2009 AUDI S4 CABRIOLET service

_________________________________________________ F_ u_ s_ e_s _ a_n _ d_ b_ u_lb _ s ____ lllll
•
& W ARNING (conti nued )
• If you are uncert ain about what to do , have the work performed
by an author ized Audi dealer or other qualified workshop. Serious
personal injury may result from improperly performed work .
[ i] Tips
• If you must replace the light bu lbs you rself, a lways remember
t hat t he engi ne c ompart ment of any ve hicle is a hazardous area to
work in. Always read and heed a ll WARNI NGS =>
page 242, "Engine
c o m pa rtment" =>& .
• It is best to ask your authorized Audi dea ler whenever you need
to cha nge a bulb .•
Do-it-yourself service

______________________________________________ E_ m_ e_r -=g :...e _ n_ c __a. y_ s_it _u_ a_ ti_o _ n_ s _ __,11111
& WARNING (continued)
• Before you check anything in the engine compartment, always
read and heed all WARNINGS~ page 242, "Engine compartment".
0 Note
• Applying a higher voltage booster battery will cause expensive
damage to sensitive electronic components, such as control units,
relays, radio, etc .
• There must be no electrical contact between the vehicles as
otherwise current could already start to flow as soon as the positive
(+) terminals are connected.
[ i] Tips
The discharged battery must be properly connected to the vehicle's
electrical system. •
Use of jumper cables
Make sure to connect the jumper cable clamps in exactly
the order described below!
Fig. 225 Jump·
starting with the
battery of another
vehicle : A -discharged
vehicle battery, B -
booster battery
Vehicle with discharged battery:
- Turn off lights and accessories, move lever of automatic
transmission to
N (Neutral) or P (Park) and set parking
brake.
Connect POSITIVE (+) to POSITIVE (+) (red)
1. Connect clamp of plus cable to positive(+) terminal G)
~ fig. 225 of discharged vehicle battery@.
2. Connect clamp on opposite end of cable to positive(+)
terminal
® of booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-) (black)
3. Connect clamp of minus cable (black) to negative( -)
terminal
0 of booster battery@.
4. Connect clamp on opposite end of negative cable to the
negative( -) terminal © of the discharged vehicle battery
@.
- Check that all screw plugs on the battery cells are
screwed in firmly. If not, tighten plugs prior to
connecting clamp on negative battery terminal.
Starting the engine
- Start the engine of the vehicle with the booster battery.
Run the engine at a moderate speed.
- Start engine with discharged vehicle battery in the usual
manner.
- If the engine fails to start: do not keep the starter
cranking for longer than 10 seconds. Wait for about 30
seconds and then try again. .,,.
~ehicle care Do-it-yourse lf service Technical data

111!1.___E_ m __ e_r -=g :...e_ n_ c-=y _ s_ i_t _u _a _t_ i_o _n_ s _______________________________________________ _
-With en gine run ning, r em ove jum per ca bles from both
v ehi cle s in exact
reve rs e o rd er.
T he battery is ve nted t o th e outs ide to preve nt gases from enter ing
the vehicle interior.
M ake s ure t hat th e jum per cla m ps are well co nnecte d with th eir
metal parts in full contact with the battery t erminals .
& WARNING
To avoid serious personal injury and damage to the vehicle , heed
all warnings and instructions of the jumper cable manufacturer. If
in doubt , call for road service .
• Jumper cables must be long enough so that the vehicles do not
touch .
• When connecting jumper cables , make sure that they cannot
get caught in any moving parts in the engine compartment .
• Before you check anything in the engine compartment, always
read and heed all WARNINGS=>
page 242, "Engine compartment ".
0 Note
Improper hook -up of jumper cables can ruin the generator.
• Always connec t POSIT IVE( +) to POS ITIVE ( +J, and NEG ATIV E (- J to
N EGAT IVE(-) te rminal.
• C heck that a ll screw plugs on the battery cel ls are screwed in
firm ly . I f not, tighten plugs prior to connec ting cla m p on nega tive
battery te rminal.
• P lease no te tha t th e procedure fo r con nec ting a ju mp er ca ble as
described above app lies specifical ly to t he case of your vehicle
b eing j ump st arted. When yo u are g iv in g a jum p start to another
veh ic le, do
not conn ect the minus(-) ca ble to the m inus( -) te rmina l
on the discha rge d battery ©=>
page 305, fig. 225. In stead , secu rely
co nnect the m inus(-) cable to e ither a m ass ive metal compone nt
that is firmly bo lted to the engine bloc k or to the engine b lock itse lf. I
f th e battery that is b ein g charged does not vent to the outside,
escapi ng battery ga s cou ld ignit e a nd ex plod e!•
Emergency towing with commercial
tow truck
General hints
Yo ur A udi requires s pecial handl in g f or t owing.
The fol lowing information i s to be used by commercial tow truck
operators who know how to operat e their equ ipment safe ly.
• Never tow your Audi, towing will cause damage to the engine
and transmission.
• Never wrap the safety chains or winch cables around the brake
lines.
• To prevent unnecessary damage , your Audi must be transported
with a car carrier (flat bed truck ).
• To load the vehicle on to the flat bed , use the towing loop found
in the vehicle tools and attach to the front or rear anchorage
=> page 3 07 and => page 307.
& WARNING
A vehicle being towed is not safe for passengers. Never allow
anyone to ride in a vehicle being towed , for any reason. •

