2008 YAMAHA MAJESTY 125 oil type

EAUM1260
Engine oil
The engine oil level should be chec-
ked before each ride. In addition, the
oil must be changed at the intervals
specified in the periodic maintenance
and lubrication chart
and when the oil change indicator
display comes on.
To check the engine oil level
1. Place the scooter on the centers-
tand.
NOTE:
Make sure that the scooter is positio-
ned straight up when checking the oil
level. A slight tilt to the side can result
in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
1. Engine oil filler cap
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, insert it
back into the oil filler hole (wit-
hout screwing it in), and then
remove it again to check the oil
level.
1. Engine oil filler cap
2. Dipstick
3. Maximum level mark
4. Minimum level mark
NOTE:
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to rai-
se it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
To change the engine oil
1. Start the engine, warm it up for
several minutes, and then turn it
off.
1
2
3
4
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
5D8-F819D-E0.qxd 1/6/07 17:30 Página 44

EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
1. Do not touch the glass part of the bulb
5. Place a new headlight bulb into
position, and then secure it with
the bulb holder.
ECA10650
CAUTION:
Take care not to damage the follo-
wing parts:
Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it
free from oil, otherwise thetransparency of the glass, the
luminosity of the bulb, and the
bulb life will be adversely affec-
ted. Thoroughly clean off any
dirt and fingerprints on the
headlight bulb using a cloth
moistened with alcohol or thin-
ner.
Headlight lens
• Do not affix any type of tinted
film or stickers to the head-
light lens.
• Do not use a headlight bulb
of a wattage higher than spe-
cified.
6. Connect the headlight coupler.
7. Install the headlight bulb cover.
8. Install the panel.
9. Have a Yamaha dealer adjust the
headlight beam if necessary.
To replace the high beam
headlight bulb
1. Remove panel A. (See page 6-6.)
1. Headlight bulb cover
2. Remove the bulb cover.
1. Headlight bulb holder
3. Unhook the headlight bulb holder
by turning it counterclockwise,
and then remove the defective
bulb
1
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-28
5D8-F819D-E0.qxd 1/6/07 17:30 Página 63

EWA10790
s s
WARNING
Headlight bulbs get very hot. The-
refore, keep flammable products
away from a lit headlight bulb, and
do not touch the bulb until it has
cooled down.
4. Place a new headlight bulb into
position, and then secure it with
the bulb holder by turning it
clockwise
ECA10650
CAUTION:
Take care not to damage the follo-
wing parts:
Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it
free from oil, otherwise the
transparency of the glass, the
luminosity of the bulb, and the
bulb life will be adversely affec-
ted. Thoroughly clean off any
dirt and fingerprints on the
headlight bulb using a cloth
moistened with alcohol or thin-
ner.
Headlight lens• Do not affix any type of tinted
film or stickers to the head-
light lens.
• Do not use a headlight bulb
of a wattage higher than spe-
cified.
5. Install the headlight bulb cover
6. Install the panel.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24250
Replacing a front turn signal
light bulb
1. Screw
2. Front turn signal light lens
3. Light bulb
1. Remove the front turn signal light
lens by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.
ECA11190
CAUTION:
Do not overtighten the screw,
otherwise the lens may break.
1 2
3
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-29
5D8-F819D-E0.qxd 1/6/07 17:30 Página 64

DimensionsOverall length
2030 mm (79.9 in)
Overall width
745 mm (29.3 in)
Overall height
1285 mm (50.6 in)
Seat height
774 mm (30.5 in)
Wheelbase
1480 mm (58.2 in)
Ground clearance
102 mm (4.01 in)
Minimum turning radius
3840 mm (151.2 in)
WeightWith oil and fuel
148 kg (326 lb)
EngineEngine type
Liquid cooled 4-stroke, SOHC
Cylinder arrangement
Forward-inclined single cylinder
Displacement
124.1 cm
3(7.57 cu.in)
Bore x stroke
53.7 x 54.8 mm (2.11 x 2.15 in)
Compression ratio
11:1
Starting system
Electric starter
Lubrication system
Wet sump
Engine oilType
SAE10W30 or SAE10W40
Recommended engine oil grade
API service SE, SF, SG type or higher
Engine oil quantityPeriodic oil change
1.2 L (1.27 US qt) (1.06 Imp.qt)
Final transmission oilType
YAMALUBE 4 (10W30) of SAE10W30
type SE motorolie
Quantity
0.15 L (0.16 US qt) (0.88 Imp.qt)
Cooling systemRadiator capacity (including all routes)
1.20 L (1.27 US qt) (1.06 Imp.qt)
Coolant reservoir capacity (up to the maxi-
mum level mark)
0.30 L (0.32 US qt) (0.26 Imp.qt)
Air filterAir filter element
Dry element
Recommended fuelRecommended fuel
Unleaded fuel
Fuel tank capacity
10.5 L ( 2.77US gal) (2.31 Imp.gal)
Fuel reserve amount
3 L (0.79 US gal) (0.66 Imp gal)
CarburetorManufacturer
TEIKEI
Type x quantity
TK28 x 1
Spark plug (s)Manufacturer/model
NGK / CR8E
Spark plug gap
0.7 - 0.8 (0.028 - 0.031 in)
ClutchClutch type
Dry, automatic centrifugal
TransmissionPrimary reduction system
Helical gear
Primary reduction ratio
40/15 (2.666)
Secondary reduction system
Helical gear
Secondary reduction ratio
40/15 (2.666)
Transmission type
V-belt automatic
8
SPECIFICATIONS
8-1
5D8-F819D-E0.qxd 1/6/07 17:31 Página 73

Operation
Centrifugal automatic type
ChassisFrame type
Steel tube underbone
Caster angle
28 º
Trail
104.0 mm (4.09 in)
Front tireType
Tubeless
Size
120/70 - 12 51L
Manufacturer/model
CONTINENTAL / ZIPPY 1
PIRELLI / SL26
MICHELIN / BOPPER
Rear tireType
Tubeless
Size
130/70 - 12 56L
Manufacturer/model
CONTINENTAL / ZIPPY 1
PIRELLI / SL26
MICHELIN / BOPPER
LoadingMaximum load
177 kg (390.29 lb)
Load is total weight of the equipement, dri-
ver, passenger and accessories
Tire air pressure (measured on cold
tires)
Loading condition
0–90 kg (0–198 lb)
Front
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear
220 kPa (31 psi) (2.2 kgf/cm
2)
Loading condition
90 kg (198 lb)–Maximum load
Front
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear
240 kPa (34 psi) (2.4 kgf/cm
2)
Front wheelWheel type
Aluminium wheel
Rim size
12 x MT3.50
Rear wheelWheel type
Aluminium wheel
Rim size
12 x MT3.50
Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 4
Rear brakeType
Single disc brakeOperation
Left hand operation
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm (3.54 in)
Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm (3.54 in)
Electrical systemIgnition system
CDI
Charging system
AC magneto
BatteryManufacturer/model
GS / CB7L-B2
Voltage, capacity
12 V, 8.0 Ah
Bulb voltage, wattage x quantityHeadlight
12 V, 55.0 W x 2
Auxiliary light
12 V, 5.0 W x 2
Tail/brake light
8
SPECIFICATIONS
8-2
5D8-F819D-E0.qxd 1/6/07 17:31 Página 74