2008 YAMAHA AEROX50 low beam

INSTRUMENT AND CONTROL FUNCTIONS
3-2
3
EAU11002
Indicator and warning lights
EAU11020
Turn signal indicator light “”
This indicator light flashes when the
turn signal switch is pushed to the left or
right.
EAU11080
High beam indicator light “”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU11180
Oil level warning light “”
This warning light comes on when the
key is in the “” position or when the oil
level in the 2-stroke engine oil tank is
low during operation. If the warninglight comes on during operation, stop
immediately and fill the oil tank with Ya-
malube 2 or equivalent 2-stroke engine
oil of either JASO grade “FC” or ISO
grades “EG-C” or “EG-D”. The warning
light should go off after the 2-stroke en-
gine oil tank has been refilled.
NOTE:If the warning light does not come on
when the key is in the “” position or
does not go off after the 2-stroke en-
gine oil tank has been refilled, have a
Yamaha dealer check the electrical cir-cuit.CAUTION:
ECA10010
Do not operate the vehicle until you
know that the engine oil level is suf-ficient.
EAU11430
Coolant temperature warning light
“”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.CAUTION:
ECA10020
Do not operate the engine if it isoverheated.
1. Turn signal indicator light “”
2. High beam indicator light “”
3. Oil level warning light “”
TEMP
123
ZAUM0254
1. Coolant temperature warning light “”
TEMP
Km / h
E1/2
F
1
ZAUM0255

INSTRUMENT AND CONTROL FUNCTIONS
3-4
3
EAU12140
Fuel gauge The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the needle reaches
“E”, refuel as soon as possible.NOTE:Do not allow the fuel tank to empty itselfcompletely.
EAU12343
Handlebar switches Left
Right
EAU12400
Dimmer switch “/”
Set this switch to “” for the high
beam and to “” for the low beam.
EAU12460
Turn signal switch “/”
To signal a right-hand turn, push this
switch to “”. To signal a left-hand
turn, push this switch to “”. When re-
leased, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12500
Horn switch “”
Press this switch to sound the horn.
EAUM1131
Start switch “”
Push this switch while applying the
front or rear brake to crank the engine
with the starter.CAUTION:
ECA10050
See page 5-1 for starting instruc-tions prior to starting the engine.
1. Fuel gauge
E1/2
F
1
ZAUM0257
1. Horn switch “”
2. Turn signal switch “/”
3. Dimmer switch “/”
1. Start switch “”
1
2 3
ZAUM0259
1
ZAUM0261

PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
6
EAUM2110
Replacing the headlight bulb If the headlight bulb burns out, replace
it as follows.CAUTION:
ECA10670
It is advisable to have a Yamahadealer perform this job.
1. Remove cowling A. (See page
6-5.)
2. Disconnect the headlight coupler.
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
WARNING
EWA10790
Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooleddown.
4. Place a new headlight bulb into po-
sition, and then secure it with the
bulb holder.
5. Connect the coupler.
6. Install the cowling.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb 1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.CAUTION:
ECA10680
Do not overtighten the screws, oth-erwise the lens may break.
1. Headlight bulb holder
1
ZAUM0283
ZAUM0284