2009.5 Citroen C3 Owner's Manual

11
PRACTICAL INFORMATION
Engine compartment fusebox
The fusebox is placed in the engine
compartment near the battery (left-hand
side).
Access to the fuses

 Unclip the cover.

 Change the fuse (see correspond-
ing paragraph).

 When you have fi nished, close the
cover carefully to ensure the sealing
of the fuse box. Fuse table

Fuse N° Rating Functions

F1 20 A Engine control unit supply, cooling fan unit control
relay, multifunction engine control main relay,
injection pump (Diesel).

F2 15 A Horn.

F3 10 A Front/rear wash-wipe.

F4 20 A Daytime running lamps.

F5 15 A Diesel heater (Diesel), particle fi lter additive pump
(Diesel), air fl ow sensor (Diesel),
EGR electrovalve (Diesel), fuel pump (1.1i and 1.4i), blow-by heater
and electrovalves (VTi).

F6 10 A ABS/ESP control unit, secondary stop switch.

F7 10 A Electric power steering, automatic gearbox.

F8 25 A Starter control.

F9 10 A Switching and protection unit (Diesel).

F10 30 A Fuel heater (Diesel), blow-by heater (1.1i, 1.4i and
Diesel), fuel pump (VTi), injectors and ignition coils
(petrol), electronic thermostat and canister purge
electrovalve (1.1i and 1.4i).

F11 40 A Heater blower.

11
PRACTICAL INFORMATION

Fuse N° Rating Functions

F12 30 A Windscreen wipers slow/fast speed.

F13 40 A Built-in systems interface supply (ignition positive).

F14 30 A Valvetronic supply (VTi).

F15 10 A Right-hand main beam headlamps.

F16 10 A Left-hand main beam headlamps.

F17 15 A Left-hand dipped beam headlamps.

F18 15 A Right-hand dipped beam headlamps.

F19 15 A Oxygen sensors and electrovalves (VTi),
electrovalves (Diesel), EGR electrovalve (Diesel).

F20 10 A Pumps, electronic thermostat (VTi) water in fuel
sensor (Diesel).

F21 5 A Fan assembly control supply, ABS/ESP.

11
PRACTICAL INFORMATION
Table of maxi-fuses
Fuse N° Rating
Functions

MF1 * 60 A Fan assembly.

MF2 * 30 A ABS/ESP pump.

MF3 * 30 A ABS/ESP electrovalves.

MF4 * 60 A Built-in Systems Interface (BSI) supply.

MF5 * 60 A Built-in Systems Interface (BSI) supply.

MF6 * - Not used.

MF7 * - Passenger compartment fusebox.

MF8 * - Not used.
* The maxi-fuses provide additional protection for the e lectrical systems. All work on the maxi-fuses must be carried out by a
CITROËN dealer.

11
PRACTICAL INFORMATION
BATTERY
Procedure for charging your battery
when it is fl at or for starting the engine
using another battery.
The battery is located under the bonnet.
To gain access to it:

 open the bonnet using the interior
lever, then the exterior lever,

 secure the bonnet strut,

 remove the plastic cover by pulling
on its grip for access to the two ter-
minals,

 unclip the fuse box to remove the
battery, if necessary.
Access to the battery
Starting using another battery

 Connect the red cable to the posi-
tive terminal (+) of the fl at battery A ,
then to the positive terminal (+) of
the slave battery B .

 Connect one end of the green or black
cable to the negative terminal (-)
of the slave battery B .

 Connect the other end of the green
or black cable to the negative termi-
nal (-) of the fl at battery A .

 Start the slave vehicle.

 Operate the starter of the broken
down vehicle and let the engine
run.

 Wait until the engine returns to idle
and disconnect the cables.

11
PRACTICAL INFORMATION
Charging the battery using a
battery charger

 Disconnect the battery from the ve-
hicle.

 Follow the instructions for use pro-
vided by the manufacturer of the
charger.

 Reconnect starting with the nega-
tive terminal (-).

 Check that the terminals and connec-
tors are clean. If they are covered with
sulphate (whitish or greenish deposit),
remove them and clean them.
It is advisable to disconnect
the battery if the vehicle is to
be left unused for more than
one month. Do not disconnect the terminals
while the engine is running.
Do not charge the batteries with-
out disconnecting the terminals
fi rst.
Batteries contain harmful sub-
stances such as sulphuric acid and
lead. They must be disposed of in
accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control bat-
teries and vehicle batteries to a
special collection point.
Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the
doors before disconnecting the
battery.
Following reconnection of the
battery
Following reconnection of the
battery, switch on the ignition
and wait 1 minute before start-
ing to permit initialisation of the
electronic systems. However,
if minor problems persist fol-
lowing this operation, contact a
CITROËN dealer.
Referring to the correspond-
ing section, you should yourself
reinitialise:
- the remote control key,
- the GPS satellite navigation system.
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions according to the level of
charge remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as the air condi-
tioning, the heated rear screen...
The deactivated functions are reactivat-
ed automatically as soon as conditions
permit.

