2008 YAMAHA JOG50R ECO mode

EAUS1420
Multi-function display
1. Button
2. Odometer/Tripmeter
3. Digital clock
4. Fuel meter
EWA12311
s s
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display.
The multi-function display is equip-
ped with the following:
●a digital clock
●an odometer (which shows the
total distance traveled)
●a tripmeter (which shows the dis-
tance traveled since it was last
set to zero)
●a fuel gauge
●a self-diagnosis device
●a function button (which selects
and resets various modes of the
multi-function display)
NOTE:
●Be sure to turn the key to “f”
before using the button.
●For the U.K. only: The odometer
and tripmeter are displayed in
miles.
To set the clock:
1. Select the odometer and push
the button for at least two
seconds.
2. When the hour digits start flas-
hing, push the button to set the
hours.3. To change the tens digit, push
the button for at least seconds.
4. When the tens digit starts flas-
hing, push the button to set the
tens digit.
5. To change the unit digit, push the
button for at least two seconds.
6. When the unit digit starts flas-
hing, push the button to set the
minutes.
km/h
01020304050607080
12
3
4
INSTRUMENT AND CONTROL FUNCTIONS
3-4
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 20

7. Push the button for at least two
seconds to start the clock.
NOTE:
After setting the clock, be sure to
push the button for at least two
seconds before turning the key to
“e”, otherwise the clock will not be
set.
Odometer and tripmeter modes
Pushing the button switches the dis-
play between the odometer mode
“ODO” and the tripmeter “TRIP” in
the following order:
ODO
TRIP ODO
1. Odometer
2. Tripmeter
To reset the tripmeter, select it by
pushing the button, and then push it
again for at least two seconds.
Fuel gauge
The fuel gauge indicates the amount
of fuel in the fuel tank. The display
segments of the fuel gauge disappear
towards “E” (Empty) as the fuel level
decreases. When only one segment is
left near “E”, refuel as soon as possi-
ble.
Self-diagnosis device
This model is equipped with a self-
diagnosis device for the fuel electrical
circuit.If the fuel electrical circuit is defective,
all LCD segments of the fuel gauge
will flash. If this occurs, have a Yama-
ha dealer check the vehicle.
PRESS
BUTTON
PRESS
BUTTON
INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 21

EAU13211
Fuel
1. Fuel tank filler tube
2. Fuel level
Make sure that there is sufficient fuel
in the tank. Fill the fuel tank to the
bottom of the filler tube as shown.
EWA10880
s s
WARNING
●Do not overfill the fuel tank,
otherwise it may overflow
when the fuel warms up and
expands.
●Avoid spilling fuel on the hot
engine.
ECA10070
CAUTION:
Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted surfa-
ces or plastic parts.
EAU13270
Your Yamaha engine has been desig-
ned to use regular unleaded gasoline
with a research octane number of 91
or higher. If knocking (or pinging)
occurs, use a gasoline of a different
brand or premium unleaded fuel. Use
of unleaded fuel will extend spark
plug life and reduce maintenance
costs.
EAU13431
Catalytic converter
This model is equipped with a cataly-
tic converter in the exhaust system.
EWA10860
s s
WARNING
The exhaust system is hot after
operation. Make sure that the
exhaust system has cooled down
before doing any maintenance
work.
ECA10700
CAUTION:
The following precautions must be
observed to prevent a fire hazard or
other damages.
●Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.
●Never park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
●Do not allow the engine to idle
too long.
Recommended fuel:
REGULAR UNLEADED GASOLINE
ONLY
Fuel tank capacity:
5.5 L (1.45 US gal) (1.21 Imp.gal)
Fuel reserve amount:
1.9 L (0.50 US gal) (0.42 Imp.gal)
1
2
ZAUM0020
INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
5RW-F8199-E4.QXD 19/11/07 08:01 Página 24

