2008 TESLA ROADSTER length

Vehicle security4-8
Doors, locks, and security
Ve h i c l e P I N c o d eAs an alternate level of vehicle security, you
can restrict operation of your vehicle until a
PIN code is entered. The PIN code is used by
the following features that can be selected on
the Touch Screen’s parked screen (shown
above, the parked screen is active whenever
the hand brake is engaged).
Tesla Motors requires that you set your PIN
code when you receive your vehicle.
Note: If at some point in the future you sell
your vehicle, remember to inform the new
owner of the PIN code.
Setting the PIN code
With the hand brake engaged, touch
the SETTINGS icon on the main ‘parked
screen to display the settings screen.
Press the right arrow icon to navigate to the
second settings screen.
Touch Security PIN .
If a PIN code has been previously set, you will
be asked to enter the old PIN code. Enter the
old PIN code by touching the numbers on the
screen and then touch OK. If you enter an
incorrect PIN code, an invalid entry message
will be displayed. Either enter the correct PIN
code or touch the EXIT icon to return to the
previous screen. You will be then be asked to enter the new
PIN code. Enter a new PIN code and then
touch
OK.
Note: The PIN code must be between four
and eight digits in length.
You will then be asked to confirm the new PIN
code. Enter the new PIN code again and then
touch OK.
If the PIN code does not match the previously
entered code a message will be displayed
telling you that the PINs differ and you will
need to enter the PIN code again.
Valet mode. See
Va l e t m o d e ,
page 4-11 .
PIN Lock. See PIN lock,
page 4-10 .
Roadster OHB.book Page 8 Th ursday, October 2, 2008 8:59 AM

Vehicle dimensions and weights
11-15
Technical specifications
Vehicle dimensions and weightsExterior dimensionsTR0261
HED G
F
C
BA
A Overall length 155.4 in3,946 mm
B Overall width (including mirrors) 72.9 in1,851 mm
C Overall height (mid laden weight) 44.35 in1,126.5 mm
D Wheel base 92.6 in2,351 mm
E Front overhang 34.3 in871 mm
F Rear overhang 28.5 in723 mm
G Ground clearance (mid laden weight) 5.12 in130 mm
HTrack - Front 57.7 in1,455.6 mm
Track - Rear 59.0 in1,484.5 mm
Approach (ramp) angle - Front 11°
Approach (ramp) angle - Rear 18°
Breakover angle 12.7°
Roadster OHB.book Page 15 Thursday, October 2, 2008 8:59 AM

Subsystem specifications11-18
Technical specifications
Front suspension
Rear suspension
BrakesTypeIndependent. Upper and lower unequal length wishbones.
Co-axial coil spring/telescopic damper. Sway bar.
Alignment optimum0.1 mm toe-in
tolerance 0.5 mm toe-out to 0.7mm toe-in. overall
Maximum side to side 0.3 mm
Camber optimum- 0.1°
tolerance + 0.1° to - 0.3°. Maximum side/side 0.2°
Castor optimum+ 3.8°
tolerance + 3.5° to 4.1°. Maximum cross castor 0.35°Type Independent. Upper and lower unequal length wishbones.
Co-axial coil spring/telescopic damper. Sway bar.
Alignment optimum3.0 mm toe-in
tolerance 2.4 mm toe-in, to 3.6 mm toe-in.
Maximum side to side 0.3 mm
Camber optimum- 1.8°
tolerance - 1.6° to - 2.0°. Maximum side to side 0.2°Type Hydraulically operated. Tandem master cylinder with vacuum servo and Anti-lock
Braking System.
Discs Ventilated front and rear discs.
Hand brake Cable operation of rear calipers. Self adjusting for pad wear.Roadster OHB.book Page 18 Thursday, October 2, 2008 8:59 AM