2008 YAMAHA GRIZZLY 660 lock

8-52
83. Remove the headlight bulb holder by pushing
it in and turning it counterclockwise.
4. Remove the defective bulb by pulling it out.
WARNING
EWB02220A headlight bulb is hot when it is on and imme-
diately after it is turned off. Wait for the bulb to
cool before touching or removing it. You can
be burned or a fire could start if the bulb touch-es something flammable.
5. Insert a new headlight bulb into the bulb hold-
er by pushing it in.
CAUTION:ECB00650Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of the
bulb, and the bulb life will be adversely affect-
ed. Thoroughly clean off any dirt and finger-
prints on the headlight bulb using a clothmoistened with alcohol or thinner.
6. Install the bulb holder by pushing it in and turn-
ing it clockwise.
7. Install the bulb holder cover and the cover at
the rear of the headlight.
1. Headlight bulb holder
1. Do not touch the glass part of the bulb.
U23D60E0.book Page 52 Thursday, March 15, 2007 7:59 PM

8-53
8
CAUTION:ECB00670Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seatedproperly.
8. Adjust the headlight beam if necessary.EBU25550Adjusting a headlight beam CAUTION:ECB00690It is advisable to have a Yamaha dealer makethis adjustment.
To raise a headlight beam, turn the adjusting
screw in direction (a).
To lower a headlight beam, turn the adjusting
screw in direction (b).
EBU25640Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove panel G. (See page 8-9.)
2. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.1. Headlight beam adjusting screw
U23D60E0.book Page 53 Thursday, March 15, 2007 7:59 PM

8-54
83. Remove the defective bulb by pushing it in
and turning it counterclockwise.
4. Insert a new bulb into the bulb holder, push it
in, and then turn it clockwise until it stops.
5. Install the bulb holder (together with the bulb)
by turning it clockwise.
6. Install the panel.
EBU25650Removing a wheel 1. Loosen the wheel nuts.2. Elevate the ATV and place a suitable stand
under the frame.
3. Remove the nuts from the wheel.
4. Remove the wheel.
EBU25700Installing a wheel 1. Install the wheel and the nuts.NOTE:
The arrow mark on the tire must point toward
the rotating direction of the wheel.
1. Tail/brake light bulb holder
1. Wheel nut
U23D60E0.book Page 54 Thursday, March 15, 2007 7:59 PM

9-1
9
EBU25860
CLEANING AND STORAGE
EBU25880Cleaning Frequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.
1. Before cleaning the ATV:
a. Block off the end of the exhaust pipe to
prevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps
are properly installed.
2. If the engine case is excessively greasy, apply
degreaser with a paint brush. Do not apply de-
greaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden
hose. Use only enough pressure to do the job.CAUTION:ECB00710Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical de-
vices. Many expensive repair bills have result-ed from improper high-pressure detergent
applications such as those available in coin-
operated car washers.
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or bot-
tle brush is handy for hard-to-reach places.
5. Rinse the ATV off immediately with clean wa-
ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner
to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all
painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
U23D60E0.book Page 1 Thursday, March 15, 2007 7:59 PM

9-3
9 c. Install the spark plug cap onto the spark
plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with the
starter. (This will coat the cylinder wall with
oil.)
e. Remove the spark plug cap from the spark
plug, and then install the spark plug and
the spark plug cap.
6. Lubricate all control cables and the pivoting
points of all levers and pedals.
7. Check and, if necessary, correct the tire air
pressure, and then block up the ATV so that
all of its wheels are off the ground. Alternative-
ly, turn the wheels a little every month in order
to prevent the tires from becoming degraded
in one spot.
8. Cover the muffler outlet with a plastic bag to
prevent moisture from entering it.
9. Remove the battery and fully charge it. Store
it in a cool, dry place and charge it once a
month. Do not store the battery in an exces-
sively cold or warm place [less than 0 °C (30°F) or more than 30 °C (90 °F)]. For more in-
formation on storing the battery, see page
8-48.
NOTE:Make any necessary repairs before storing theATV.
U23D60E0.book Page 3 Thursday, March 15, 2007 7:59 PM

10-5
10
Coolant temperature warning light:
LED
Park indicator light:
LED
On-Command four-wheel-drive/differential gear lock
indicator:
LCD
High-range indicator light:
LED
Low-range indicator light:
LED
Differential gear lock indicator light:
LEDFuses:Main fuse:
30.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
10.0 A
Auxiliary DC jack fuse:
10.0 A
Backup fuse:
10.0 A
Four-wheel-drive motor fuse:
3.0 A
U23D60E0.book Page 5 Thursday, March 15, 2007 7:59 PM