EWA11310
s s
WARNING
●Make sure that no foreign
material enters the final trans-
mission case.
●Make sure that no oil gets on
the tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
EAUS1200
Coolant (only for liquid-
cooled models)
The coolant level should be checked
before each ride. In addition, the coo-
lant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAUM2101
To check the coolant level
1. Place the vehicle on a level surfa-
ce and hold it in an upright posi-
tion.
NOTE:
●The coolant level must be chec-
ked on a cold engine since the
level varies with engine tempera-
ture.
●Make sure that the vehicle is
positioned straight up when
checking the coolant level. A
slight tilt to the side can result in
a false reading.
2. Check the coolant level through
the check window.
NOTE:
The coolant should be between the
minimum and maximum level marks.
1. Coolant level window
2. Maximum level mark
3. Minimum level mark
3. If the coolant is at or below the
minimum level mark, remove the
cowling A. (See page 6-5.)
4. Open the reservoir cap, and then
add coolant to the maximum
level mark.
Coolant reservoir capacity:
0.25 L (0.26 US qt) (0.22 Imp.qt)
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.11 L (0.12 US qt) (0.10 Imp.qt)
PERIODIC MAINTENANCE AND MINOR REPAIR
6-8
6
5RW-F8199-E4.QXD 19/11/07 08:01 Página 43

To store the battery
1. If the model will not be used for
more than one month, remove
the battery, fully charge it, and
then place it in a cool, dry place.
2. If the battery will be stored for
more than two months, check it
at least once a month and fully
charge it if necessary.
3. Fully charge the battery before
installation.
4. After installation, make sure that
the battery leads are properly con-
nected to the battery terminals.
ECA10630
CAUTION:
●Always keep the battery char-
ged. Storing a discharged bat-
tery can cause permanent bat-
tery damage.
●To charge a sealed-type (MF)
battery, a special (constant-
voltage) battery charger is
required. Using a conventional
battery charger will damage
the battery. If you do not have
access to a sealed-type (MF)
battery charger, have a Yamaha
dealer charge your battery.
EAUS1180
Replacing the fuse
The fuse holder is located beside the
battery case.
If the fuse is blown, replace it as
follows.
1. Turn the key to “e” and turn off
all electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
1. Main fuse
ECA10640
CAUTION:
Do not use a fuse of a higher ampe-
rage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “f” and turn on
the electrical circuits to check if
the devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
Specified fuse:
7.5 A
PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
6
5RW-F8199-E4.QXD 19/11/07 08:01 Página 55

Dimensions:Overall length:
1740 mm (68.5 in)
Overall width:
675 mm (26.6 in)
Overall height:
1065 mm (41.9 in)
Seat height:
770 mm (30.3 in)
Wheelbase:
1210 mm (47.6 in)
Ground clearance:
132 mm (5.19 in)
Weight:With oil and fuel:
CS50/CS50M: 81.0 kg (178.6 lb)
CS50Z: 84.0 kg (185.2 lb)
Engine:Engine type:
CS50/CS50M: Air cooled 2-stroke
CS50Z: Liquid cooled 2-stroke
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
49.0 cm
3(2.99 cu.in)
Bore x stroke:
40.0 x 39.2 mm (1.57 x 1.54 in)
Compression ratio:
CS50: 11.60:1
CS50M: 10,10 :1
CS50Z: 11.40 :1
Starting system:
Electric starter and kickstarterLubrication system:
Separate lubrication (Yamaha autolube)
Engine oil:Type:
YAMALUBE 2-cycle oil or 2-stroke engine
oil (JASO FC grade) or (ISO EG-C or EG-
D grade)
Engine oil quantity:
Quantity:
1.4 L (1.48 US qt) (1.23 Imp.qt)
Final transmission oil:Type:
SAE10W30 type SE motor oil
Quantity:
0.11 L (0.12 US qt) (0.10 Imp.qt)
CS50Z: Cooling system:Coolant reservoir capacity (up to the maxi-
mum level mark):
0.25 L (0.26 US qt) (0.22 Imp.qt)
Radiator capacity (including all routes):
0.91 L (0.96 US qt) (0.80 Imp.qt)
Air filter:Air filter element:
Wet element
Fuel:Recommended fuel:
Regular unleaded gasoline only
Fuel tank capacity:
5.5 L (1.45 US gal) (1.21 Imp.gal)
Fuel reserve amount
1.9 L (0.50 US gal) (0.42 Imp.gal)
Carburetor:Manufacturer:
GURTNERType x quantity:
PY 12 x 1
Spark plug(s):Manufacturer/model:
CS50-CS50Z: NGK/BR8HS
CS50M: NGK/BPR4HS
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:Clutch type:
Dry, centrifugal automatic
Final transmission oil:Primary reduction system:
Helical gear
Primary reduction ratio:
52 x 13 (4.000)
Secondary reduction system:
Spur gear
Secondary reduction ratio:
CS50: 42 x 13 (3.231)
CS50M: 45 x 12(3.750)
CS50Z: 43 x 13 (3.308)
Transmission type:
V-belt automatic
Operation:
Centrifugal automatic type
Chassis:Frame type:
Steel tube underbone
Caster angle:
25.00 °
Trail:
80.0 mm (3.15 in)
SPECIFICATIONS
8-1
8
5RW-F8199-E4.QXD 19/11/07 08:01 Página 66

