2008 YAMAHA AEROX50 lock

PERIODIC MAINTENANCE AND MINOR REPAIR
6-21
6
EAUM2110
Replacing the headlight bulb If the headlight bulb burns out, replace
it as follows.CAUTION:
ECA10670
It is advisable to have a Yamahadealer perform this job.
1. Remove cowling A. (See page
6-5.)
2. Disconnect the headlight coupler.
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
WARNING
EWA10790
Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooleddown.
4. Place a new headlight bulb into po-
sition, and then secure it with the
bulb holder.
5. Connect the coupler.
6. Install the cowling.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb 1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.CAUTION:
ECA10680
Do not overtighten the screws, oth-erwise the lens may break.
1. Headlight bulb holder
1
ZAUM0283
ZAUM0284

PERIODIC MAINTENANCE AND MINOR REPAIR
6-22
6
EAU24201
Replacing a turn signal light
bulb 1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screw.
CAUTION:
ECA11190
Do not overtighten the screw, other-wise the lens may break.
EAU25880
Troubleshooting Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your scooter re-
quire any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter prop-
erly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
lead to expensive repair bills.
ZAUM0285ZAUM0286

PERIODIC MAINTENANCE AND MINOR REPAIR
6-24
6 Engine overheating
WARNING
EWA10400


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissingsound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
NOTE:If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See NOTE.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.

INDEX
AAcceleration and deceleration ................ 5-2
Air filter element, cleaning ...................... 6-9BBattery .................................................. 6-18
Brake fluid, changing ............................ 6-15
Brake fluid level, checking .................... 6-15
Brake lever, front .................................... 3-5
Brake lever, rear ..................................... 3-5
Brake levers, lubricating ....................... 6-16
Braking ................................................... 5-3CCarburetor,adjusting ............................. 6-10
Care ........................................................ 7-1
Catalytic converter .................................. 3-7
Centerstand, checking and
lubricating ........................................... 6-16
Coolant ................................................... 6-8
Coolant temperature warning light.......... 3-2
Cowling and panel, removing and
installing ............................................... 6-5DDimmer switch ........................................ 3-4EEngine break-in ...................................... 5-4FFinal transmission oil .............................. 6-7
Front and rear brake lever free play,
checking ............................................. 6-13
Front and rear brake pads, checking .... 6-14
Front fork, checking .............................. 6-17
Fuel......................................................... 3-6
Fuel consumption, tips for reducing........ 5-3
Fuel gauge.............................................. 3-4Fuel tank cap........................................... 3-5
Fuse, replacing...................................... 6-20
HHandlebar switches ................................. 3-4
Headlight bulb, replacing....................... 6-21
High beam indicator light......................... 3-2
Horn switch ............................................. 3-4IIdentification numbers ............................. 9-1
Indicator and warning lights .................... 3-2KKey identification number ........................ 9-1
Kickstarter ............................................... 3-8MMain switch/steering lock ........................ 3-1
Model label .............................................. 9-2OOil level warning light .............................. 3-2PParking ....................................................5-4
Part locations .......................................... 2-1
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list........................... 4-2RRider seat ................................................ 3-8SSafe-riding points .................................... 1-4
Safety information ...................................1-1
Shock absorber assembly, adjusting
(Depends on models).......................... 3-10
Spark plug, checking ...............................6-6
Specifications .......................................... 8-1
Speedometer unit .................................... 3-3Starting off .............................................. 5-2
Starting the engine.................................. 5-1
Start switch ............................................. 3-4
Steering, checking ................................ 6-17
Storage ................................................... 7-3
Storage compartment A .......................... 3-9
Storage compartment B ........................ 3-10
TTachometer (Depends on models) ......... 3-3
Tail/brake light bulb, replacing .............. 6-21
Throttle cable free play, checking ......... 6-11
Throttle grip and cable, checking and
lubricating ........................................... 6-16
Tires ...................................................... 6-11
Troubleshooting .................................... 6-22
Troubleshooting charts ......................... 6-23
Turn signal indicator light ........................ 3-2
Turn signal light bulb, replacing ............ 6-22
Turn signal switch ................................... 3-4
Two-stroke engine oil.............................. 3-8
Two-stroke engine oil tank ...................... 3-7VVehicle identification number .................. 9-1WWheel bearings, checking..................... 6-18
Wheels .................................................. 6-13