2008 YAMAHA XMAX 125 drain bolt

EAU10410
Left view
DESCRIPTION
2-1
2
1. Fuel tank cap (page 3-11)
2. Owner’s tool kit (page 6-1)
3. V-belt case air filter cover (page 6-15)
4. Rear storage compartment (page 3-16)
5. Air filter case cover (page 6-15)6. Spring preload adjusting ring (page 3-17)
7. Final transmission oil filler cap (page 6-13)
8. Engine oil drain bolt (page 6-10)
9. Sidestand (page 3-18)
1B9-F8199-E2.qxd 13/11/07 12:18 Página 13

1. Engine oil filler cap
2. Maximum level mark
3. Minimum level mark
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (wit-
hout screwing it in), and then
remove it again to check the oil
level.
NOTE:
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level.5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil (with or
without oil filter element
replacement)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and the engine oil drain bolt to
drain the oil from the crankcase.1. Engine oil drain bolt
4. Check the drain bolt washer for
damage and replace it if neces-
sary.
1. Engine oil drain bolt
2. Washer
NOTE:
Skip steps 5 to 9 if the oil filter ele-
ment is not being replaced.
5. Remove the oil filter element
cover by removing the bolts.
1. Oil filter element cover
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
6
1B9-F8199-E2.qxd 13/11/07 12:18 Página 52

6. Remove the oil filter element and
o-ring.
1. Oil filter element
2. O-ring
3. Oil filter element cover
7. Check the O-ring for domage
and replace it if necessary.
8. Install the new oil filter element
and an O-ring.
9. Install the oil filter element cover
by installing the bolts, then tigh-
tening them to the specified tor-
que.
NOTE:
Make sure that the O-ring is properly
seated.
10. Install the washer and the engine
oil drain bolt, and then tighten the
drain bolt to the specified torque.
NOTE:
Make sure that the washer is properly
seated.
11. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil
filler cap.
NOTE:
Be sure to wipe off spilled oil on any
parts after the engine and exhaust
system have cooled down.
ECA11670
CAUTION:
●Do not use oils with a diesel
specification of “CD” or oils of
a higher quality than specified.
In addition, do not use oils
labeled “ENERGY CONSER-
VING II” or higher.
●Be sure no foreign material
enters the crankcase.
12. Start the engine, and then let it
idle for several minutes while
checking it for oil leakage. If oil is
leaking, immediately turn the
engine off and check for the cau-
se.
13. Turn the engine off, and then
check the oil level and correct it if
necessary.
14. Reset the oil change indicator.
(See page 3-6.)
Recommended engine oil:
See page 8-1.
Oil change quantity:
Without oil filter element replace-
ment
1.40 L (1.48 US qt) (1.23 Imp.qt)
With oil filter element replacement
1.50 L (1.59 US qt) (1.32 Imp.qt)
Tightening torque:
Engine oil drain bolt:
32 Nm (3.2 m·kgf, 23 ft·lbf)
Tightening torque:
Oil filter cover bolt::
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
6
1B9-F8199-E2.qxd 13/11/07 12:18 Página 53

EAU20061
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final trans-
mission oil must be changed as
follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Start the engine, warm up the
final transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the centers-
tand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the oil filler cap and
drain bolt to drain the oil from the
final transmission case.
1. Final transmission oil filler cap
2. O-ring
5. Install the final transmission oil
drain bolt, and then tighten it to
the specified torque.
1. Final transmission oil drain bolt
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten
the oil filler cap.
EWA11310
s s
WARNING
●Make sure that no foreign
material enters the final trans-
mission case.
●Make sure that no oil gets on
the tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.21 L (0.22 US qt) (0.18 Imp.qt)
Tightening torque:
Final transmission oil drain bolt:
20 Nm (2.0 m·kgf, 14 ft·lbf)
PERIODIC MAINTENANCE AND MINOR REPAIR
6-13
6
1B9-F8199-E2.qxd 13/11/07 12:18 Página 54