2009.5 Citroen DS3 display

Monitoring
On switching on, the dial needles go to the extent of their travel then return to 0. A. With the ignition on, the fuel gauge bars for the fuel remaining should light up. B. With the engine running, the associated low level warning lamp should switch off. C. With the ignition on, the oil level indicator should display "OIL OK" for a few seconds. If the levels are not correct, top up the level
which is low.
Instrument panel
24
1. With the ignition on, the orange and red warning lamps come on. 2. With the engine running, these warning lamps should switch off. If a warning lamp remains on, refer to the page concerned.
Warning lamps
26
Lighting of the indicator lamp indicates the state of the corresponding system. A. Deactivation of interior volumtric protection.
Switch panel
87
B. Deactivation of the ESP/ASR system.
135

Driving safely
1. Selecting/Switching off speed limiter mode. 2. Decrease the programmed value. 3. Increase the programmed value. 4. Speed limiter on/off. The values must be set with the engine running.
Speed limiter "LIMIT"
155
1. Selecting/Switching off cruise control mode. 2. Decrease the programmed value. 3. Increase the programmed value. 4. Cruise control Off/Resume. In order to be programmed or activated, the vehicle speed must be higher than 25 mph (40 km/h), with at least four th gear engaged on a manual gearbox (second gear on an automatic gearbox).
Cruise control "CRUISE"
157
The cruise control or speed limiter mode appears on the instrument panel when it is selected.
Display in the instrument panel
Cruise control
Speed limiter

Petrol - Diesel instrument panels, manual or automatic gearbox
Provided with permanent back-lighting, the instrument panel groups together the vehicle's dials and indic ator and warning lamps.
1. Rev counter. Indicates the speed of rotation of the engine (x 1 000 rpm).
2. Vehicle speed. Indicates the current speed of the moving vehicle (mph or km/h). 3. Engine coolant temperature. Indicates the temperature of the engine coolant liquid (° Celsius).
Dials
7. Lighting rheostat button. Adjusts the level of the instrument and controls illumination and the interior mood
lighting.
4. Display screen.5. Fuel level. Indicates the quantity of fuel remaining in
the tank. 6. Display management button Alternates display between range and trip mileage recorder. Ser vicing information. Resets the selected function to zero (trip distance recorder or ser vice indicator).
For more information, refer to the paragraph relating to the button or function and its associated display.

25Instruments and controls
Screen
E. Ser vice indicator (miles or km), then Total mileage recorder These two functions are displayed successively when switching on the ignition F. Engine oil level indicator Appears a few seconds after switching on the ignition, then disappears.
A. Speed limiter (mph or km/h) or Cruise control.B. Gear change indicator.C. Automatic gearbox information.D. Range (miles or km) or Trip mileage recorder.

System which informs the driver when the next ser vice is due, in accordance with the manufacturer's ser vicing schedule. The point at which the ser vice is due is calculated from the last indicator zero reset. It is determined by two parameters: - the distance travelled, - the time elapsed since the last ser vice.
Service indicator
More than 600 miles (1 000 km) remain before the next service is due
For 5 seconds after the ignition is switched on, the spanner symbolising the ser vice operations comes on. The distance recorder display line indicates the distance remaining before the next ser vice is due. Example: 4 800 km remain before the next ser vice is due. For 5 seconds after the ignition is switched on, the display indicates:
Less than 600 miles (1 000 km) remain before the next service is due
Example: 400 miles (900 km) remain before the next ser vice is due. For 5 seconds after the ignition is switched on, the display indicates:
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains on to indicate that a ser vice must be carried out soon. 5 seconds after the ignition is switched on, the spanner is switched off ; the distance recorder off
resumes its normal operation. The display then indicates the total and trip distances.

37Instruments and controls
5 seconds after the ignition is switched on, the distance recorder resumes its normal operation. The spanner remains lit .
The distance remaining may be weighted by the time factor, depending on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded the two year ser vice inter val.
Service indicator zero reset
After each ser vice, the ser vice indicator must be reset to zero. The procedure for resetting to zero is as follows:  switch off the ignition,  press and hold the trip distance recorder zero reset button,  switch on the ignition; the distance recorder display begins a countdown,  when the display indicates "=0" , release the button; the spanner disappears.
Following this operation, if you wish to disconnect the battery, lock the vehicle and wait at least five minutes for the zero reset to be taken into account.
Retrieving the service information
You can access the ser vice information at any time.  Press the trip distance recorder zero reset button. The ser vice information is displayed for a few seconds, then disappears.
Service overdue
For 5 seconds after the ignition is switched on, the spanner flashes to indicate that the ser vice must be carried out as soon as possible. Example: the ser vice is overdue by 300 km. For 5 seconds after the ignition is switched on, the display indicates:

Instruments and controls
System which measures the total distance travelled by the vehicle during its life. The total and trip distances are displayed for thir ty seconds when the ignition is switched off, when the driver's door is opened and when the vehicle is locked or unlocked.
Total distance recorder
System which measures a distance travelled during a day or other period until it is reset to zero by the driver.  With the ignition on, press the button until zeros appear.
Trip distance recorder
System for manual adjustment of the brightness of the instruments and controls in relation to the exterior brightness.
Lighting rheostat
Activation
When the lighting is on:  press the button to change the brightness
of the instruments and controls,  when the level of brightness required is reached, release the button.
Deactivation
When the lighting is off, or in day mode on vehicles fitted with LED lamps, pressing the button does not have any effect.

Black panel
System allowing cer tain displays to be switched off for night driving. The instrument panel remains lit with only the vehicle speed and cruise control or speed limiter information, if in use. If there is an aler t or a change in a function or to a setting, the black panel mode is interrupted.
Activation
 With the lighting on, press the left hand button of the instrument panel several times to progressively reduce the dashboard lighting level.  Press the button again to reduce the lighting to the minimum level and switch off the interior mood lighting.  Press the button again to activate the black panel.