2009 AUDI Q7 warning

_____________________________________________ W.:..:..; h:..:.= a:.:t ..:.d=-= o:....:... I .::d :.:o :....:.. n:.:o::.. w.:...:.. ?:...___J -
& WARNING !continued)
• If you must work under the vehicle, always use safety stands
specifically designed for this purpose.
• Always make sure the inflatable spare tire and even a flat tire
are secured in place and not loose, otherwise they could fly
forward, causing personal injury to passengers in the vehicle in an
accident or sudden maneuver . •
Tools
The tool kit is located in the luggage compartment under
the cargo floor cover.
The onboard tool kit includes:
• Hook for removing wheel covers *
• Plastic hook to remove wheel bolt covers
• Wheel bolt wr ench
• Alignment p in for changing wheels
• Screwdriver with reversible blade
• 10
x 13 open ended wrench
• Towing eye
Fig . 298 Luggage
compartment : vehicle
tool kit
[ i] Tips
Some of the on board items listed above are provided on certain
models only or are optional extras .•
A pp lies to ve hicles: w ith bass box
R emoving bass box
Before the inflatable spare tire can be taken out, the bass
box must be removed.
Fig . 299 Spare wheel
well : Bass box
Removing bass box
- Squeeze the locking tabs~ fig. 299 G) of the connector.
- Disconnect the connector @ and place the lead to one
side.
- Turn the large screw counter-clockwise.
- Carefully remove the bass box.
Installing bass box
-Carefully place the bass box in the wheel. The inscription
" FRONT " on the bass box must face forward.
- Reconnect the connector that was removed.
Vehicle care Do-it-yourself service irechnical data

-What do I do novv? PV:f.,___ ______________ _
-Secu re th e bass b ox w it h t he larg e sc re w. •
Inflatable spare t ire
T he i nfla tab le sp are tir e ex pand s to its full di amet er wh en
it is inflated.
Removing inflatable spare tire
Fig . 300 Inflat able
spare t ire with
compres sor
Li ft up th e carg o floo r u sing the handl e.
- T urn t he l arg e scre w:::> fig. 300 coun ter-c loc kwi se.
Re move the bass bo x as req uir e d :::>
page 371.
- Take o ut th e inflatable s pare t ire.
Stowing the inflatable spare tire
Relea se th e air by un screwing the valve st em .
Sc re w the va lv e st em b ack in afte rwards.
Wait a few hours b efo re pl acin g the wh eel in th e sp are
w he el w ell :::>
& .
Install t he bass b ox as require d:::> page 371.
S ec ure the whe el wit h th e large s cre w. - Fo
ld the cargo floor bac k d own.
After using the inflatable spare wheel
The inflatab le spare ti re can be re-used as long as it is not damaged
an d is n ot worn d own to the tre ad wea r indi cato rs=> &.
When you l et the air out of the inflatabl e spare tir e, it do es not
a ss ume it s fo lded shape aga in for severa l hou rs . U ntil then, it
c annot be plac ed bac k in the sp are whe el well and s tow ed sec urel y.
& WARNING
• Never use the spare tire if it is damaged or if it is worn down to
the tread wear indicators.
• If the inflatable spare tire is more than 6 years old, use it only
in an emergency and with extreme caution and careful driving.
• The inflatable spare tire is intended only for temporary and
short-term use. It should be replaced as soon as possible with the
normal wheel and tire .
• Maximum inflation pressure for the inflatable spare tire is
50 PSI (3 .5 bar).
• Maximum permissible speed is 50 mph (80 km /h ).
• Avoid full -throttle acceleration , heavy braking, and fast
cornering .
• When the air is let out of the inflatable spare wheel , it does not
assume its folded shape for several hours . Until then , it cannot be
placed back in the spare wheel well and stowed securely .
• Never drive with more than one inflatable spare tire.
• For technical reasons , the use of tire chains on the inflatable
spare tire is not permitted . If it is necessary to drive with tire
chains, the inflatable spare wheel must be mounted on the front
axle in the event of a flat in a rear tire. The newly available front
wheel must then be installed in place of the rear wheel with the
flat tire . Installing the tire chain before mounting the wheel and
tire is recommended . .,.

