2008 YAMAHA MAJESTY 125 ABS

INTRODUCTION
IMPORTANT MANUAL INFORMATION
TABLE OF CONTENTS
SAFETY INFORMATION.....................1-1
Further safe-riding points .................1-4
DESCRIPTION.....................................2-1
Left view ...........................................2-1
Right view .........................................2-2
Controls and instruments .................2-3
INSTRUMENT AND CONTROL
FUNCTIONS........................................3-1
Main switch/steering lock .................3-1
Indicator lights ..................................3-2
Speedometer unit .............................3-2
Battery voltage/fuel gauge ...............3-3
Clock .................................................3-4
Anti-theft alarm (optional) .................3-5
Handlebar switches ..........................3-5
Front brake lever...............................3-6
Rear brake lever................................3-6
Fuel tank cap ....................................3-7
Fuel ...................................................3-8
Fuel tank breather/overflow hose .....3-9
Catalytic converter............................3-9
Seat...................................................3-9
Front storage compartment............3-10Storage compartment.....................3-11
Adjusting the shock absorber
assemblies...................................3-12
Sidestand ........................................3-12
Ignition circuit cut-off system .........3-13
PRE-OPERATION CHECKS...............4-1
Pre-operation check list....................4-2
OPERATION AND IMPORTANT RIDING
POINTS................................................5-1
Starting a cold engine ......................5-1
Starting off ........................................5-2
Acceleration and deceleration ..........5-2
Braking..............................................5-2
Tips for reducing fuel consumption..5-3
Engine break-in.................................5-3
Parking ..............................................5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR...................................6-1
Owner’s tool kit .................................6-1
Periodic maintenance and
lubrication chart ............................6-3
Removing and installing panels........6-6
Checking the spark plug ..................6-7
Engine oil ..........................................6-9
Final transmission oil ......................6-11
Coolant ...........................................6-12
Air filter and V-belt case air filter
elements ......................................6-14Adjusting the carburetor .................6-15
Adjusting the throttle cable free
play ..............................................6-15
Valve clearance ...............................6-16
Tires ................................................6-16
Cast wheels ....................................6-18
Front and rear brake lever free
play ..............................................6-19
Checking the front and rear brake
pads.............................................6-19
Checking the brake fluid level ........6-20
Changing the brake fluid ................6-21
Checking and lubricating
the cables ....................................6-21
Lubricating the front and rear brake
levers ...........................................6-22
Checking and lubricating the
centerstand and sidestand .........6-22
Checking the front fork ...................6-23
Checking the steering.....................6-23
Checking the wheel bearings .........6-24
Battery ............................................6-24
Replacing the fuses ........................6-26
Replacing a headlight bulb .............6-27
Replacing a front turn signal
light bulb......................................6-29
Replacing the tail/brake light bulb
or a rear turn signal light bulb .....6-30
Replacing the license plate light
bulb .............................................6-31
Replacing the auxiliary light bulb ...6-31
TABLE OF CONTENTS
5D8-F819D-E0.qxd 1/6/07 17:30 Página 6

EAU14880
Adjusting the shock
absorber assemblies
1. Spring preload adjusting ring
2. Position indicator
Each shock absorber assembly is
equipped with a spring preload adjus-
ting ring.
ECA10100
CAUTION:
Never attempt to turn an adjusting
mechanism beyond the maximum
or minimum settings.
EWA10210
s s
WARNING
Always adjust both shock absorber
assemblies equally, otherwise poor
handling and loss of stability may
result.
Adjust the spring preload as follows.
To increase the spring preload and
thereby harden the suspension, turn
the adjusting ring on each shock
absorber assembly in direction (a). To
decrease the spring preload and the-
reby soften the suspension, turn the
adjusting ring on each shock absor-
ber assembly in direction (b).
NOTE:
Align the appropriate notch in the
adjusting ring with the position indica-
tor on the shock absorber.
EAU15301
Sidestand
1. Sidestand switch
2. Sidestand
The sidestand is located on the left
side of the frame. Raise the sidestand
or lower it with your foot while holding
the motorcycle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain
situations. (See further down for an
explanation of the ignition circuit cut-
off system.)
1
2
Spring preload setting:
Minimum (soft):
1
Standard:
2
Maximum (hard):
4
2 1
ba3
INSTRUMENT AND CONTROL FUNCTIONS
3-12
5D8-F819D-E0.qxd 1/6/07 17:30 Página 26

ODOMETER READING (x 1000 Km)
ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB
1 6 12 18 24CHECK
8*Rear brake• Check operation, fluid level and vehicle for fluid leakage.√√ √ √√ √• Replace brake pads. Whenever worn to the limit
9*Brake hoses• Check for cracks or damage.√√√√ √• Replace. Every 4 years
10 *Wheels• Check runout and for damage.√√√√
• Check tread depth and for damage.
11 *Tires• Replace if necessary.
√√√√ √
• Check air pressure.
• Correct if necessary.
12 *Wheel bearings• Check bearing for looseness or damage.√√√√
13 *Steering bearings• Check bearing play and steering for roughness.√√ √ √√• Lubricate with lithium-soap-based grease. Every 20000 km
14 *Chassis fasteners• Make sure that all nuts, bolts and screws are properly
tightened.√√√√ √
15Sidestand, centerstand• Check operation.
• Lubricate.√√√√ √
16 *Sidestand switch• Check operation.√√ √ √√ √
17 *Front fork• Check operation and for oil leakage.√√√√
18 *Shock absorber
• Check operation and shock absorbers for oil leakage.√√√√
assemblies
19 *Carburetor• Adjust engine idling speed.√√ √ √√ √
• Change. (See page 6-9.)√When the oil change indicator light
20Engine oilcomes on (every 3000 km)
• Check oil level and vehicle for oil leakage. Every 3000 km√
21 *Engine oil strainer• Clean.√√√
6
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
5D8-F819D-E0.qxd 1/6/07 17:30 Página 39

thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
NOTE:
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA10790
CAUTION:
Do not use warm water since it
increases the corrosive action of
the salt.
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal clea-
ner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
7
SCOOTER CARE AND STORAGE
7-2
5D8-F819D-E0.qxd 1/6/07 17:30 Página 70

