2009.5 Citroen C3 PICASSO DAG Owner's Manual

!
!
126
PRACTICAL INFORMATION
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb.
1. Direction indicators
(H21W amber).

2. Dipped
beam
headlamps
(H7-55W).

3. Main beam headlamps (H1-55W).

4. Sidelamps
(W5W).

5. Foglamps
(PSX24W).
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:

 do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,

 use a sponge and soapy water,

 when using a high pressure
washer on persistent marks, do
not direct at the lamps or their
outlines for too long, so as not
to damage their protective coat-
ing and seals. Front lamps

 Do not touch the bulb directly
with your fi ngers, use lint-free
cloths.
Changing a halogen bulb should
only be done after the headlamp
has been switched off for a few
minutes (risk of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order
not to damage the headlamp.

i
!
i
127
PRACTICAL INFORMATION
Changing direction indicator bulbs
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cations and colour.

 Remove the plastic protective cover.

 Pull the bulb-holder and replace the
bulb.
To refi t, carry out these operations in
reverse order.
When refi tting, close the plastic
cover carefully to ensure the sealing
of the headlamp. If either of the direction indicator
warning lamps is fl ashing quickly,
one of the bulbs is faulty.
Changing main beam headlamp
bulbs

 Remove the protective plastic cover
by pulling on the tab.

 Disconnect the bulb connector.

 Move the springs to release the
bulb.

 Remove the bulb and change it.
To refi t, carry out these operations in
reverse order.
Changing sidelamp bulbs

 Remove the protective plastic cover
by pulling on the tab.

 Pull the bulb-holder.

 Remove the bulb and replace it.
To refi t, carry out these operations in
reverse order.
Changing dipped headlamp bulbs

 Remove the protective plastic cover
by pulling on the tab.

 Turn the bulb-holder by a quarter
turn.

 Remove the bulb and change it.
To refi t, carry out these operations in
reverse order.

i
i
128
PRACTICAL INFORMATION
Changing integrated direction
indicator side repeaters
Contact a CITROËN dealer to obtain
replacement repeaters.

 Insert a screwdriver on the edge of
the repeater.

 Tilt the screwdriver to extract the
repeater and remove it.

 Disconnect the repeater connector.
When removing:
- be careful not to damage the paint- work of your vehicle with the screw-
driver,
- do not allow the wire and the connector to slide inside the wing.
To refi t, carry out these operations in
reverse order.
If you experience any diffi culty
in replacing bulbs, contact your
CITROËN dealer. Changing front foglamp bulbs
To obtain them, contact your CITROËN
dealer.

 Remove the grille located under the
foglamp.

 Disconnect the bulb holder connec-
tor, by pressing on the tab.

 Remove the bulb-holber by pressing
on the 2 clips (at the top and the
bottom).
To refi t, carry out these operations in
reverse order.
If you experience any diffi culty
in replacing bulbs, contact your
CITROËN dealer.

129
PRACTICAL INFORMATION
Rear lamps

1. Stop lamps
/
sidelamps

(12VP21/5 W).

2. Foglamp,
left-hand side
(PR21W)
Reversing
lamp,
right-hand side
(P21W).

3. Direction indicators (
P21W
) Changing stop lamp/sidelamp and
direction indicator bulbs

 unscrew the two lamp unit fi xing
bolts,

 extract the lamp unit carefully pull-
ing it straight out,
 turn the bulb holder a quarter turn,

 remove the faulty bulb and replace
it.
To refi t, carry out these operations in
reverse order.

PRACTICAL INFORMATION
Changing fog/reversing lamp bulbs

 open the boot,


press on the tabs using 2 screwdrivers,

 disconnect the lamp unit connector,

 turn the bulb holder by a quarter
turn,

 remove the bulb and replace it.
To refi t, carry out these operations in
reverse order. Changing the third stop lamp bulbs
(4 x W 5 W bulbs)

 open the boot,

 remove the two plugs located on the
boot inner panel,

 press on the body of the lamp with
2 screwdrivers to remove it from its
housing,

 turn the corresponding bulb-holder
a quarter turn,

 pull the bulb and replace it.
To refi t, carry out these operations in
reverse order. Changing the number plate lamp
bulbs (W5W)

 insert a thin screwdriver into one of
the lens' exterior holes,

 push it outwards to unclip.

 remove the lens.

 pull the bulb and replace it.
To refi t, carry out these operations in
reverse order.

131
PRACTICAL INFORMATION
Interior lighting
Interior lamps (1/W5W)
Detach the cover of the interior lamp 1
with a thin screwdriver, close to the but-
ton, to access the faulty bulb.
Map reading lamps (2/W5W)
Detach the cover of the interior lamp. To
access the faulty bulb, detach the parti-
tion for the reading lamp 2 concerned,
as necessary. Footwell lamps (W5W)
Unclip the cover using a thin screw-
driver to access the faulty bulb.
Boot lamps (W5W)
Detach the unit by pushing it rear-
wards. Torch (Krypton 3.6 V)

 Open the tab.

 Push with a fl at screwdriver in the
hole under the tab and recover the
bulb unit.

 Open the bulb unit fully to change
the bulb.
Exterior mirror lamps (W5W)
Unclip the cover using a thin screw-
driver to access the faulty bulb.

i
!
132
PRACTICAL INFORMATION CITROËN will not accept respon-
sibility for the cost incurred in
repairing your vehicle or for recti-
fying malfunctions resulting from
the installation of accessories not
supplied and not recommended
by CITROËN and not installed in
accordance with its instructions,
in particular when the combined
consumption of all of the addition-
al equipment connected exceeds
10 milliamperes.
Installing electrical accessories
Your vehicle's electrical system is
designed to operate with standard
or optional equipment.
Before installing other electrical
equipment or accessories on your
vehicle, contact a CITROËN dealer.
CHANGING A FUSE
Procedure for replacing a faulty fuse
with a new fuse to rectify a failure of the
corresponding function.
Access to tools
The extraction pliers and the spare
fuse storage compartment are installed
on the back of the dashboard fusebox
cover.
For access to them:

 unclip the cover by pulling on the
side,

 remove the cover completely,

 remove the pliers. Changing a fuse
Before changing a fuse, the cause of
the failure must be identifi ed and recti-
fi ed.

 Identify the faulty fuse by checking
the condition of its fi lament.

 Use the special pliers to extract the
fuse from its housing.

 Always replace the faulty fuse with a
fuse of the same rating.

 Check the correspondence between
the number etched on the box, the
rating etched on the fuse and the
tables below.
Correct Incorrect

133
PRACTICAL INFORMATION
Dashboard fuses
The fusebox is placed in the lower sec-
tion of the dashboard (left-hand side).
Access to fuses

 refer to the paragraph "Access to
tools". Fuse tables

Fuse N° Rating Functions

FH36 5 A Trailer relay unit.

FH37 15 A Trailer accessories socket supply.

FH38 20 A Aftermarket navigation.

FH39 20 A Heated seats.

FH40 30 A Trailer relay unit.

Fuse N° Rating Functions

F1 15 A Rear wiper.

F2 - Not used.

F3 5 A Airbags and pretensioners control unit.

F4 10 A Steering wheel angle sensor, air conditioning,
clutch switch, particle fi lter pump, diagnostic
socket, airfl ow meter.

F5 30 A Electric window switch panel, passenger's electric
window control, front electric window motor.

F6 30 A Rear electric window motor and driver's electric
window motor.

F7 5 A Courtesy and front map reading lamps, glove box
lighting, torch, rear reading lamps.