INDEX
AAccessories and loading ................................................ 6-6
Accessories, auxiliary jack ........................................... 4-21
Air filter element, cleaning ............................................ 8-30
Axle boots .................................................................... 8-44BBattery .......................................................................... 8-48
Brake fluid, changing .................................................... 8-41
Brake fluid level, checking ............................................ 8-39
Brake lever free play and brake pedal position (rear),
adjusting and checking .............................................. 8-42
Brake lever free play, checking the front ...................... 8-41
Brake lever, front .......................................................... 4-12
Brake levers, checking and lubricating ......................... 8-45
Brake light switches ..................................................... 8-44
Brake pads, checking the front and rear ...................... 8-38
Brake pedal and rear brake lever ................................. 4-13
Brake pedal, checking and lubricating ......................... 8-46
Brakes, front and rear .................................................... 5-4CCables, checking and lubricating ................................. 8-45
Carburetor, adjusting .................................................... 8-36
Carrier, front ................................................................. 4-20
Carrier, rear .................................................................. 4-20
Chassis fasteners ........................................................... 5-7
Cleaning ......................................................................... 9-1
Coolant .................................................................. 5-3, 8-26
Coolant temperature warning light ................................. 4-2
DDifferential gear lock indicator light ................................ 4-3
Differential gear oil ................................................ 5-3, 8-24
Drive select lever .......................................................... 4-14
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ......... 8-38EEngine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-36
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-18
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-6FFinal gear oil .......................................................... 5-3, 8-22
Four-wheel-drive/differential gear lock indicator ............ 4-3
Fuel ....................................................................... 4-15, 5-3
Fuel cock ...................................................................... 4-16
Fuel tank cap ................................................................ 4-14
Fuses, replacing ........................................................... 8-50HHandlebar switches ........................................................ 4-6
Headlight beam, adjusting ............................................ 8-53
Headlight bulb, replacing .............................................. 8-51
High-range indicator light ............................................... 4-3
Horn switch .................................................................... 4-6
U23D60E0.book Page 1 Thursday, March 15, 2007 7:59 PM

IIdentification numbers .................................................. 11-1
Indicator lights and warning light .................................... 4-2
Instruments, lights and switches .................................... 5-7KKey identification number ............................................. 11-1LLabel locations ............................................................... 2-1
Light switch .................................................................... 4-6
Low-range indicator light ................................................ 4-3MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................. 8-5
Maintenance chart, emission control system ................. 8-3
Model label ................................................................... 11-2
Multifunction display ....................................................... 4-4NNeutral indicator light ..................................................... 4-2OOn-Command differential gear lock switch .................... 4-9
On-Command four-wheel-drive switch ........................... 4-8
Override switch .............................................................. 4-7
Owner’s manual and tool kit ........................................... 8-1PPanels, removing and installing ..................................... 8-9
Park indicator light ......................................................... 4-3
Parking ........................................................................... 6-6
Parking on a slope ......................................................... 6-6
Part locations ................................................................. 3-1
Pre-operation check list ................................................. 5-1
RRear knuckle pivots, lubricating ................................... 8-47
Recoil starter ................................................................ 4-14
Reverse indicator light ................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 1-1
Seat ............................................................................. 4-18
Shock absorber assemblies,
adjusting the front and rear ........................................ 4-20
Spark arrester, cleaning ............................................... 8-34
Spark plug, checking ................................................... 8-16
Specifications ............................................................... 10-1
Speed limiter ................................................................ 4-12
Stabilizer bushes, checking ......................................... 8-47
Starter (choke) ............................................................. 4-17
Start switch .................................................................... 4-6
Steering shaft, lubricating ............................................ 8-48
Storage .......................................................................... 9-2
Storage compartment .................................................. 4-19TTail/brake light bulb, replacing ..................................... 8-53
Throttle cable free play, adjusting ................................ 8-37
Throttle lever ......................................................... 4-11, 5-5
Tire pressure, measuring ............................................... 5-6
Tires ............................................................................... 5-5
Tire wear limit ................................................................ 5-7
Troubleshooting ........................................................... 8-56
Troubleshooting charts ................................................ 8-57VValve clearance ........................................................... 8-38
V-belt case drain plug .................................................. 8-35
U23D60E0.book Page 2 Thursday, March 15, 2007 7:59 PM