2008 YAMAHA YFM250R oil filter

RIDING YOUR ATV ...................................... 7-1
GETTING TO KNOW YOUR ATV.............. 7-2
RIDE WITH CARE AND GOOD
JUDGEMENT ........................................... 7-2
BE CAREFUL WHERE YOU RIDE ............ 7-8
TURNING YOUR ATV ............................. 7-12
CLIMBING UPHILL .................................. 7-14
RIDING DOWNHILL................................. 7-16
CROSSING A SLOPE.............................. 7-17
CROSSING THROUGH SHALLOW
WATER .................................................. 7-18
RIDING OVER ROUGH TERRAIN .......... 7-20
SLIDING AND SKIDDING ........................ 7-20
WHAT TO DO IF... ................................... 7-21
WHAT TO DO... ....................................... 7-21
PERIODIC MAINTENANCE AND MINOR
REPAIR .......................................................... 8-1
Owner’s manual and tool kit ...................... 8-1
Periodic maintenance chart for the
emission control system .......................... 8-3
General maintenance and lubrication
chart ........................................................ 8-5
Checking the spark plug ............................ 8-9
Engine oil and oil filter element ............... 8-10
Cleaning the air filter element ................. 8-14
Cleaning the spark arrester ..................... 8-18
Adjusting the carburetor .......................... 8-19
Adjusting the engine idling speed ........... 8-20Adjusting the throttle cable free play ........ 8-20
Valve clearance ....................................... 8-21
Checking the front and rear brake
pads ....................................................... 8-22
Checking the brake fluid level .................. 8-23
Changing the brake fluid .......................... 8-25
Checking the front brake lever free
play ........................................................ 8-26
Checking the brake pedal position ........... 8-26
Adjusting the parking brake free play ...... 8-27
Brake light switches ................................. 8-29
Adjusting the clutch lever free play .......... 8-29
Drive chain slack ...................................... 8-30
Lubricating the drive chain ....................... 8-32
Checking and lubricating the cables ........ 8-33
Checking and lubricating the brake and
clutch levers ........................................... 8-33
Checking and lubricating the brake and
shift pedals ............................................. 8-34
Checking the wheel hub bearings ............ 8-34
Lubricating the swingarm pivots .............. 8-34
Lubricating the upper and lower arm
pivots ..................................................... 8-35
Lubricating the steering shaft ................... 8-36
Battery ..................................................... 8-36
Replacing the fuse ................................... 8-37
Replacing a headlight bulb ...................... 8-39
Adjusting a headlight beam ..................... 8-41
Replacing the tail/brake light bulb ............ 8-42

8-10
1
2
3
4
5
6
78
9
10
11

2. Check the spark plug for electrode erosion
and excessive carbon or other deposits, and
replace it if necessary.
To install the spark plug
1. Measure the spark plug gap with a wire thick-
ness gauge and, if necessary, adjust the gap
to specification.2. Clean the surface of the spark plug gasket
and its mating surface, and then wipe off any
grime from the spark plug threads.
3. Install the spark plug with the spark plug
wrench, and then tighten it to the specified
torque.NOTE:
If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque as
soon as possible.
4. Install the spark plug cap.
EBU28881
Engine oil and oil filter element
The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter element cleaned at the intervals speci-
fied in the periodic maintenance and lubrication
chart. Specified spark plug:
NGK/DR7EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
1. Spark plug cap
Tightening torque:
Spark plug:
18 Nm (1.8 m·kgf, 13 ft·lbf)

8-12
1
2
3
4
5
6
78
9
10
11

To change the engine oil (with or without oil
filter element cleaning)
1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min-
utes, and then turn it off.
3. Place an oil pan under the engine to collect
the used oil.
4. Remove the engine oil filler cap, and then re-
move the engine oil drain bolt to drain the oil
from the crankcase.
CAUTION:

ECB00310
When removing the engine oil drain bolt, thecompression spring, oil strainer and O-ring will
fall out. Take care not to lose these parts.
NOTE:

Skip steps 5–9 if the oil filter element is not being
cleaned.
5. Remove the oil filter element cover by remov-
ing the bolts, and then remove the oil filter el-
ement.
6. Clean the oil filter element with solvent.
7. Check the O-rings for damage and replace it if
necessary.
1. Engine oil drain bolt
1

1. Oil filter element cover
2. Bolt
1 2

8-13
1
2
3
4
5
6
78
9
10
11

8. Install the oil filter element and O-ring.
NOTE:

Make sure that the O-ring is properly seated.
9. Install the oil filter element cover by installing
the bolts, and then tighten them to the speci-
fied torque.10. Install the engine oil drain bolt and tighten it to
the specified torque.CAUTION:
ECB00320
Before installing the engine oil drain bolt, be
sure to install the O-ring, compression spring
and oil strainer.
11. Add the specified amount of the recommend-
ed engine oil, and then install and tighten the
engine oil filler cap.
NOTE:

Be sure to wipe off spilled oil on any parts after the
1. Oil filter element
2. O-ring
Tightening torque:
Oil filter element cover bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
1
2
2

Tightening torque:
Engine oil drain bolt:
20 Nm (2.0 m·kgf, 14.5 ft·lbf)
Recommended oil:
See page 10-1.
Oil quantity:
Without oil filter element replacement:
1.25 L (1.32 US qt) (1.10 Imp.qt)
With oil filter element replacement:
1.35 L (1.43 US qt) (1.19 Imp.qt)

8-14
1
2
3
4
5
6
78
9
10
11

engine and exhaust system have cooled down.
CAUTION:

ECB00300

In order to prevent clutch slippage (since the
engine oil also lubricates the clutch), do not
mix any chemical additives. Do not use oils
with a diesel specification of “CD” or oils of
a higher quality than specified. In addition,
do not use oils labeled “ENERGY CONSERV-
ING II” or higher.

