2009.5 Peugeot 308 SW BL Dag remove seats
[x] Cancel search: remove seatsPage 49 of 313
!
67
COMFORT
REAR SEATS
Never drive with the head restraints
removed; they must be in place
and in the high position when pas-
sengers are seated in the rear.
R e a r h e a d r e s t r a i n t s
These have a high position (comfort
and safety) and a low position (rear visi-
bility).
They can also be removed.
To remove a head restraint:
pull the head restraint fully forwards
and upwards at the same time,
then, press the lug A . R e m o v i n g t h e s e a t c u s h i o n
Move the corresponding front seat
forwards if necessary.
Raise the seat cushion 1 lifting it
with a hand from the rear.
Tilt the seat cushion 1 fully against
the front seat.
Remove the seat cushion 1 from its
fi x i n g s b y p u l l i n g u p w a r d s .
R e f i t t i n g t h e s e a t c u s h i o n
Position the seat cushion 1 vertically in
i t s fi x i n g s .
Fold down the seat cushion 1 .
Press on the seat cushion to secure it.
Bench seat, the left-hand (2/3) or right-
hand (1/3) section of which can be folded
to adapt the boot load space.
Page 51 of 313
ii
i
69
COMFORT
REAR SEATS
F o r w a r d s - b a c k w a r d s a d j u s t m e n t
S e a t b a c k a n g l e a d j u s t m e n t
Pull one of the straps B , located
at the front of the seat, then adjust
the angle to one of the 7 positions
offered.
Release the strap to lock the seat
back in this position. Table position
Raise the bar A and slide the seat
forwards or backwards.
Place the head restraint in the low
position.
Pull one of the straps B , located at
the front of the seat.
Fold the seat back fully onto the
seat cushion; the seat automatically
moves back fully.
Press on the seat back to lock it. Folding
Once the seat has been placed in the
table position, carry out the following
operations:
move back the seat fully using the
bar A ,
raise the lever C , located at the rear
right of the seat, to release the rear
feet,
raise the seat fully so that it remains
in the fully folded position.
You can also carry out these oper-
ations from the 3rd row using one
of the straps B , located at the rear
of the seat. These operations allow access to
the 3
rd row, exit from the 3 rd row
and folding of the seats from the
boot.
In the 2nd row, these three seats are
identical and can be adjusted for your
comfort. They can be placed in the table
position, folded or removed to obtain a
v a r i e t y o f l o a d i n g c o n fi g u r a t i o n s .
During the forwards-backwards and
seat back angle adjustment opera-
tions, take care not to apply any force
to the load space cover roller.
Page 53 of 313
!
71
COMFORT
ADDITIONAL SEATS
Table position
Place the head restraint in the low
position.
Pull the strap A , located at the rear
left of the seat.
Fold the seat back onto the seat
cushion. Folding
Once the seat has been placed in the
table position, carry out the following
operations:
remove the load space cover roller,
raise the bar B , located at the rear of
the seat, to release the rear feet,
raise the seat and secure it to the
head restraint rod of the 2nd row
seat, using the integrated retaining
strap C . R e m o v a l
Once the seat has been folded, carry
out the following operations:
pull the red strap D to release the
front feet of the seat,
lift the seat and carry it using the
carrying handle E ,
put the anchorage covers back in
p l a c e t o o b t a i n a fl a t b o o t fl o o r .
Never use the adjustment and re-
taining straps to remove, install
or carry a seat; use the carrying
handle E provided for this purpose
(weight of the seat: approximately
15 kg).
In the 3rd row, these two seats are iden-
tical and are used for the occasional
carrying of additional passengers. They
can be placed in the table position,
folded or removed to obtain a variety of
l o a d i n g c o n fi g u r a t i o n s .
Page 55 of 313
i
!
73
COMFORT
SEAT MODULARITY AND VARIOUS CONFIGURATIONS
Examples of configurations 7 seats
Operations to change the existing
c o n fi g u r a t i o n m u s t o n l y b e c a r r i e d
o u t w h e n s t a t i o n a r y ( s e e t h e " R e a r
s e a t s " a n d " A d d i t i o n a l s e a t s " s e c -
tions of the SW with panoramic
sunroof).
Special features
The outer seats of the 2nd row can be
moved inwards, once the central seat
has been removed.
The 2nd row seats can be installed in
the 3rd row.
Conversely, the 3rd row seats cannot
be installed in the 2nd row.
5 s e a t s w i t h a d d i t i o n a l s e a t s f o l d e d
Do not seat passengers in the 3rd
row if the 2nd row seats are in the
fully folded position.
Designed to be modular, your vehicle
offers numerous seat installation and
l o a d i n g c o n fi g u r a t i o n s .
Page 104 of 313
i
110
FITTINGS
To remove the shelf:
unhook the two cords,
raise the shelf slightly, then remove it.
Rear parcel shelf
When changing a wheel
A n a d d i t i o n a l h o o k , u n d e r t h e s h e l f ,
permits easy access to the spare
wheel by retaining the boot carpet
by means of its cord.