Front tire:Type:Tubeless
Size: 110/70-12 47L
Manufacturer/model: CHENG SHIN TIRE / C922
Rear tire:Type:Tubeless
Size: 120/70-12 51L
Manufacturer/model: CHENG SHIN TIRE / C922
Loading:Maximum load:CS50/CS50M: 169 kg (372 lb)
CS50Z: 166 kg (366 lb)
(Total weight of rider, passenger, cargo and
accessories)
Tire air pressure (measured on cold
tires):
Loading condition: 0–90 kg (0–198 lb)
Front: 175 kPa (25 psi) (1.75 kgf/cm
2)
Rear: 200 kPa (28 psi) (2.00 kgf/cm
2)
Loading condition:
CS50/CS50M 90~169 kg (198~373 lb)
CS50Z 90~166 kg (198~366 lb): Front:175 kPa (25 psi) (1.75 kgf/cm
2) Rear:
225 kPa (32 psi) (2.25 kgf/cm
2)
Front wheel:Wheel type: Cast wheel
Rim size: 12xMT2.75
Rear wheel:Wheel type:Cast wheel
Rim size: 12xMT3.00
Front brake:Type:Single disc brake
Operation: Right hand operation
Recommended fluid: DOT 4
Rear brake:Type:Drum brake
Operation: Left hand operation
Front suspension:Type:Telescopic fork
Spring/shock absorber type: Coil spring/oil damper
Wheel travel: 70.0 mm (2.76 in)
Rear suspension:Type:Unit swing Spring/shock absorber type:
Coil spring/oil damper
Wheel travel: 60.0 mm (2.36 in)
Electrical system:Ignition system:DC. CDI
Charging system: AC magneto
Battery:Model:GT4L-BS
Voltage, capacity: 12 V, 4.0 Ah
Headlight:
Bulb type:Incandescence
Bulb voltage, wattage x quantity:Headlight:12 V, 35.0 W/35.0 W x 1
Tail/brake light: 12 V, 21.0 W/5.0 W x 1
Front turn signal light: 12 V, 10.0 W x 2
Rear turn signal light: 12 V, 10.0 W x 2
Meter lighting: 12 V, 1.2 W x 2
High beam indicator light: 12 V, 1.2 W x 1
Oil level warning light: LED x 1
Turn signal indicator light: 12 V, 1.2 W x 2
SPECIFICATIONS
8-2
8
5RW-F8199-E4.QXD 21/11/07 11:37 Página 67

EAU26351
Identification numbers
Record the key identification number,
vehicle identification number and
model label information in the spaces
provided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the
vehicle is stolen.
KEY IDENTIFICATION NUMBER:
VEHICLE IDENTIFICATION NUMBER:
MODEL LABEL INFORMATION:
EAU26381
Key identification number
1. Key identification number
The key identification number is
stamped into the key tag.Record this
number in the space provided and
use it for reference when ordering a
new key.
EAU26410
Vehicle identification number
1. Vehicle identification number
The vehicle identification number is
stamped into the frame.
NOTE:
The vehicle identification number is
used to identify your vehicle and may
be used to register your vehicle with
the licensing authority in your area.
1
ZAUM0070
CONSUMER INFORMATION
9-1
9
5RW-F8199-E4.QXD 19/11/07 08:01 Página 69