2008 TOYOTA 4RUNNER lights

140
When any of the side doors and back
door is unlocked using either the key or
the wireless remote control transmitter, the
light will come on and remain on for about
15 seconds before fading out.
The following adjustments can be made in
this system. For details, contact your
Toyota dealer.
Cancelling the door key or the wireless
remote control transmitter linked opera-
tion
Changing the duration of lighting
To prevent the battery being discharged,
the light will automatically turn off when
the key is removed and the door is left
opened for 30 minutes or more.
CY14027
Lighting the running boards and the
ground helps you easily to get in and
out of the vehicle in the night. The
lights come on when any of the side
doors is opened.
The lights remain on for about 15 seconds
after all the side doors are closed.
However, in the following cases, the light
go off immediately.
All the side doors and back door are
closed and locked.
The vehicle speed reaches 8 km/h (5
mph) or higher. When any of the side doors and back
door is unlocked using either the key or
the wireless remote control transmitter, the
lights will come on and remain on for
about 15 seconds before fading out.
To prevent the battery being discharged,
the light will automatically turn off when
the key is removed and the door is left
opened for 30 minutes or more.
Running board lights

157
Either of the following conditions may
occur, but do not indicate a malfunc-
tion:
The light may stay on for about 60
seconds after the engine switch is
turned to the ON" position. It is nor-
mal if it turns off after a while.
Depressing the brake pedal repeatedly
may turn on the light. It is normal if it
turns off after a few seconds.
(j) VSC OFF" Warning Light
The light flashing warns that there is a
problem somewhere in the following.
Vehicle stability control system
Traction control system
(two−wheel drive models)
Active traction control system
(four−wheel drive models)
AUTO LSD" system
(two−wheel drive models)
Downhill assist control system
(four−wheel drive models)
Hill−start assist control system
The light will come on when the engine
switch turned to ON", and will go off after
a few seconds. It is not a malfunction that the warning
light may stay on for 60 seconds after the
engine switch is turned to the ON" posi-
tion.
Depressing the brake pedal repeatedly
may turn on the lights. It is normal if they
go out after a few seconds.
If the light flashes while driving, the above
mentioned systems do not work. However,
as conventional braking operates when ap-
plied, there is no problem to continue your
driving.
In the following cases, contact your Toyota
dealer:
The warning light does not come on
after the engine switch is turned to
ON".
The warning light remains on after the
engine switch is turned to ON".
The warning light flashes while driving.
When the brake fluid level is too low, the
above mentioned systems will not operate
and the warning light comes on.
(k) Open Door Warning Light
This light remains on until all the side
doors and back door are completely
closed. (l) SRS Warning Light
This indicator comes on when the en-
gine switch is turned to the ON" posi-
tion. It goes off after about 6 seconds.
This means the SRS airbags and seat
belt pretensioners are operating proper-
ly.
This warning light system monitors the
airbag sensor assembly, front airbag sen-
sors, side and curtain shield airbag sen-
sors, curtain shield airbag sensors, driv-
er ’s seat position sensor, driver ’s seat belt
buckle switch, front passenger occupant
classification system and indicator light,
front passenger ’s seat belt buckle switch,
seat belt pretensioner assemblies, inflat-
ors, RSCA OFF" indicator light, intercon-
necting wiring and power sources.
If any of the following conditions occurs,
this indicates a malfunction of the airbags
or seat belt pretensioners. Contact your
Toyota dealer as soon as possible.
The light does not come on when the
engine switch is turned to the ON"
position or remains on for more than
6 seconds or flashes.
The light comes on or starts flashing
while driving.

159
CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light and low windshield
washer fluid level warning light)1. Apply the parking brake.
2. Open one of the side doors or back door.
The open door warning light should
come on.
3. Close the door. The open door warning light should go
off.
4. Turn the engine switch to ON", but do not start the engine.
All the service reminder indicators ex-
cept the open door warning light should
come on.
The following service reminder indica-
tors go off after a few seconds:
Engine oil replacement reminder light
ABS" warning light
Tire pressure warning light
RSCA OFF" indicator light
AUTO LSD" indicator light
VSC OFF" indicator/warning light
Slip indicator light
Height control indicator lights
Downhill assist control system indicator
light (four−wheel drive models)
Height control OFF" indicator light
The SRS warning light goes off after
about 6 seconds.
There may be the case that the ABS"
warning light (brake assist system
warning light), AUTO LSD" indicator
light, VSC OFF" indicator/warning light
or slip indicator light stay on for about
60 seconds after the engine switch is
turned to the ON" position. It is nor-
mal if they go out after a while.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by your Toyota
dealer as soon as possible.

