2008 YAMAHA TZR50 light

ITEM CHECKS PAGE
Control cables• Make sure that operation is smooth.
• Lubricate if necessary.6-23
• Check chain slack.
Drive chain• Adjust if necessary.
6-21, 6-22
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
Wheels and tires• Check tire condition and tread depth.
6-14, 6-16
• Check air pressure.
• Correct if necessary.
Brake and shift pedals• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.3-4, 3-5, 6-24
Brake and clutch levers• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.3-4, 3-5, 6-24
Sidestand• Make sure that operation is smooth.
• Lubricate pivot if necessary.3-10, 6-25
Chassis fasteners• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.—
Instruments, lights, signals • Check operation.
and switches• Correct if necessary.—
Engine stop switch• Check operation.3-3
Sidestand switch• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.3-10
4
PRE-OPERATION CHECKS
4-3
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 14

EAU15950
EWA10270
s s
WARNING
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer
regarding any control or func-
tion that you do not thoroughly
understand.
Never start the engine or ope-
rate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of cons-
ciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised comple-
tely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
EAU16050
Starting a cold engine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
The transmission is in the neutral
position.
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EWA10290
s s
WARNING
Before starting the engine,
check the function of the igni-
tion circuit cut-off system
according to the procedure
described on page 3-11.
Never ride with the sidestand
down.
1. Turn the fuel cock lever to “ON”.
2. Turn the key to “
f” and make
sure that the engine stop switch
is set to “
f”.
3. Shift the transmission into the
neutral position.
NOTE:
When the transmission is in the neu-
tral position, the neutral indicator lightshould be on, otherwise have a
Yamaha dealer check the electrical
circuit.
4. Turn the starter (choke) on and
completely close the throttle.
(See page 3-8.)
5. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the
engine more than 10 seconds on any
one attempt.
ECA11410
CAUTION:
The 2-stroke engine oil level war-
ning light should come on when the
start switch is pushed, and it
should go off when the start switch
is released. If the warning light flic-
kers or remains on after starting,
immediately stop the engine, and
then check the 2-stroke engine oil
level and the vehicle for oil leakage.
5
OPERATION AND IMPORTANT RIDING POINTS
5-1
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 1

If necessary, add 2-stroke engine
oil, and then check the warning
light again. If the warning light does
not come on when pushing the
start switch, or if it does not go off
after starting with sufficient 2-stro-
ke engine oil, have a Yamaha dealer
check the electrical circuit.
6. After starting the engine, move
the starter (choke) back halfway.
ECA11040
CAUTION:
For maximum engine life, never
accelerate hard when the engine is
cold!
7. When the engine is warm, turn
the starter (choke) off.
NOTE:
The engine is warm when it responds
normally to the throttle with the starter
(choke) turned off.
EAU16640
Starting a warm engine
Follow the same procedure as for
starting a cold engine with the excep-
tion that the starter (choke) is not
required when the engine is warm.
EAU16671
Shifting
1. Shift pedal
Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing
hills, etc.
The gear positions are shown in the
illustration.
NOTE:
To shift the transmission into the neu-
tral position, press the shift pedal
down repeatedly until it reaches the
end of its travel, and then slightly rai-
se it.
6
5
4
3
2
N
1
1
5
OPERATION AND IMPORTANT RIDING POINTS
5-2
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 2

ECA10260
CAUTION:
Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long
distances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.
Always use the clutch while
changing gears to avoid dama-
ging the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.
EAU16800
Tips for reducing fuel
consumption
Fuel consumption depends largely on
your riding style. Consider the follo-
wing tips to reduce fuel consumption:
Turn the starter (choke) off as
soon as possible.
Shift up swiftly, and avoid high
engine speeds during accelera-
tion.
Do not rev the engine while shif-
ting down, and avoid high engine
speeds with no load on the engi-
ne.
Turn the engine off instead of let-
ting it idle for an extended length
of time (e.g., in traffic jams, at
traffic lights or at railroad cros-
sings).
EAU16830
Engine break-in
There is never a more important
period in the life of your engine than
the period between 0 and 1000 km
(600 mi). For this reason, you should
read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themsel-
ves to the correct operating clearan-
ces. During this period, prolonged
full-throttle operation or any condition
that might result in engine overhea-
ting must be avoided.
EAU17130
0~500 km (0~300 mi)
Avoid prolonged operation above
4.000 r/min.
After every hour of operation, stop the
engine, and then let it cool for five to
ten minutes.
Vary the engine speed from time to
time. Do not operate the engine at
one set throttle position.
5
OPERATION AND IMPORTANT RIDING POINTS
5-3
5WX-F8199-E2.qxd 13/9/06 10:58 Página 3

