUN position with the engine
off. You may not be able to start your vehicle if the battery
is allowed to drain for an extended period of time.
D (START):This position starts the engine.
2-32

Automatic Transmission Operation
The shift lever is located on the center console between
the front seats.
There are several different
positions for the shift lever.
P (Park):This position locks the rear wheels. It is the
best position to use when you start the engine because
the vehicle cannot move easily.{CAUTION:
It is dangerous to get out of the vehicle if the shift
lever is not fully in P (Park) with the parking brake
rmly set. The vehicle can roll.
Do not leave the vehicle when the engine is running
unless you have to. If you have left the engine
running, the vehicle can move suddenly. You or
others could be injured. To be sure the vehicle will
not move, even when you are on fairly level ground,
always set the parking brake and move the shift
lever to P (Park). SeeShifting Into Park (Automatic
Transmission) on page 2-47. If you are pulling a
trailer, seeTowing a Trailer (CTS-V) on page 4-27
orTowing a Trailer (CTS) on page 4-28.
Make sure the shift lever is fully in P (Park) before starting
the engine. The vehicle has an automatic transmission
shift lock control system. You must fully apply the regular
brakes rst and then press the shift lever button before
you can shift from P (Park) when the ignition key is in
ON/RUN. If you cannot shift out of P (Park), ease
pressure on the shift lever and push the shift lever all the
way into P (Park) as you maintain brake application. Then
press the shift lever button and move the shift lever into
another gear. SeeShifting Out of Park on page 2-48.
2-36