169
Use the four−wheel drive control switch
knob and center differential lock switch
to select the transfer and center differ-
ential modes.
The H4" and L4" positions of the four−
wheel drive control switch knob provide
either lock or unlock mode of the center
differential. The center differential can be
locked or unlocked by pushing the center
differential lock switch.
Use the center differential lock system if
your wheels get stuck in a ditch, or when
you are driving on a slippery or bumpy
surface. When the center differential is
locked, the vehicle stability control system
is automatically turned off and the center
differential lock and VSC OFF" indicator
lights come on because the function that
controls engine performance interferes
with the process of freeing your wheels.NOTICE
As soon as the center differential lock
switch is turned on, the VSC OFF"
indicator light comes on. After the
wheels are out of the ditch or off the
slippery or bumpy surface, turn the
center differential lock switch off.
Make sure that the center differential
lock indicator and VSC OFF" indica-
tor lights turn off.
H4" (high speed position) and center
differential unlocked: Four−wheel drive
control switch knob at H4", center differ-
ential unlocked
Use this for normal driving on all types of
roads, from dry hard−surfaced roads to
wet, icy or snow−covered roads. This
position gives greater economy, quietest
ride, least wear and better vehicle control.
H4" (high speed position) and center
differential locked: Four−wheel drive con-
trol switch knob at H4", center differential
locked
Use this for greater traction when you
experience a loss of power, such as
wheel slipping, in the center differential
unlock mode. L4" (low speed position) and center
differential unlocked:
Four−wheel drive
control switch knob at L4", center differ-
ential unlocked
The 4LO" (low speed four−wheel drive)
indicator light comes on when the L4"
mode is selected.
Use this for maximum power and traction.
Use this for climbing or descending steep
hills, off−road driving, and hard pulling in
sand or mud.
In this mode, the braking feeling that oc-
curs when the wheels are negotiating a
sharp corner is further reduced than in the
L4" (low speed position) and center differ-
ential locked mode.
L4" (low speed position) and center
differential locked: Four−wheel drive con-
trol switch knob at L4", center differential
locked
The 4LO" (low speed four−wheel drive)
indicator light comes on when the L4"
mode is selected.

172
The center differential can be locked or
unlocked by pushing the center differential
lock switch.
Use the center differential lock system if
your wheels get stuck in a ditch, or when
you are driving on a slippery or bumpy
surface. When the center differential is
locked, the vehicle stability control system
is automatically turned off and the center
differential lock and VSC OFF" indicator
lights come on because the function that
controls engine performance interferes
with the process of freeing your wheels.
NOTICE
As soon as the center differential lock
switch is turned on, the VSC OFF"
indicator light comes on. After the
wheels are out of the ditch or off the
slippery or bumpy surface, turn the
center differential lock switch off.
Make sure that the center differential
lock indicator light and VSC OFF"
indicator light turn off.
H2" (high speed position, two−wheel
drive): Multi−mode control switch knob at
H2"
Use this for normal driving on dry hard−
surfaced roads. This position gives greater
economy, quietest ride, least wear and
better vehicle control.
H4" (high speed position, four−wheel
drive) and center differential unlocked:
Multi−mode control switch knob at H4",
center differential unlocked
The four−wheel drive indicator light comes
on when the H4" mode is selected.
Use this for greater traction than two−
wheel drive. (When you experience a loss
of power, such as wheel slipping.) This
position provides greater traction than
two−wheel drive.
H4" (high speed position, four−wheel
drive) and center differential locked:
Multi−mode control switch knob at H4",
center differential locked
The four−wheel drive indicator light comes
on when the H4" mode is selected.
Use this for greater traction when you
experience a loss of power, such as
wheel slipping, in the center differential
unlock mode. L4" (low speed position, four−wheel
drive) and center differential unlocked:
Multi−mode control switch knob at L4",
center differential unlocked
The four−wheel drive and 4LO" (low
speed four−wheel drive) indicator lights
come on when the L4" mode is selected.
Use this for maximum power and traction.
Use this for climbing or descending steep
hills, off−road driving, and hard pulling in
sand or mud.
In this mode, the braking feeling that oc-
curs when the wheels are negotiating a
sharp corner is further reduced than in the
L4" (low speed position, four−wheel drive)
and center differential locked mode.
L4" (low speed position, four−wheel
drive) and center differential locked:
Multi−mode control switch knob at L4",
center differential locked
The four−wheel drive and 4LO" (low
speed four−wheel drive) indicator lights
come on when the L4" mode is selected.