Make sure that no foreign material enters the
crankcase.
12. Start the engine, and then let it idle for several
minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.
13. Turn the engine off, wait at least ten minutes,
and then check the oil level and correct it if
necessary.
EBU23702
Cleaning the air filter element
The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean the air filter element more
frequently if you are riding in unusually wet or dustyareas.
NOTE:

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.
1. Remove the seat. (See page 4-10.)
2. Remove the air filter case cover by unhooking
the holders.
1. Air filter case check hose
1

8-16
1
2
3
4
5
6
78
9
10
11

7. Wash the sponge material gently but thor-
oughly in solvent.
WARNING

EWB01940
Always use parts cleaning solvent to clean the
sponge material. Never use low-flash-point
solvents or gasoline to clean the sponge mate-
rial because the engine could catch fire or ex-
plode.
8. Squeeze the excess solvent out of the sponge
material and let it dry.CAUTION:

ECB00440
Do not twist the sponge material when squeez-
ing it.
9. Check the sponge material and replace it if
damaged.
10. Apply a quality foam air filter oil to the sponge
material.
NOTE:

The sponge material should be wet but not drip-
ping.
11. Pull the sponge material over the air filter ele-
ment frame.
1. Sponge material
2. Air filter element frame
1
2

10-2
1
2
3
4
5
6
7
8
910
11

Engine oil quantity:
Without oil filter element replacement:
1.25 L (1.32 US qt) (1.10 Imp.qt)
With oil filter element replacement:
1.35 L (1.43 US qt) (1.19 Imp.qt)
Air filter:
Air filter element:
Wet element
Fuel:
Recommended fuel:
Regular unleaded gasoline only (EUR)
Unleaded gasoline only (AUS)(NZL)
Fuel tank capacity:
9.0 L (2.38 US gal) (1.98 Imp.gal)
Fuel reserve amount:
1.0 L (0.26 US gal) (0.22 Imp.gal)
Carburetor:
Manufacturer:
MIKUNI
Type x quantity:
BSR29 x 1
Spark plug (s):
Manufacturer/model:
NGK/DR7EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:
Wet, multiple-disc
Operation:
Left hand operation
Transmission:
Primary reduction system:
Spur gear
Primary reduction ratio:
76/22 (3.455)
Secondary reduction system:
Chain drive
Secondary reduction ratio:
38/14 (2.714)
Transmission type:
Constant mesh 5-speed
Operation:
Left foot operation
Gear ratio:
1st:
37/13 (2.846)
2nd:
33/18 (1.833)
3rd:
29/21 (1.381)
4th:
27/24 (1.125)
5th:
28/29 (0.966)
Chassis:
Frame type:
Steel tube frame
Caster angle:
6.0 °
Trail:
23.0 mm (0.91 in)

INDEX
A
Accessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-14
B
Battery .......................................................................... 8-36
Brake and clutch levers, checking and lubricating ....... 8-33
Brake and shift pedals, checking and lubricating ......... 8-34
Brake fluid, changing.................................................... 8-25
Brake fluid level, checking............................................ 8-23
Brake lever ..................................................................... 4-5
Brake lever free play, checking the front ...................... 8-26
Brake light switches ..................................................... 8-29
Brake pads, checking the front and rear ...................... 8-22
Brake pedal .................................................................... 4-5
Brake pedal position, checking .................................... 8-26
Brakes, front and rear .................................................... 5-3
C
Cables, checking and lubricating ................................. 8-33
Carburetor, adjusting.................................................... 8-19
Chassis fasteners........................................................... 5-7
Cleaning ......................................................................... 9-1
Clutch lever .................................................................... 4-4
Clutch lever free play, adjusting ................................... 8-29
D
Drive chain ..................................................................... 5-4
Drive chain, lubricating ................................................. 8-32Drive chain slack .......................................................... 8-30
E
Engine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-20
Engine oil ....................................................................... 5-3
Engine oil and oil filter element .................................... 8-10
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-2
F
Fuel ........................................................................ 4-7
,
5-3
Fuel cock ........................................................................ 4-8
Fuel tank cap.................................................................. 4-7
Fuse, replacing............................................................. 8-37
H
Handlebar switches ........................................................ 4-2
Headlight beam, adjusting............................................ 8-41
Headlight bulb, replacing.............................................. 8-39
I
Identification numbers .................................................. 11-1
Indicator light .................................................................. 4-1
Instruments, lights and switches .................................... 5-7
K
Key identification number ............................................. 11-1
L
Label locations ............................................................... 2-1