2008 YAMAHA VITY 125 clock

INSTRUMENT AND CONTROL FUNCTIONS
3-6
3
EAU12950
Rear brake lever The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handle-
bar grip.
EAU45390
Fuel tank cap To remove the fuel tank cap
1. Open the seat. (See page 3-8.)
2. Open the fuel tank cap lid.
3. Turn the fuel tank cap counter-
clockwise and pull it off.
To install the fuel tank cap
1. Insert the fuel tank cap into the
tank opening and turn it clockwise
until the“” marks on the cap
and tank are aligned.
2. Close the fuel tank cap lid.
3. Close the seat.
WARNING
EWA11090
Make sure that the fuel tank cap isproperly closed before riding.
1. Rear brake lever
1
1. Fuel tank cap lid
2. Fuel tank cap
2
1
U4P7E1E0.book Page 6 Wednesday, December 12, 2007 9:37 AM

INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
EAU13443
Catalytic converters This vehicle is equipped with catalytic
converters in the exhaust system.
WARNING
EWA10860
The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-ing any maintenance work.CAUTION:
ECA16490
The following precautions must be
observed to prevent a fire hazard or
other damages.

Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converters.


Never park the vehicle near pos-
sible fire hazards such as grass
or other materials that easily
burn.


Do not allow the engine to idletoo long.
EAUT1502
Seat To open the seat
1. Place the scooter on the center-
stand.
2. Insert the key into the main switch,
and then turn it counterclockwise
to the first “OPEN” position. If the
main switch is in the “LOCK” posi-
tion, turn the key counterclockwise
to the second “OPEN” position.NOTE:Do not push inward when turning the
key from “OFF” to “OPEN” or from“LOCK” to “OPEN”.
3. Fold the seat up.To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left un-
attended.
NOTE:Make sure that the seat is properly se-cured before riding.
1. Seat open position
ON
OPEN
OPENP
U
S
HLOCKOFF
ON
OPEN
OPENP
U
S
HLOCKOFF
1
1
U4P7E1E0.book Page 8 Wednesday, December 12, 2007 9:37 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-25
6
EAUT2022
Replacing the fuse The fuse holder is located beside the
battery. Remove panel B to access the
fuse. (See page 6-6.)
If the fuse is blown, replace it as fol-
lows.
1. Turn the key to “OFF” and turn off
all electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
CAUTION:
ECAT1061


Do not use a fuse of a higher
amperage rating than recom-
mended to avoid causing exten-
sive damage to the electrical
system and possibly a fire.


After removing and installing
the main fuse, be sure to turn
the main switch from “ON” to
“OFF” three times in 3 seconds
intervals to initialize the idlespeed control system.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
EAU45501
Replacing the headlight bulb This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.
1. Place the vehicle on the center-
stand.
2. Remove cowling B. (See page
6-6.)
3. Remove the headlight bulb cover.
4. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb
from the headlight unit.
1. Fuse
2. Spare fuseSpecified fuse:
15.0 A1
2
1. Headlight bulb cover
1
U4P7E1E0.book Page 25 Wednesday, December 12, 2007 9:37 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-26
6
WARNING
EWA10790
Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooleddown.
5. Place a new headlight bulb into po-
sition, and then install the bulb
holder by turning the holder clock-
wise.CAUTION:
ECA10660
Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency ofthe glass, the luminosity of the bulb,
and the bulb life will be adversely af-
fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with al-
cohol or thinner.
6. Install the headlight bulb cover.
7. Install the cowling.
8. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAUT1260
Replacing a front turn signal
light bulb CAUTION:
ECA10670
It is advisable to have a Yamahadealer perform this job.
1. Place the scooter on the center-
stand.
2. Remove cowling A. (See page
6-6.)
3. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
4. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
1. Headlight bulb holder
2. Headlight bulb
1
2
1. Do not touch the glass part of the bulb.
1. Turn signal light bulb socket
1
U4P7E1E0.book Page 26 Wednesday, December 12, 2007 9:37 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
65. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
6. Install the socket (together with the
bulb) by turning it clockwise.
7. Install the cowling.
EAU37741
Rear turn signal light and
tail/brake light If a rear turn signal light or the tail/brake
light does not come on, have a Yamaha
dealer check its electrical circuit or re-
place the bulb.
EAU45460
Replacing the auxiliary light
bulb If the auxiliary light bulb burns out, re-
place it as follows.
1. Place the vehicle on the center-
stand.
2. Remove cowling A. (See page
6-6.)
3. Remove the auxiliary light socket
(together with the bulb) by pulling it
out.
4. Remove the defective bulb by pull-
ing it out.
5. Insert a new bulb into the socket.1. Auxiliary light bulb
2. Auxiliary light bulb socket
12
U4P7E1E0.book Page 27 Wednesday, December 12, 2007 9:37 AM