________________________________________________ E_ m_ e_r ""g '-e_ n _ c..::y;..._ s_ i_t _u _a_ t_ i_o _n_ s _ __,_
Front towing loop
Do not install the front towing loop until it is needed.
Fig. 226 Front
bumper: removing the
cover cap
Fig . 227 Front
bumper: screwing in
the towing loop
The towing loop fits into the threaded hole located on the
right side of the front bumper and covered by a small cap
when not in use. -
Remove the towing loop from the vehicle tools
=> page 290.
-Press on the bottom edge of the cover cap to disengage
it from the bumper. The cap remains connected to the
bumper => fig. 226.
- Screw the towing loop into the threaded hole as far as it
will go
=> fig. 227, then tighten it with the wheel bolt
wrench.
When it is no longer needed , unscrew the towing loop and put it
back into the onboard toolkit. Make sure to have the towing loop
stored in the vehicle at all times .
& WARNING
If the towing loop is not screwed in as far as it will go, the thread
can pull out when the vehicle is towed -potential risk of an
accident. •
Rear towing loop
Fig. 228 Rear bumper,
right side: location of
rear towing loop
The rear towing eye is welded to the chassis under the rear bumper
on the right side.•
~ehicle care Do-it-yourse lf service Technical data

________________________________________________ E _m_ e_r.:g :;,. e_ n_c ...: y:.- s_ i_ t _u _a_ t_ i_ o _ n_ s ____ fflll
•
- In se rt a rubber pad betwee n th e floor jack/ wo rk sh op
h oi st and the li ftin g p oin ts .
If you must lift your vehicle with a floor jack to work underneath , be
sure the vehicle is safely supported on stands intended for this
purpose .
Fr ont lifting point
The lifting poi nt is located on the floo r pan rei nforceme nt about at
the same leve l as the jack mounting point~ page
308, fig. 230. Do
not lift the vehicle at the vertical sill reinforcement.
Rear lifting point
The li ftin g point is locate d on t he vert ical re inforceme nt of th e low er
sil l for the on board jack~ page
30 8, fig. 23 1.
Lifting with vehi cle ja ck
Refer to
~ page 296.
& WARNING
• To reduce the ri sk of serious injury and vehicle damage.
- Always l ift the vehicle only at the special workshop hoist and
floor jack lift points illustrated
~ page 308 , fig. 230 and
~ page 308, fig. 231.
- Failure to lift the vehicle at these points could cause the
vehicle to tilt or fall from a lift if there is a change in vehicle
weight distribution and balan ce . This might happen , for
e xample , when heavy components such as the engine block or
transmission are removed .
• When removing heavy components like these, anchor vehicle
to hoist or add correspond ing we ights to maintain the center of
gravity. Otherwise , the vehicle might tilt or slip off the hoist ,
causing ser ious personal injury .
0 Note
• Be aware of the fo llowing po ints be fore l ifting the ve hicle:
- The vehicle should never be lifted o r ja cked up from under ­
neath the engine oil pan , the tran smis sion housing , the front or
rear a xle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame , a rubber
pad must be inserted between the floor jack and the lift points .
- Before dr iving over a workshop hoist , check that the vehicle
weight does not exceed the permis sible lifting capacity of the
hoist .
- Before driving over a workshop hoist , en sure that there i s
sufficient clearance between the hoist and low parts of the
vehicle. •
Do-it-yourself service

