2009.5 Citroen C5 brake

IX
!
128
D R I V I N G

 Immobilise the vehicle by plac-
ing a chock at the front or at the
rear of one of the rear wheels.

 Open the lower compartment of
the centre armrest by pulling it.

 Ensure that the cup holder B is
folded away.

 Remove the rubber mat covering
the base of the armrest. This strap does not permit
application of the parking
brake.
To re-engage the electric parking
brake (after rectifying the malfunc-
tion or battery failure), give a long
pull on the control A until the park-
ing brake warning lamp (!) fl ashes
on the instrument panel then give a
second long pull until this warning
lamp is lit permanently.
The time required for the subse-
quent application may be longer
than during normal operation.
It is essential that the ignition is
not switched on until the parking
brake has re-engaged (fl ashing of
the warning lamp (!) on the instru-
ment panel then warning lamp lit
permanently) to avoid damage to
the parking brake.
Take care not to allow moisture or
dust in the proximity of the diagnos-
tic socket D which is essential for
the maintenance of your vehicle.

 Release the strap from its loca-
tion C .

 Pull the strap to release the
brake. A loud knock confi rms the
release of the brake.

 Take care to put the strap
back in its location C correctly.
Otherwise, it will no longer be
possible to apply the brake.
Consult a CITROËN dealer.

 Put the rubber mat back in place
on the base of the armrest.

IX
!
129
D R I V I N G
If any of these instances arises, contact a CITROËN dealer as soon as possible.

SITUATION
CONSEQUENCES

1 Electric parking brake fault and display of
message "
Parking brake faulty " and the fol-
lowing warning lamps: If the electric parking brake fault warning lamp and the servi
ce
warning lamp light up, position the vehicle in a safe loca tion (on fl at
ground, with a gear engaged).

2 Display of the messages "
Parking brake
faulty " and " Anti roll-back
fault " and of the
following warning lamps: - The automatic functions are deactivated.
- The hill start assist is unavailable.
- The electric parking brake is only available manually.

3 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the follow-
ing warning lamp: - Manual release of the electric parking brake is unavailabl
e.
- The hill start assist is unavailable.
- The automatic functions and manual application are stil l avai-
lable.
Operating anomalies

IX
130
D R I V I N G

SITUATION
CONSEQUENCES

4 Display of messages "
Parking brake faulty "
and " Anti roll-back
fault " and of the follow-
ing warning lamps:
and/or fl ashing - The automatic functions are deactivated.
- The hill start assist is unavailable.
To apply the electric parking brake:

 Immobilise the vehicle and switch off the ignition

 Pull the control lever for at least 5 seconds or until maximum
application.

 Switch on the ignition and check that the electric parking brake
warning lamps are on.
- Application may take longer than in normal operation.
- If warning lamp (!) fl ashes or if the warning lamps do not come
on when the ignition is switched on, this method does not work.
Have it checked by a CITROËN dealer.
To release the electric parking brake:

 Switch on the ignition.

 Push the control lever and hold it for approximately 3 seconds.

5 Display of message "
Parking brake control
faulty – automatic mode activated " and the
following warning lamps:
and/or fl ashing - Only the functions for automatic application on switchi
ng off the
engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake a nd
dynamic emergency braking are unavailable.

6 Display of message "
Parking brake faulty "
and of the following warning lamp:
fl ashing - Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:

 Wait approximately 3 minutes.

 After 3 minutes, if the warning lamp is still fl ashing, try to reini-
tialise the parking brake, either by pushing and releasing th e
control A while pressing the brake pedal or by means of a long
pull on control A .

7 Battery fault - Lighting of the battery warning lamp ma
kes it essential to stop
the vehicle as soon as traffi c allows. Stop and immobilise your
vehicle.
- Apply the electric parking brake before switch ing off the engine.

IX!
131
D R I V I N G
HILL START ASSIST
System which keeps your vehicle
immobilised temporarily (approxi-
mately 2 seconds) when starting on
a gradient, the time it takes to move
your foot from the brake pedal to the
accelerator pedal.
This function is only active when:
- the vehicle is completely station-ary, with your foot on the brake
pedal,
- in certain conditions on a gradi- ent,
- with the driver’s door closed.
The hill start assist function cannot
be deactivated. Operation

On an ascending
gradient
, with
the vehicle stationary, the vehicle
is held for a brief moment when
you release the brake pedal:
- provided you are in fi rst gear or neutral on a manual gearbox,
- provided you are in D or M on an
automatic gearbox.
On a descending
gradient
, with
the vehicle stationary and reverse
gear engaged, the vehicle is held
for a brief moment when you re-
lease the brake pedal.
Do not exit the vehicle while
it is being held in the hill start
assist phase.
If you need to exit the vehicle
with the engine running, manually
apply the parking brake and en-
sure that the parking brake warning
lamp (on the instrument panel) and
the warning lamp P (on the control
lever A ) are permanently on.