The hooks permit the securing of shop-
ping bags.
Hooks
There are several options for storing the
shelf:
- either upright behind the front seats,
- o r fl a t a t t h e b a s e o f t h e b o o t .
Raise the boot carpet to gain access
t o t h e s t o r a g e b o x .
T h i s h a s a r e a s f o r s t o r i n g a b o x o f s p a r e
b u l b s , a fi r s t a i d k i t , a t e m p o r a r y t y r e r e -
pair kit, two warning triangles...
Storage box
Page 107 of 313
i
i
113
FITTINGS
High load retaining net
Hooked onto the special upper and low-
e r fi x i n g s , t h i s p e r m i t s u s e o f t h e e n t i r e
loading volume up to the roof:
- behind the rear seats (row 2),
- behind the front seats (row 1) when the rear seats are folded.
To use it in row 1:
o p e n t h e c o v e r s o f t h e u p p e r fi x i n g s 1 ,
unroll the high load retaining net,
position one of the ends of the net's
metal bar in the corresponding upper
fi x i n g 1 , then do the same with the
other end,
slacken the straps fully,
fi x t h e s n a p h o o k o f e a c h o f t h e
straps on the corresponding bar 3 ,
located under the cushion of the
rear seats,
fold the rear seats,
tighten the straps,
check that the net is hooked and
tightened correctly. To use it in row 2:
fold or remove the load space cover,
o p e n t h e c o v e r s o f t h e u p p e r fi x i n g s 2 ,
unroll the high load retaining net,
position one of the ends of the net's
metal bar in the corresponding upper
fi x i n g 2 , then do the same with the
other end,
fi x t h e s n a p h o o k o f e a c h o f t h e
straps in the corresponding ring 4 ,
located on the rear seats mechanism
support,
tighten the straps,
check that the net is hooked and
tightened correctly.
When positioning the net, check
that the strap loops are visible from
t h e b o o t ; t h i s w i l l m a k e s l a c k e n i n g
or tightening easier.
This net can be stored in the storage
t r a y o n t h e fl o o r .
Page 110 of 313
i
116
FITTINGS
High load retaining net
Hooked onto the special upper and lower
fi x i n g s , t h i s p e r m i t s u s e o f t h e e n t i r e l o a d -
ing volume up to the roof behind the seats
of the 2nd row. 12 V accessories socket
In order to connect a 12 V accessory
( m a x p o w e r : 1 2 0 W a t t s ) , r e m o v e
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
To use the net in the 2nd row (additional
seats folded or removed):
roll up or remove the load space
screen,
o p e n t h e c o v e r s o f t h e u p p e r fi x i n g s 1 ,
unroll the high load retaining net,
position one of the ends of the net's
metal bar in the corresponding upper
fi x i n g 1 , then do the same with the
other end,
attach the snap hook of each of the
net's straps in the corresponding
ring 2 , l o c a t e d o n t h e l o w e r fi x i n g o f
the rear side seat belt,
tighten the straps,
check that the net is hooked and
tightened correctly. Hooks
The hooks permit the securing of shop-
ping bags.
When positioning the net, check
that the strap loops are visible from
t h e b o o t ; t h i s w i l l m a k e s l a c k e n i n g
or tightening easier.
Page 115 of 313
120
CHILD SAFETY
LOCATION OF CHILD SEATS SECURED USING THE SEAT BELT
In accordance with European regulations, this table indicates the options for installing child seats secured using
the seat belt and universally approved (a) in relation to the weight of the child and the seat in the vehicle.
(a) Universal child seat: child seat which can be installed in all vehicles using the seat belt.
(b) Group 0: from birth to 10 kg. Infant car seats and "car cots" ca nnot be installed on the front passenger seat.
( c ) C o n s u l t t h e l e g i s l a t i o n i n f o r c e i n y o u r c o u n t r y b e f o r e i n s t a l l i n g y o u r c h i l d o n t h i s s e a t .
U : seat suitable for the installation of a child seat secu red using the seat belt and universally approved "rear facing" an d/or
"forward facing".
U(R1) : identical to U , with the vehicle's seat adjusted to the intermediate lo ngitudinal position.
U(R2) : identical to U , with the vehicle's seat adjusted to the highest positio n and moved back fully.
* The seat's head restraint must be removed and stored.
Seat
Weight of the child/ indicative age
Less than 13 kg
(groups 0 (b) and 0+)
U p t o ≈ 1 y e a r
From 9 to 18 kg
(group 1)
F r o m 1 t o ≈ 3 y e a r s
From 15 to 25 kg
(group 2)
F r o m 3 t o ≈ 6 y e a r s
From 22 to 36 kg
( g r o u p 3 )
F r o m 6 t o ≈ 1 0 y e a r s
Front passenger seat (c)
- fi x e d
U(R1) U(R1) U(R1) U(R1)
- height adjustable U(R2) U(R2) U(R2) U(R2)
R e a r o u t e r s e a t s
U U * U * U *
R e a r c e n t r e s e a t
U U * U * U *