2008 SUZUKI GRAND VITARA warning

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Diesel Particulate Filter (DP~ ;::D.:..p.:..j=®----=:w:..::a::..:rn..:.:i:..::ng~lig~h:..:..:t~ _____ _____, The DPj=® filters off the soot 'particles in the exhaust gas, so the DPp!9 could get clogged depending on the driving condi­tion. The DPPW is cleaned by the regener­ating function that combusts the soot
particles in the DPPW by raising the
exhaust gas temperature during driving.
A WARNING
Keep away from the exhaust pipe
when the engine is running. If the DPj=® is regenerating, the exhaust
gas temperature could be higher.
NOTE: When you drive your vehicle, white smoke
may be emitted depending on the grade of fuel used. This is due to the particle filter
regenerating automatically, and does not
affect the way the vehicle runs.
3-11
64J244
If the DPpID warning light comes on when
driving, the DPpID is nearly clogged. You should regenerate the DPpID when the DPPW warniqg light comes on. To regener­ate the DPp!9, you must drive the vehicle
until the light goes out, at a speed of 75 km/h (47 mph) or higher for a while (max. 30 minutes).
However, you should drive carefully and
within the legal speed limit, and should
take in to consideration the surrounding
traffic condition. If you drive your vehicle
until the light goes out, the regeneration of
the DPPW will be completed.
CAUTION
Be sure to regenerate the DPj=® when
the DPj=® warning light comes on.
Failure to regenerate the DPj=® will cause a vehicle malfunction due to the clogged filter.
Using the Transmission
Manual Transmission
Starting off
650449
To start off, depress the clutch pedal all the
way to the floor and shift into 1 st gear. After releasing the parking brake, gradually release the clutch. When you hear a
change in the engine's sound, slowly press
the accelerator while continuing to gradu­
ally release the clutch.
Shifting All forward gears are synchronized, which
provides for quiet, and easy shifting.
Always push
in the clutch pedal fully before
shifting gears.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
A WARNING
• Reduce your speed and downshift to a lower gear before going down
a long or steep hill. A lower gear
will allow the engine to provide
braking. Avoid riding the brakes or they may overheat, resulting in
brake failure.
• When driving on slippery roads, be
sure to slow down before down­shifting. Excessive and or sudden
changes in engine speed may
cause
loss of traction, which could cause you to lose control.
• Make sure that the vehicle is com­
pletely stationary before you shift into reverse.
CAUTION
• To help avoid clutch damage, do not use the clutch pedal as a foot­rest while driving or use the clutch to keep the vehicle stationary on a
hill. Depress the clutch fully when
shifting.
• When shifting or starting off, do not race the engine. Racing the engine
can shorten engine life and affect
smooth shifting.
3-13
5-Speed Automatic Transmission
EXAMPLE
(1) Power mode selector switch
D:
66J055
5-speed automatic transmission mode 4: 4-speed automatic transmission mode
The 4-speed mode is suitable for the fol­
lowing driving conditions: • Driving on hilly, winding roads
-You can drive more smoothly with less frequent gearshifting
• Going down a steep hill -Some engine braking is provided
NOTE:
With the transfer switch in the "4L LOCK" position, the 5-speed automatic transmis­sion will remain in the 4-speed mode.
Power mode selector switch
A/T
POWER
650448
When you need more power for climbing
hills or smooth starting on slippery road,
push the "AfT POWER" switch. To activate
the power mode selector, push the "AfT POWER" switch, and the "POWER" indica­tor light in the instrument cluster comes on. To deactivate, push the switch again, and
the "POWER" indicator light goes off.
Power driving mode When the "AfT POWER" switch is on with
shift in "0" (Drive), "4" (Low 3) or "3" (Low 2) position, if you depress the accelerator
pedal, the shifting points are delayed so
the engine can rev higher in each gear.
Therefore, you can drive more powerfully than normal driving.