IX
!
134
D R I V I N G
Mode selection Displays on the instrument panel

 automatic mode: gear lever in
position D ,

 sequential mode: gear lever in
position M ,

 SPORT mode: gear lever in po-
sition D and button A pressed,

 SNOW mode: gear lever in posi-
tion D and button B pressed. The position of the gear lever and
the driving mode are displayed on
the instrument panel dial
C .
A position grille associated with the
gear lever allows you to view the se-
lected position.
For safety:
- position P can be disen-
gaged only if you press the
brake pedal,
- when a door is opened, an au- dible signal is heard if the gear
lever is not in position P ,
- always make sure that the gear lever is in position P before you
leave your vehicle.
If the gearbox is in position P but
the position of the gear lever is dif-
ferent, reposition the gear lever on

P so that you can start the vehicle.
AUTOMATIC GEARBOX
Automatic gearbox which offers a
choice between the comfort of fully
automatic operation, enhanced by
the sport and snow programmes, or
manual gear changing.
Four driving modes are provided:
- automatic operation for elec-
tronic control of the gears by the
gearbox,
- the SPORT programme for a
more dynamic driving style,
- the SNOW programme to im-
prove driving when the grip is
poor,
- manual operation for sequen-
tial changing of the gears by the
driver.

IX
!
135
D R I V I N G
Never select positions P or R
if the vehicle is not stationary.
If, while the vehicle is moving, po-
sition N is engaged inadvertently,
allow the engine to idle before en-
gaging position D or M .
Moving off

 To start the engine, the gear le-
ver must be in position P or N .

 Operate the starter.

 When the engine is running,
place the gear lever on R , D or

M as required.

 Check, in the instrument panel,
the position engaged.

 Release the brake pedal and ac-
celerate.

 To avoid a possible difference
between the position of the gear
lever and the actual position of
the gearbox, always exit from
position P with the ignition on
and brake pedal applied.
Otherwise, when the ignition is on or
the engine is running:

 reposition the gear lever in posi-
tion P ,

 put your foot on the brake pedal
and then select the gear you
want. Park
This position of the gear le-
ver is used to prevent the
vehicle from moving when
you are stationary.

 To select position P , move the
gear lever back to the highest
position (towards R ), then push
it forwards and then to the left.

 To exit position P , move the gear
lever to the right and then to the
position you want.

 Only engage this position when
the vehicle is completely sta-
tionary. In this position, the front
wheels are locked. Make sure
that the gear lever is correctly
positioned. Reverse gear
Only engage this position
when the vehicle is station-
ary. To prevent snatching,
do not accelerate too soon
after selection.
Neutral Never select position N if
the vehicle is moving.

IX
!
137
D R I V I N G
SPORT and SNOW
programmes
SPORT programme "S"
These two special programmes sup-
plement the automatic operation in
very particular conditions of use.

 With the gear lever in po-
sition D and the engine
running, press button A . SNOW programme "
 "

 With the gear lever in position D
and the engine running, press
button B .
The gearbox adapts to driving on
slippery roads.
This programme makes moving off
easier and improves traction in con-
ditions of poor grip.

 appears on the instru-
ment panel.
The gearbox automatically favours a
dynamic driving style.

S appears on the instrument panel. Return to automatic operation

 At any time, press the button se-
lected again to exit from the pro-
gramme engaged and return to
auto-adaptive mode. A strong snatch may be felt
when selecting
R for reverse
gear.
In the event of a malfunction, the
gearbox is blocked in one gear;
do not exceed a speed of 62 mph
(100 km/h).
Do not turn off the engine while the
gear selector is in position D or R .
Never press the accelerator and
brake pedals simultaneously.
Braking and acceleration should
be done with the right foot only.
Pressing both pedals simultane-
ously may damage the gearbox.
Consult a CITROËN dealer.

IX
141
D R I V I N G
In the event of a steep descent or
under excessive acceleration, the
speed limiter (which does not act
on the brakes) may not be able to
prevent the vehicle from exceeding
the programmed speed.
Use of a fl oor mat other than that
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
are fi tted with a 3rd fi xing located in
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption

 Press on button 3 .
This action causes the information

"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
memorised maximum speed which
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
of-travel switch. In order to exceed
the memorised maximum speed at
any time, you can press the pedal
all the way down. While the speed
is being exceeded, the speed dis-
played in zone
A will fl ash. You have
only to release the accelerator pedal
to return below the maximum speed,
to restore the function.
The speed will also fl ash if the speed
limiter is not able to prevent the vehi-
cle from exceeding the programmed
speed (e.g. on a steep descent or
under excessive acceleration).
To reactivate the speed limiter, re-
lease the accelerator to slow to a
speed lower than the programmed
speed. Return to normal driving

 Either press on button 5 .

 Or select the speed limiter func-
tion.

 Or stop the engine.
Operating fault
If there is a malfunction, a mes-
sage is displayed accompanied by
an audible signal and lighting of the

SERVICE warning lamp.
Have it checked by a CITROËN
dealer.