General information -________________ ,,..
vehicle identification number of your vehicle (perforation) as well as
t he Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight
Rating (GAWR).
Th e high voltage warning label
is located on the lock carrier .
The s pa rk ign iti on syst em compl ies with th e Canadi an
s tandard ICES-002 . •
Weights
G ross V ehicl e W eight R atin g
The Gross Vehic le Weight Rating (GVWR), and the Gross Axle Weigh t
Rating (GAWR) for front and rear are listed on a sticker on the left
door ja mb.
The Gross Vehicle Weight Rating includes the weight of the basic
vehicle pl us fu ll f uel tank, oil and coolant, plus maximum load,
wh ic h inc ludes passenger weight (150 lbs/68 kg per designated
seating position) and luggage weight.
Gross Axle We ight Rating
The Gross Axle Weight Rating is the maximum load that can be
app lied at each axle of the vehicle~ &.
Vehicle capacity weight
The vehicle capacity weigh t (max. load) is listed ei ther on the
driver's side B -p illar or inside the fuel filler flap .
& WARNING
• The actual Gro ss Axle Weight Rating at the front and rear axles
s h ould not e xceed the permi ssible weight s, and their comb in ation
mu st not exceed the Gro ss Vehicle Wei ght Rating.
Controls . and equip­
ment . Safety first Vehicle operation
& W
ARNING (conti nued )
• Exceeding pe rmi ssible weight ratings can result in vehicle
d am age , ac ciden ts a nd per sonal inj ury .
0 Note
• The vehicle capacity weight figures apply when the load is
distributed even ly in the vehicle (passengers and luggage) . When
transporting a heavy load in the luggage compartment, carry the
load as near to the rear axle as possib le so that the vehicle 's
handl ing is not impai red.
• Do not exceed the maximum permiss ib le axle loads or the
maximum gross vehicle weight . Always remember tha t the veh ic le's
handling wil l be affected by the extra load. Therefore, adjust your
speed according ly .
• Always observe local regulations. •
Dimensions
The specifications refer to the basic model. Differences may occur
depending on the mode l type and op tions o rdered, for example, tire
sizes.
0 Note
When driving up steep ramps, on rough roads, over curbs , etc . it is
important to remember that some parts of your vehic le, such as
spoilers or exhaust system components, may be close to the
g round. Be ca reful not to damage them. •
Vehicle care Do-it-yourself service Tec hn ica l da ta

Data -----------------
Applies t o vehicl es: wi th 3.2 liter 6-c yl. engine
255 hp , 3.2 liter 6-cyl. engine
Engine data
Maximum output SAE net
Maximum torque SAE net
N o. of cy linders
Displacement
Stroke
Bore
Compression ratio
F uel
Dimensions (appro x.)
L e ngth (with licence plate bracke t)
Width (across m irrors)
Height (unloaded)
Turning circle diameter (curb to curb )
Capacities (appr ox .>
Fuel tank
- To tal capacity
- Reserve (of total capacity)
Windshield and he adlight wa sher fluid container
Engine oil
with filter change hp@rpm
lb
-ft@ rpm
C ID (cm
3
)
in (mm)
in (mm)
255@ 6500
243@3250
6
190 (3123)
3 .65 (92 .8)
3 .33 (8 4.5)
10.1 : 1
Premium unleaded 191 AKI)
Re commended for maximum engine performance . Fur­
ther details =>
page 244, "Gasoline"
in ( mm)
in (mm)
in (mm)
ft. (ml
1 80 ( 4573)
76 .2 (1937)
54 .8 (139 1)
36.4 (11 .1)
gal/l itres
gal/litres
quarts /litres
qua rts/l itres 16.6 / 63.0
2 .1 / 8.0
5 .1 / 4.8
6.9 / 6 .5
•
Controls . and equip­
ment . Safety first Vehicle operation
Vehicle care Do-it-yourself service Tec hn ica l da ta

___ C_ o_n_ s_ u_m _ e_ r_ ln_ f_ o _r _m _ a_ t_ i_o _n ______________________________________________ _
Consumer Information
Warranty coverages
Your Aud i is c overed b y the follo wing warra nti es:
• New Vehicle Limited Warranty
• Limited Warranty Against Corrosion Perforation
• Emissions Control System Warranty
• Emissions Performance Warranty
• California Emissions Control Warranty (USA vehicles only)
• California Emissions Performance Warranty (USA vehicles only)
Detailed information regarding your warranties can be found in
your
Warr anty & M aint ena nce booklet .•
Operating your vehicle outside the
U .S.A. or Canada
Government regulations in the United States and Canada require
that auto mobiles meet specific em ission regulations and safety
standards . Therefore, vehic les built for the U .S .A. and Canada differ
from veh icles sold in other countries .
If you plan to take your vehic le outside the continental limits of the
United States or Canada, there is the possibility that
• unleaded fue ls for vehicles with cata lyt ic converter may not be
available;
• f uel may have a considerably lower octane rat ing . Imprope r fuel
may cause engine damage;
• service may be inadequate due to lack of proper service facilities,
tools or testing equipment;
• replacement parts may not be readily avai lable . •
Navigation systems for vehicles built for the U.S.A . and Canada
wil l not necessarily work in Europe, and may not work in other coun ­
tries outside of North America.
0 Note
Audi cann ot be responsible for mechanica l damage that could
resu lt from inadequate fuel, service or parts avai lability .•
Audi Service Repair Manuals and
Literature
Audi Official Factory Service Manuals are published as soon as
possible after model introduction . Se rvice manua ls are availab le
from :
Audi Technical Literature Ordering Center
Call tol l-free:
Tel. :
1 (800) 544-802 1
(from 8:00 AM to 8 :00 P M, EST, Monday through Friday)
or access thei r website
www .audi .dd sltd .com on the Internet to
order repair manua ls and other Audi literature. •
Maintenance
General
Your vehicle has been designe d to he lp keep maintenance requ ire ­
ments to a minimum. However, a certain amount of regu lar mainte ­
n ance is sti ll necessary to assu re your vehic le's safety, economy and ..,,