174
SHIFTING BETWEEN H2" AND H4"
(UNLOCKED)
To shift from H2" to H4" (unlocked),
reduce the vehicle speed to less than 100
km/h (62 mph) and turn the multi−mode
control switch knob fully clockwise.
If the four−wheel drive indicator light con-
tinues to blink when you operate the mul-
ti−mode control switch knob from the H2"
to the H4" position, this reminds you that
the transfer mode is not securely in H4"
mode. Drive straight ahead while acceler-
ating or decelerating.
If the four−wheel drive indicator and the
center differential lock indicator lights con-
tinue to blink and the buzzer sounds when
you operate the multi−mode control switch
knob from the H2" to the H4" position,
this reminds you that the vehicle speed is
above 100 km/h (62 mph). Reduce the
vehicle speed to less than 100 km/h (62
mph). Operate the switch knob again.To shift from H4" (unlocked) to H2",
turn the multi−mode control switch knob
fully counterclockwise.
This can be done at any speed.
If the four−wheel drive indicator light con-
tinues to blink when you operate the mul-
ti−mode control switch knob from the H4"
to the H2" position, this reminds you that
the transfer mode is not securely in H2"
mode. Drive straight ahead while acceler-
ating or decelerating, or drive forward or
backward in a short distance.
If the indicator light continues to blink
even if doing so, contact your Toyota
dealer as soon as possible. There may be
a trouble in the four−wheel drive system.
CAUTION
Never operate the multi−mode control
switch knob if the wheels are slip-
ping. Stop the slipping or spinning
before operating.
SHIFTING BETWEEN H4" (UNLOCKED)
AND H4" (LOCKED)
To shift between unlock and lock
modes in H4", push the center differen-
tial lock switch.
SHIFTING BETWEEN L4" (UNLOCKED)
AND L4" (LOCKED)
To shift between unlock and lock
modes in L4", push the center differen-
tial lock switch.
SHIFTING BETWEEN H4" AND L4"
To shift from H4" to L4",
bring the
vehicle to a complete stop with the brake
pedal held down with your foot, shift the
automatic transmission selector lever into
N" and push and turn the multi−mode
control switch knob fully clockwise.
To shift from L4" to H4", bring the
vehicle to a complete stop with the brake
pedal held down with your foot, shift the
automatic transmission selector lever into
N" and turn the multi−mode control switch
knob counterclockwise.
(c) Shifting procedure

176
You may feel vibration or noise in your
vehicle, caused by operation of the
brakes. This indicates the system is
functioning properly.
The slip indicator light comes on for a few
seconds when the engine switch is turned
to ON". If the indicator light does not
come on when the engine switch is turned
on, contact your Toyota dealer.
The brake actuator temperature increases
during continuous operation of the traction
control system, the AUTO LSD" system,
the vehicle stability control system and
the hill−start assist control system such
as on slippery roads.
If the brake actuator temperature becomes
too high while any of the systems is oper-
ating, a buzzer will start to sound intermit-
tently to indicate that the traction control
system can no l onger operate. In this
case, immediately stop your vehicle at a
safe place.
If the system continues to operate, the
buzzer sound changes from intermittent to
continuous. (The continuous buzzer
sounds for about 3 seconds.) At the time the slip indicator light will
come on and the traction control system
temporarily stops operating in order to
protect the brake actuator. (Although the
traction control system does not operate,
there is no problem to continue your driv-
ing.) The system will be automatically re-
stored after a short time and the slip indi-
cator light goes out.
CY16075
TRACTION CONTROL OFF MODE
If your wheels get stuck in an ditch
when you are driving on a severe off
road and sand, turn off the traction
control system. This system that con-
trols engine performance interferes with
the process of freeing your wheels.
To turn off: Briefly push the VSC OFF"
switch.
The AUTO LSD" and slip indicator lights
will come on.
The vehicle stability control system is al-
ways activated, even if the traction control
system is turned off.

177
To turn on: Briefly push the VSC OFF"
switch once again.
The AUTO LSD" and slip indicator lights
will go off.
If the engine is turned off while the
AUTO LSD" and slip indicator lights are
on and then restarted, the indicator lights
will turn off automatically.
When you push and hold the VSC OFF"
switch for 3 seconds or more with the
vehicle stopped, turn off the vehicle stabil-
ity control system. See Vehicle stability
control system" on page 183 in this Sec-
tion.
AUTO LSD" and slip indicator lights come
on for a few seconds when the engine
switch is turned to ON". If the indicator
lights do not come on when the engine
switch is turned to ON", contact your
Toyota dealer.
CAUTION
Do not drive with the traction control
system continuously turned off.
CY16074
VSC OFF" warning light
This light flashing warns that there is a
problem somewhere in the following.
Traction control system
AUTO LSD" system
Vehicle stability control system
Hill−start assist control system
When the system is normal and the en-
gine switch is turned to ON", the warning
light will come on and will go off after a
few seconds.
It is not a malfunction that the warning
light may stay on for 60 seconds after the
engine switch is turned to ON". Depressing the brake pedal repeatedly
may turn on the light. It is normal if it
goes out after a few seconds.
If the VSC OFF" warning light flashes
while driving, the traction control system
does not work. However, as normal brak-
ing operates when being applied, there is
no problem to continue your driving.
In the following cases, contact your Toyota
dealer:
The warning light does not come on
after the engine switch is turned to
ON".
The warning light remains on after the
engine switch is turned to ON".
The warning light flashes while driving.