What do I do now? -
---------------~.;______
•
& WARNING (continued)
• Loose items in the passenger compartment can cause serious
personal injury during hard braking or in an accident .
- Never store the inflatable spare tire or jack and tools in the
passenger compartment.
- Always store all jacking equipment, tools, and the inflatable
spare tire in the luggage compartment.
- Tighten the knurled retaining screw for the inflatable spare
tire securely.
0 Note
• Th e inflatable spare tire has been developed specifically for this
vehicle model. It must not be exchanged or used for other vehicle
models. Similarly, inflatable tires from other vehicle models must
not be used.
• Normal summer or winter tires must not be installed on the
inflatable tire rim.•
Changing a wheel
Before changing a wheel
Observe the following precautions for your own and your
passenger's safety when changing a wheel.
-After you experience a tire failure, pull the car well away
from moving traffic and try to reach
level ground before
you stop => & .
- All passengers should
leave the car and move to a safe
location (for instance, behind the guardrail)=> &.
- Engage the
parking brake to prevent your vehicle from
rolling unintentionally=> &. -
Move
selector lever to position P =:> & .
- If you are towing a trailer: unhitch the trailer from your
vehicle.
- Block the diagonally opposite wheel with the folding
chocks or other objects.
- Take the
jack and the inflatable spare tire out of the
luggage compartment=>
page 370.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flashers on and use other warning
devices to alert other motorists.
• Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack , always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed with the
folding chocks or other objects. When one front wheel is lifted off
the ground, placing the Automatic Transmission in "P" (Park) will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and firm .
If necessary, use a sturdy board under the jack.
• After installing the inflatable spare tire, make sure that you
replace the flat tire/wheel in its storage area properly and tighten
the knurled retaining screw securely. •
Do-it -yourself service

lll'Jl,___W_ h_ a_ t_ d_o_ l_ d_ o _ n_ o_w _ ? ____________________________________________ _
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order.
1. Activate the vehicle jack mode (only vehicles with Adap­
tive Air Suspension) ~
page 210.
2. Remove the decorative wheel cover*. For more details
see also~
page 375, "Decorative wheel covers" or
~ page 375, "Wheels with wheel bolt caps".
3. Loosen the wheel bolts ~ page 376.
4. Locate the proper mounting point for the jack and align
the jack below that point~
page 376.
5. Lift the car with the jack~ page 376.
6. Remove the wheel with the flat tire and then install the
inflatable spare tire =>
page 378.
7. Tighten all wheel bolts lightly.
8.
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten all wheel
bolts
~ page 376.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode (only vehicles with
Adaptive Air Suspension)=>
page 210.
& WARNING
Always read and follow all WARNINGS and information => & in
"Raising the vehicle" on
page 376 and => page 379. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wheel you replaced in the spare
wheel well.
- Replace the tools and the jack in their proper location.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 120 ft lb (160 Nm).
- Have t he flat tire
replaced as soon as possible.
[ i] Tips
• I f you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced before you check
the tightening torque .
• Drive at reduced speed until you have the tightening torques
checked .•

lllftl.,___W_ h_ a _ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising the
vehicle.
Loosening
Fig . 303 Changing a
wheel: loosening the
wheel bolts
- Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
- Take tight hold of the
end of the wrench handle and turn
the wheel bolts counter-clockwise about
one single turn
in the direction of arrow::::, fig. 303.
Tightening
- Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
- Take tight hold of the
end of the wrench handle and turn
each wheel bolt clockwise until it is seated.
& WARNING
• Do not use force or hurry when changing a wheel -you can
cause the vehicle to slip off the jack and cause serious personal
injuries.
& WARNING (continued)
• Do not loosen the wheel bolts more than one turn before you
raise the vehicle with the jack. -You risk an injury.
[ i] Tips
If a wheel bolt is very tight, you may find it easier to loosen by care­
fully pushing down on the end of the wheel bolt wrench with
one
foot only.
As you do so, hold on to the car to keep your balance and
take care not to slip. •
Raising the vehicle
The vehicle must be lifted with the jack first before the
wheel can be removed.
Fig. 304 Changing a
wheel: mounting
points for the jack ..

_____________________________________________ W_ h_ a_t _d_ o_l _ d_o _ n_o_ w_ ? _ __._
Fig. 30 5 Close- up:
prope r po sit io ning of
jack
- Posi tion the jack b elow the doo r sill u nder t he mounting
point
t ha t is clos est to the w hee l to be cha nged
==> p age 376, fi g. 30 4.
- Wind the jack up un der the liftin g p oint un til the c law is
d ir ect ly un der t he ver tical rib on th e ro cke r pane l==:> & .
- Align t he jack so the claw@ grip s the rib on th e rocke r
pane l and th e fl exible base plate @ is flat o n the gr oun d
==> page 3 77, fig. 30 5.
- Wind t he jack up furt her u ntil the flat ti re come s off the
g roun d==:> & .
The jack must be instal led only at the places indicated=> pa ge 376,
fi g. 30 4. T here is e xactl y on e loca tion for each w heel. The jack must
not be positioned at any oth er location =:>& .
A n
unstable surface under the jack can cause the vehic le to s lip off
the ja c k. Al ways pro vid e a firm base for the jack on t he grou nd. If
necessary place a sturd y board or s imilar sup port under the jack. On
hard , slippery surface s {such as tile s) us e a rub ber mat or s imi lar to
p revent the jack from slipping =:>& .
& WARNING
• You or your passengers could be injured wh ile changing a
wheel if you do not follow these safety precautions:
-Positioning the jack under the vehicle at any othe r place than
those indicated above may damage the vehicle or may result in personal injuries.
- A soft or unstable surface under the jack may cause the
vehicle to slip off the jack . Always provide a firm base for the
jack on the ground. If necessary, use a sturdy board under the
jack.
- On hard, slippery surface (such as tiles ) use a rubber mat or
similar to prevent the jack from slipping .
• To help prevent injury to yourself and your passengers:
-Do not raise the vehicle until you are sure the jack is securely
engaged.
- Passengers must not remain in the vehicle when it is jacked
up.
- Make sure that passengers wait
in a safe place away from
the vehicle and well away from the road and traffic.
- Make sure jack position is correct, adjust as necessary and
then continue to rai se the jack.
[ i ] Tips
B efore c hang in g the whee l, you must activate the jac king mode, so
that the au tomatic con trols for the Adaptive Air Suspension * do not
m ak e it mo re diff icu lt to lif t the v ehic le wi th t he jack =:>
page 210. •
Vehicle care Do-it-yourself service irechnical data