ODOMETER READING (x 1000 Km)
ANNUAL
NO ITEM CHECK OR MAINTENANCE JOB
1 6 12 18 24CHECK
21Transmission oil• Check oil level.√√ √ √√ √
• Change.√√
22 *Front and rear brake
switches• Check operation.√√ √ √√ √
23Moving parts and cables• Lubricate.√√√√ √
Throttle grip housing• Check operation and free play.
24 * • Adjust the throttle cable free play if necessary.√√√√ √
and cable
• Lubricate the throttle grip housing and cable.
25 *Lights, signals and • Check operation.
switches• Adjust headlight beam.√√ √ √√ √
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
EAUM1890
NOTE:
Replace the air filter element more frequently if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 4

EAU19630
Checking the spark plug
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause
any spark plug to slowly erode, the
spark plug should be removed and
checked in accordance with the
periodic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
To remove the spark plug
1. Remove cowling C. (See page
6-5.)
1. Spark plug cap
2. Remove the spark plug cap.
1. Spark plug wrench
3. Remove the spark plug as
shown, with the spark plug
wrench included in the owner’s
tool kit.
To check the spark plug
1. Check that the porcelain insula-
tor around the center electrode of
the spark plug is a medium-to-
light tan (the ideal color when the
motorcycle is ridden normally).
NOTE:
If the spark plug shows a distinctly
different color, the engine could be
defective. Do not attempt to diagnose
such problems yourself. Instead, have
a Yamaha dealer check the motorcy-
cle.
2. Check the spark plug for electro-
de erosion and excessive carbon
or other deposits, and replace it if
necessary.
To install the spark plug
1. Measure the spark plug gap with
a wire thickness gauge and, if
necessary, adjust the gap to spe-
cification.
2. Clean the surface of the spark
plug gasket and its mating surfa-
ce, and then wipe off any grime
from the spark plug threads.
Spark plug gap:
0.6 ~ 0.7 mm (0.023 ~ 0.027 in)
Specified spark plug:
NGK BR9 ES
1
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 7

1. Spark plug wrench
3. Install the spark plug with the
spark plug wrench, and then
tighten it to the specified torque.
NOTE:
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4~1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
4. Install the spark plug cap.
5. Install the cowling.EAUM1270
Transmission oil
The transmission oil level should be
checked before each ride. In addition,
the oil must be changed at the inter-
vals specified in the periodic mainte-
nance and lubrication chart.
To check the transmission oil level
1. Place the vehicle on a level surface
and hold it in an upright position.
NOTE:
Make sure that the vehicle is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
1. Oil filler cap
2. Oil check bolt
3. Transmission oil drain bolt
3
2
1
Tightening torque:
Spark plug:
22.5 Nm (2.2 m•kgf, 16.3 ft•lbf)
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 8

NOTE:
The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level in the
coolant reservoir.
NOTE:
The coolant should be between the
minimum and maximum level marks.
3. If the coolant is at or below the
minimum level mark, open thereservoir cap, add coolant to the
maximum level mark, and then
close the reservoir cap.
EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
NOTE:
If the engine overheats, see page
6-33 for further instructions.
EAU20431
To change the coolant
1. Place the vehicle on the centers-
tand and let the engine cool if
necessary.
2. Remove cowlings A and B. (See
page 6-5.)
3. Place a container under the engi-
ne to collect the used coolant.
1. Radiator cap
2. Coolant drain bolt
4. Remove the radiator cap.EWA10380
s s
WARNING
Never attempt to remove the radia-
tor cap when the engine is hot.
5. Remove the coolant drain bolt to
drain the cooling system.
6. After the coolant is completely
drained, thoroughly flush the
cooling system with clean tap
water.
7. Install the coolant drain bolt, and
then tighten it to the specified
torque.
1
2
MAX
MIN
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
5WX-F8199-E2.qxd 29/05/2006 14:23 Página 10