Page 204 of 428

Audio System(s)
Determine which radio the vehicle has and read the
following pages to become familiar with its features.
{CAUTION:
Taking your eyes off the road for extended periods
could cause a crash resulting in injury or death to
you or others. Do not give extended attention to
entertainment tasks while driving.
This system provides access to many audio and non
audio listings.
To minimize taking your eyes off the road while driving,
do the following while the vehicle is parked:
Become familiar with the operation and controls of
the audio system.
Set up the tone, speaker adjustments, and preset
radio stations.
For more information, seeDefensive Driving on
page 4-2.Notice:Contact your dealer/retailer before adding
any equipment.
Adding audio or communication equipment could
interfere with the operation of the vehicle’s engine,
radio, or other systems, and could damage them.
Follow federal rules covering mobile radio and
telephone equipment.
Notice:The chime signals related to safety belts,
parking brake, and other functions of your vehicle
operate through the radio/entertainment system.
If that equipment is replaced or additional equipment
is added to your vehicle, the chimes may not
work. Make sure that replacement or additional
equipment is compatible with your vehicle before
installing it. SeeAccessories and Modifications
on page 5-3.
The vehicle has Retained Accessory Power (RAP).
With RAP, the audio system can be played even after
the ignition is turned off. SeeRetained Accessory
Power (RAP) on page 2-22for more information.Setting the Clock
Press and hold H until the correct hour and AM or PM
displays. Press and hold M until the correct minute
displays. The clock can be set with the ignition on or off.
3-82
Page 207 of 428

Finding a Station
BAND:Press to choose between FM1, FM2, AM, or
XM1orXM2.
e(Tune):Turn to select radio stations.
oSEEKp:Press and release to go to the previous or
the next station and stay there.
To scan stations, press and hold either arrow for more
than two seconds. SCAN or SCN displays and the radio
beeps once. The radio goes to a station, plays for a few
seconds, and then goes to the next station. Press either
arrow again or one of the pushbuttons to stop scanning
presets.
To scan preset stations, press and hold either arrow for
more than four seconds. PSCAN or PSC displays and the
radio beeps twice. The radio goes to a preset station,
plays for a few seconds, then goes to the next preset
station. Press either arrow again or one of the
pushbuttons to stop scanning presets.The radio seeks and scans stations only with a strong
signal that are in the selected band.
SCAN:On the radio with six-disc CD, press until
SC displays. The radio goes to a station, plays for
a few seconds, and then goes to the next station.
Press again to stop scanning stations.
The radio scans stations only with a strong signal that
are in the selected band.
INFO (Information) (XM Satellite Radio Service Only):
The vehicle’s radio may have an INFO button. If the
current station on the radio has a message, the
information symbol displays. Press to see the message.
If the entire message is not displayed, parts of the
message appears every three seconds. To manually
scroll through the message, press and release the
INFO button.
When a message is not available from a station,
NO INFO displays.
3-85
Page 208 of 428

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, six AM, six XM1
and six XM2) can be programmed on the six numbered
pushbuttons.
To program either radio:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, AM, or XM1™ or
XM2™ (if equipped).
3. Tune to the desired station.
4. Press EQ to select the equalization.
5. Press and hold one of the six numbered
pushbuttons until the radio beeps once. When
that numbered pushbutton is pressed again, the
station and equalization that were stored, returns.
6. Repeat the steps for each pushbutton.
Setting the Tone (Bass/Treble)
e
(Bass/Treble):Press and release until BASS or
TREBLE displays. Turn
eto increase or to decrease
the bass or treble.
Press and hold
eto adjust the bass and treble to the
middle position. The radio beeps once.
To adjust all tone and speaker controls to the middle
position, press and hold
ewhen no tone or speaker
control displays. ALL CENTERED displays and the
radio beeps once.
EQ (Equalization):Press to select customized
equalization settings.
To return the bass and treble to the manual mode,
press and release until BASS or TREBLE displays.
3-86
Page 212 of 428