_______________________________________________ W_ h_ a_t _ d_ o_ l _d _o_ n_ o _ w_ ? __ IIIII
•
- Let the compressor run until it has reached 50 PSI (3.5
bar). Switch the compressor off after running for 8
minutes at the most -danger of overheating!
& WARNING
The compressor and the tire filler hose can become extremely hot
while they are running -danger of burns!
0 Note
Switch the compressor off after running for 8 minutes at the most -
danger of overheating! Allow the compressor to cool down for a few
minutes before you use it again.
[ i] Tips
The compressor must not be connected to the cigarette lighter
socket, as this socket does not provide the required power .•
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern intended for use
in a specific direction
When using a spare tire with a tread pattern intended for use in a
specific direction, please note the following:
• The direction of rotation is marked by an arrow on the side of the
tire.
• If the spare tire has to be installed in the incorrect direction, use
the spare tire only temporarily since the tire will not be able to
achieve its optimum performance characteristics with regard to
aquaplaning, noise and wear. •
We recommend that you pay particular attention to this fact
during wet weather and that you adjust your speed to match road
conditions.
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible to restore the handling advantages of a
unidirectional tire. •
Notes on wheel changing
Please read the information => page 359, "New tires and replacing
tires and wheels " if you are going to use a spare tire which is
different from the tires on your vehicle.
After you change a tire :
• Check the tire pressure on the spare immediately after installa­
tion.
• Have the wheel bolt tightening torque checked with a torque
wrench as soon as possible by your authorized Audi dealer or a
qualified workshop.
• With steel and alloy wheel rims, the wheel bolts are correctly
tightened at a torque of 120 ft lb (160 Nm).
• If you notice that the wheel bolts are corroded and difficult to
turn while changing a tire, they should be replaced before you check
the tightening torque.
• Replace the flat tire with a new one and have it installed on your
vehicle as soon as possible. Remount the wheel cover.
Until then, drive with extra care and at reduced speeds .
& WARNING
• If you are going to equip your vehicle with tires or rims which
differ from those which were factory installed, then be sure to read
the information
=> page 359, "New tires and replacing tires and
wheels". ..
Do-it -yourself service

_________________________________________________ F_ u_ s_ e_s _ a_n _d_ b_ u _ lb_ s _ __._
Fuses and bulbs
Fuses
Replacing a fuse
A problem in the electrical system may be caused by a
blown fuse.
Fig . 307 Ins trument
pa nel left: Face c over
F ig . 308 I nst rume nt
pa nel left: Co ntent
F ac e cover
- Locate the fuse which belongs to the component which
failed.
- Switch off the ignition and the e lectr ica l component
affected. - Carefully p
ry t he face cover off the instr umen t pane l
using the ignition key or a screwdriver~ fig. 307.
- Rem ove the plastic clip @ from i ts retainer in the face
cove r~ fig. 308, p lace i t over the questionable fuse and
remove the fuse.
- Replace a blown fuse (recognizable by the melted metal
str ip inside) wi th a f use of the
same amperage.
The individual circuits are protected by fuses. T he fuse panels with
the fuses are located on the left and right front faces of the instru­
ment pane l behind a cover and in the right storage area in the
luggage compartment.
There is a plastic clip @ in the cover on the lef t side of the instru ­
ment pane l, which can be used to remove the fuses . The crank © is
used for emergency operation of the Panoramic sliding sun roof *.
You w ill also find a label on both covers in the instrument panel with
the fuse layout © for the corresponding fuse panel.
& WARNING
Nev er replac e a fuse with one that ha s a high er amperag e rati ng.
• A fu se w ith a to o high ampe rage could damage the ele ctr ical
pa rt a nd cause a fire .
0 Note
• On no account should fuses be repaired (e .g. patched up wi th tin
foil or wire) as this may cause serious damage elsewhere in the e lec­
trica l circuit o r cause fire.
• If a fuse blows repeatedly, do not keep replacing it. Instead , have
the cause of the repea ted short circuit or overload located and fixed.
ti>
Vehicle care Do-it-yourself service Technical data