2008 TOYOTA LAND CRUISER ESP

9
ITYPC034
Overhead consoleP. 332
Garage door opener switchesP. 352
Anti−glare inside rear view mirrorP. 79
Moon roof switchesP. 86
Vanity mirrorP. 338
SRS curtain shield airbagP. 102
Interior lightP. 326
Sun visorP. 337
Interior lightP. 326
A
Personal lightsP. 327
Personal lights
Interior light
P. 327
P. 326Rear seat entertainment
system
P. 285
: If equipped

10
1SET23
ITYPC005
B
Driving position memory switchesP. 62
Door lock switchP. 43
Window lock switchP. 83
Power window switchesP. 83
Pictorial indexInterior

11
P
R
N
+
SDPWR2ND ON/OFF SPEE
D
ITYPC035
ECT switchP. 154
Shift lock override buttonP. 478
Seat heater switchesP. 346
C
Shift leverP. 153
Crawl Control switchP. 197
Cigarette lighterP. 343
Power outletP. 344
AshtrayP. 341
AUX adapterP. 282
Parking brake leverP. 159

17
D
Roll sensing of curtain shield
airbags off switch
P. 116
Headlight cleaner switch P. 177
Power outlet main switchP. 344
Outside rear view mirror control switchesP. 256
Toyota park assist system switch P. 181
: If equipped
Instrument panel light control knobP. 161
Odometer/trip meter and trip meter
reset button
P. 160
Tilt and telescopic steering
control switch
P. 77
Card holderP. 336

18
For your information
Main Owner ’s Manual
Please note that this manual applies to all models and explains all
equipment, including options. Therefore, you may find some explana−
tions for equipment not installed on your vehicle.
All specifications provided in this manual are current at the time of
printing. However, because of the Toyota policy of continual product
improvement, we reserve the right to
make changes at any time with−
out notice.
Depending on specificati
ons, the vehicle shown in the illustration may
differ from your vehicle in terms of equipment.
Accessories, spare parts and modification of your Toyota
A wide variety of non−genuine spare parts and accessories for Toyota
vehicles are currently available in
the market. You should know that
Toyota does not warrant these prod ucts and is not responsible for
their performance, repair, or replacement, or for any damage they
may cause to, or adverse effect they may have on, your Toyota vehi−
cle.
This vehicle should not be modi
fied with non−genuine Toyota prod−
ucts. Modification with non−genuine Toyota products could affect its
performance, safety or durability
, and may even violate governmental
regulations. In addition, damage or performance problems resulting
from the modification may not be covered under warranty.

37
1−2. Opening, closing and locking the doors
1
Before driving
nCertification for the smart key system
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer−
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user ’s authority to operate the equipment.
FCC ID:NI4TMLF−5

42 1−2. Opening, closing and locking the doors
nCertification for wireless remote control
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer−
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTICE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. How−
ever, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
lConnect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
lConsult the dealer or an experienced radio/TV technician for help.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user ’s authority to operate the equipment.
FCC ID:HYQ14AAB
FCC ID:HYQ13BZS

45
1−2. Opening, closing and locking the doors
1
Before driving
Automatic door locking and unlocking systems
The following functions can be set or canceled:
nSetting and canceling the functions
To switch between setting and canceling, follow the procedure
below:
Close all the doors and switch the “ENGINE START STOP”
switch IGNITION ON mode. (Perform step 2 within 20 sec−
onds.)
Shift the shift lever to “P” or “N”,
press and hold the driver ’s door
lock switch (
or) for 5 sec−
onds then release.
The shift lever and switch posi−
tions corresponding to the
desired function to be set or can−
celed are shown as follows.
Function Operation
Shift position linked
door locking functionShifting the shift lever out of “P” locks all
doors.
Shift position linked
door unlocking functionShifting the shift lever to “P” unlocks all
doors.
Speed linked door lock−
ing functionAll doors are locked when the vehicle speed is
approximately 12 mph (20 km/h) or higher.
Driver ’s door linked door
unlocking function
All doors are unlocked when the driver ’s door
is opened within 10 seconds after turning the
“ENGINE START STOP” switch OFF.
STEP1
STEP 2