Operation
Centrifugal automatic type
ChassisFrame type
Steel tube underbone
Caster angle
28 º
Trail
104.0 mm (4.09 in)
Front tireType
Tubeless
Size
120/70 - 12 51L
Manufacturer/model
CONTINENTAL / ZIPPY 1
PIRELLI / SL26
MICHELIN / BOPPER
Rear tireType
Tubeless
Size
130/70 - 12 56L
Manufacturer/model
CONTINENTAL / ZIPPY 1
PIRELLI / SL26
MICHELIN / BOPPER
LoadingMaximum load
177 kg (390.29 lb)
Load is total weight of the equipement, dri-
ver, passenger and accessories
Tire air pressure (measured on cold
tires)
Loading condition
0–90 kg (0–198 lb)
Front
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear
220 kPa (31 psi) (2.2 kgf/cm
2)
Loading condition
90 kg (198 lb)–Maximum load
Front
190 kPa (27 psi) (1.9 kgf/cm
2)
Rear
240 kPa (34 psi) (2.4 kgf/cm
2)
Front wheelWheel type
Aluminium wheel
Rim size
12 x MT3.50
Rear wheelWheel type
Aluminium wheel
Rim size
12 x MT3.50
Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 4
Rear brakeType
Single disc brakeOperation
Left hand operation
Recommended fluid
DOT 4
Front suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm (3.54 in)
Rear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90 mm (3.54 in)
Electrical systemIgnition system
CDI
Charging system
AC magneto
BatteryManufacturer/model
GS / CB7L-B2
Voltage, capacity
12 V, 8.0 Ah
Bulb voltage, wattage x quantityHeadlight
12 V, 55.0 W x 2
Auxiliary light
12 V, 5.0 W x 2
Tail/brake light
8
SPECIFICATIONS
8-2
5D8-F819D-E0.qxd 1/6/07 17:31 Página 74

AAcceleration and deceleration ...................5-2
Air filter and V-belt case air filter
elements ................................................6-14
Anti-theft alarm (optional) ..........................3-5
Auxiliary light bulb, replacing ...................6-31
BBattery......................................................6-24
Brake fluid level, checking .......................6-20
Brake fluid, changing ...............................6-21
Brake lever, front ........................................3-6
Brake lever, rear .........................................3-6
Brake levers, lubricating ..........................6-22
Braking .......................................................5-2
CCables, checking and lubricating ............6-21
Carburetor,adjusting.................................6-15
Care............................................................7-1
Catalytic converter .....................................3-9
Caution, matte color ..................................7-1
Centerstand and sidestand, checking
and lubricating .......................................6-22
Clock ..........................................................3-4
Coolant.....................................................6-12
Coolant temperature warning light ............3-2
DDimmer switch ...........................................3-5
EEngine break-in ..........................................5-3
Engine oil ...................................................6-9
FFinal transmission oil ...............................6-11
Front and rear brake lever free play.........6-19
Front and rear brake pads, checking ......6-19Front fork, checking .................................6-23
Front Storage compartment ....................3-10
Fuel ............................................................3-8
Fuel consumption, tips for reducing ..........5-3
Fuel tank breather/overflow hose ..............3-9
Fuel tank cap .............................................3-7
Fuses, replacing .......................................6-26
HHandlebar switches ...................................3-5
Hazard switch ............................................3-6
Headlight bulb, replacing .........................6-27
High beam indicator light...........................3-2
Horn switch ................................................3-5
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-13
Indicator lights ...........................................3-2
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-31
MMain switch/steering lock ..........................3-1
Model label ................................................9-2
OOil change indicator ...................................3-2
PPanels, removing and installing .................6-6
Parking .......................................................5-4
Part locations .............................................2-1
Periodic maintenance and lubrication
chart .........................................................6-3
Pre-operation check list .............................4-2
SSafe-riding points.......................................1-4
Safety information ......................................1-1
Seat ............................................................3-9
Shock absorber assemblies, adjusting....3-12
Sidestand .................................................3-12
Spark plug, checking .................................6-7
Specifications.............................................8-1
Speedometer unit ......................................3-2
Start switch ................................................3-5
Starting a cold engine ................................5-1
Starting off .................................................5-2
Steering, checking ...................................6-23
Storage.......................................................7-3
Storage compartment ..............................3-11
TTail/brake light bulb or rear turn signal
light bulb, replacing ...............................6-30
Throttle cable free play, adjusting ............6-15
Tires .........................................................6-16
Tool kit ........................................................6-1
Troubleshooting .......................................6-31
Troubleshooting charts ............................6-32
Turn signal indicator lights .........................3-2
Turn signal light bulb (front), replacing ....6-29
Turn signal switch ......................................3-5
VValve clearance ........................................6-16
Vehicle identification number .....................9-1
WWheel bearings, checking........................6-24
Wheels .....................................................6-18
INDEX
5D8-F819D-E0.qxd 1/6/07 17:31 Página 78