11
PRACTICAL INFORMATION
Charging the battery using a
battery charger

 Disconnect the battery from the ve-
hicle.

 Follow the instructions for use pro-
vided by the manufacturer of the
charger.

 Reconnect starting with the nega-
tive terminal (-).

 Check that the terminals and connec-
tors are clean. If they are covered with
sulphate (whitish or greenish deposit),
remove them and clean them.
It is advisable to disconnect
the battery if the vehicle is to
be left unused for more than
one month. Do not disconnect the terminals
while the engine is running.
Do not charge the batteries with-
out disconnecting the terminals
fi rst.
Batteries contain harmful sub-
stances such as sulphuric acid and
lead. They must be disposed of in
accordance with regulations and
must not, in any circumstances, be
discarded with household waste.
Take used remote control bat-
teries and vehicle batteries to a
special collection point.
Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
the battery.
Close the windows and the
doors before disconnecting the
battery.
Following reconnection of the
battery
Following reconnection of the
battery, switch on the ignition
and wait 1 minute before start-
ing to permit initialisation of the
electronic systems. However,
if minor problems persist fol-
lowing this operation, contact a
CITROËN dealer.
Referring to the correspond-
ing section, you should yourself
reinitialise:
- the remote control key,
- the GPS satellite navigation system.
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions according to the level of
charge remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates
certain functions, such as the air condi-
tioning, the heated rear screen...
The deactivated functions are reactivat-
ed automatically as soon as conditions
permit.

11
PRACTICAL INFORMATION
If the telephone is being used
at the same time on the MyWay
audio navigation system, it will
be interrupted after 10 minutes. A fl at battery prevents the engine
from starting (refer to the corre-
sponding paragraph).
ENERGY ECONOMY MODE
System which manages the period of
use of certain functions to conserve a
suffi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
headlamps, courtesy lamps, etc. for a maxi-
mum combined period ofthirty minutes.
Switching to economy mode
Once this period has elapsed, a message ap-
pears on the multifunction screen indicating
that the vehicle has switched to economy mode
and the active functions are put on standby.
Exiting economy mode
These functions are reactivated auto-
matically the next time the vehicle is
driven.

 In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be dou-
ble the period for which the engine is left
running. However, this period will always
be between fi ve and thirty minutes.
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.
Before removing a front wiper
blade

 Within one minute after switching off
the ignition, operate the wipers stalk
to position the wiper blades in the
centre of the windscreen.
Removing a front or rear wiper
blade

 Raise the corresponding wiper arm.

 Unclip the wiper blade and remove it.
Fitting a front or rear wiper blade

 At the front, check the size of the
wiper blade as the shorter blade is
fi tted on the right-hand side of the
vehicle.

 Put the corresponding new wiper
blade in place and clip it.

 Fold down the wiper arm carefully.
After fitting a front wiper blade

 Switch on the ignition.

 Operate the wipers stalk again to
park the wiper blades.
This period may be greatly re-
duced if the battery is not fully
charged.

11
PRACTICAL INFORMATION
Failure to observe this special
condition could result in damage
to certain braking components
and the absence of braking as-
sistance the next time the engine
is started. When towing with all four wheels
on the ground, always use a
towing bar.
When towing with only two wheels
on the ground, always use profes-
sional lifting equipment.
When towing with the engine off,
there is no longer any assistance
for braking or steering.
TOWING THE VEHICLE
Procedure for having your vehicle towed
or for towing another vehicle using a re-
movable towing eye.
Access to the tools
The towing eye is installed in the boot
under the fl oor.
To gain access to it:

 open the boot,

 raise the fl oor,

 remove the polystyrene storage box,

 remove the towing eye from the
holder. Towing your vehicle

 On the front bumper, unclip the cover
by pressing at the bottom.

 Screw the towing eye in fully.

 Install the towing bar.

 Switch on the hazard warning lamps
on the towed vehicle.

 Place the gear lever in neutral (posi-
tion N for an automatic gearbox). Towing another vehicle

 On the rear bumper, unclip the cover
by pressing at the bottom.

 Screw the towing eye in fully.

 Install the towing bar.

 Switch on the hazard warning lamps
on the towed vehicle.