2009 Acura TSX lock

Remove the light assembly cover
by pulling its outside edge.
Open the trunk.Test the new bulb to make sure it
works.
Push a new bulb straight into the
socket until it bottoms, and
reinstall the socket into the light
assembly by turning it clockwise
until it locks.
Reinstall the light assembly cover.
Determine which of the three
bulbs is burned out: stop/taillight,
rear side-marker, or turn signal
light.
Remove the socket by turning it
one-quarter turn counterclockwise,
and pull the bulb straight out of its
socket. 5.
6.
3.
4.
1.
2. 7.
Lights
Replacing Rear Bulbs
(In Fenders)
436
COVER
\f—\f—\fy
\f
y
)!
\f\fy\f
y
2009 TSX

CONT INUED
Open the trunk.
Toreplaceabulboneitherside,
remove the two f asteners on the
left side, or a fastener on the right
side.Pull back the appropriate corner of
the trunk lid lining caref ully.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
3. 4.
5.
1.
2.
Lights
Replacing a Back-up L ight Bulb
(in T runk L id)
Maint enance
437
FASTENERS SOCKET
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Reinstall the trunk lid lining. Make
sure it is installed under the edge
of the trunk seal.
Install the f asteners.Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
6.
7.
8.
9.
Lights
Side T urn Signal L ights
Rear License Plate Light Bulbs
438
\f—\f—\fy

y
)!
\f\fy\fy
2009 TSX

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Open the trunk, and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.Reinstall the socket. Turn it
clockwise until it locks. Make sure
the new bulb is working.
2.
1. 3.
Lights
Replacing the High-mount Brake
Light
Maint enance
439
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Install the new bulb into the hole
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the holding clips, and
push in its head of each clip.
3.
4. 5.
6.
7.
8.
Lights
Maint enance
441
\f—\f—\fy
y
)!
\f\fy\fy
2009 TSX

If your seat belts get dirty, use a sof t
brush with a mixture of mild soap
and warm water to clean them. Do
not use bleach, dye, or cleaning
solvents. Let the belts air dry bef ore
you use the vehicle.Dirt build-up around the openings of
the seat belt anchors can cause the
belts to retract slowly. Wipe the
openings with a clean cloth
dampened in mild soap and warm
water or isopropyl alcohol.
The driver’s f loor mat that came
with your vehicle hooks over the
f loor mat anchors. To lock each
hook, turn the knob clockwise. This
keeps the f loor mat f rom sliding
f orward and possibly interf ering with
the pedals.
When cleaning or replacing, turn the
knob counterclockwise to unhook
the floor mat.
Floor Mats
Cleaning the Seat Belts
Cleaning the Seat Belts, Floor Mats
442
Driver’s floor mat is shown.
OPENING
To unlock
\f—\f—\fy
\fy
)!
\f\fy\fy
2009 TSX

To replace a wiper blade: Disconnect the blade assemblyfrom the wiper arm:
Raise each wiper arm of f the
windshield, lif ting the driver’s side
first, then the passenger’s side.
Check the condition of the wiper
blades at least every six months.
Replace them if you f ind signs of
cracking in the rubber, areas that are
getting hard, or if they leave streaks
and unwiped areas when used.
Put a cloth on the edge of the
lock tab, then push up on the
lock tab carefully with a flat-tip
screwdriver.
2.
1.
Wiper Blades
444
WIPER BLADES
LOCK TAB
Do not open the hood when the wiper
arms are raised, or you will damage the
hood and wiper arms.
\f—\f—\fy
\fy
)!
\f\fy\fy
2009 TSX

Place the top of the wiper blade on
the end of the blade assembly, and
slide the blade onto the assembly
in the direction pointed to by the
arrow.Slide the wiper blade assembly
onto the wiper arm. Push down
thelocktab.Makesurethewiper
blade assembly locks in place.
Lower the wiper arm down against
the windshield, the passenger’s
side first, then the driver’s side.
Make sure the tab on the blade
assembly fits in the indent of the
wiper blade and the blade is
completely installed.
5. 6.
7.
Wiper Blades
446
INDENT
TAB
\f—\f—\fy
y
)!
\f\fy\f
y
2009 TSX