Downloaded from www.Manualslib.com manuals search engine Gearshift lever
EXAMPLE
66J056
The gearshift lever is designed that it can not be shifted out of the "P" position unless the ignition switch is in the "ON" position
and the brake pedal is depressed.
A WARNING
Always depress the brake pedal before shifting from "P" (Park) (or "N" (Neutral) if the vehicle is station­ary) to a forward or reverse gear, to help prevent the vehicle from moving unexpectedly when you shift.
For all normal driving, make sure that the "POWER" indicator light is off, then put the
gearshift lever into "0" (Drive). Use. the
other gearshift lever positions as described below:
P (Park) Use this position to lock the transmission
when the vehicle is parked or when start­ing the engine. Shift into Park only when
the vehicle is completely stationary.
A WARNING
If you have a 4-wheel drive vehicle, never leave the transfer switch in uN" (Neutral) when parked.
Otherwise the vehicle may roll even if the transmission is in Park.
R (Reverse)
Use this position to reverse the vehicle
from stop. Make sure that vehicle is com­
pletely stationary before shifting into
Reverse.
N (Neutral) Use this position for starting the engine if
the engine stalls and you need to restart it while the vehicle is moving. You may also shift into Neutral and depress the brake pedal to hold the vehicle stationary during idling.
OPERATING YOUR VEHICLE
D (Drive) Use this position for all normal driving.
With the gearshift
lever in "0" range you can get an automatic downshift by press­ing the accelerator pedal. The higher the vehicle speed is, the more you need to press the accelerator pedal to get a down­shift.
4 (Low 3) . Use this position for driving on moderate uphill and downhill gradients. The engine
braking effect on moderate downhills can be used in this position. The transmission
shifts up only to 4th gear.
3 (Low 2) Use this position to provide extra power
when climbing hills, or to provide engine
braking when going down hills.
NOTE: In these 4 or 3 positions, if the power mode
selector switch is turned to the "ON" posi­tion, the transmission will not downshift
into "I.!' (Low 1).
L (Low 1) Use this position to provide maximum
power when climbing steep hills or driving
through deep snow or mud, or to provide
maximum engine braking when going
down steep
hills.
3-14

Downloaded from www.Manualslib.com manuals search engine Slippery road mode
When the "AfT POWER" switch is on with
shift in "2" (Low 2) position, the gear will be
fixed in second while driving or when start
driving. Therefore, you can drive smoothly
on slippery road.
NOTE: • When you start driving with the gearshift lever in "2" (Low 2) position while the "AI T POWER" switch is on, the gear will be fixed in second. If you need to shift up, shift the' lever into "3" (Low 3) or "0" (Drive) position. • When the "AfT POWER" is on, if you
shift the gearshift lever from "3" (Low 3) or "0" (Drive) position to "2" (Low 2) posi­tion, the gear will be fixed in second. Gearshift
lever
64J142
The
gearshift lever is designed that it can­not be shifted out of the "P" position unless
the ignition switch is in the "ON" position and. the brake pedal is depressed.
A WARNING
Always depress the brake pedal before shifting from' "P" (Park) (or "N" (Neutral) if the vehicle is station­ary) to a forward or reverse gear, to help prevent the vehicle from moving
unexpectedly when you shift.
OPERATING YOUR VEHICLE
For all normal driving, make sure that the "POWER" indicator light is off, then put the
gearshift lever into "0" (Drive). Use the
other gearshift lever positions as described
below: .
P (Park)
Use this position
to lock the transmission
when the vehicle is parked or when start­ing the engine. Shift into Park only when
the vehicle is completely stationary.
A WARNING
If you have a 4-wheel drive vehicle,
never leave the transfer switch in "N" (Neutral) when parked.
Otherwise the vehicle may roll even if the transmission is in Park ..
R (Reverse) Use this position to reverse the vehicle from stop. Make sure that vehicle is com­
pletely stationary before shifting into
Reverse.
N (Neutral)
Use this position for starting the engine if
the engine
stalls and you need to restart it while the vehicle is moving. You may also
shift into Neutral and depress the brake
pedal to hold the I('ehicle stationary during
idling.
3-16

Downloaded from www.Manualslib.com manuals search engine Description of Transfer Switch Positions
N (Neutral)
64J223
OPERATING YOUR-VEHICLE
In this position, engine power is not sup­plied to the front or rear axles. Only use
this position for towing your vehicle. When you turn the transfer switch to the "N" position, "N" indicator will come on with
the buzzer sound.
A. WARNING
Never leave the transfer switch in UN" (Neutral) when parked.
When the transfer switch is in uN"
(Neutral), the vehicle may roll even if the transmission is in gear or in Park.
3-20

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
From 4H to N
64J209
Stop the vehicle completely, place the
transmission in uN" (Neutral) and depress
the brake pedal and the clutch pedal fully (if equipped), then push in and turn the
switch to the mark (1) at the left of the uN" position, and hold the switch in this posi­
tion for 5 seconds until the uN" indicator blinks, then turn the switch to the uN" posi­
tion. When
you turn the transfer switch to the uN" position, uN" indicator will come on with
the buzzer sound.
3-25
CAUTION
• Be sure to stop the vehicle com­
pletely before operating the trans­fer switch to shift between "N" and "4H", or between "4H LOCK" and "4L LOCK".
• Do not shift between "4H" and "4H
LOCK" unless the front wheels are
in the straight-ahead position and
we recommend
that the vehicle speed be less than 1 00 km/h (60 mph).
Do not operate the transfer switch
while tires are racing.
• Do not operate your vehicle in "4H
LOCK" or "4L LOCK" on dry, hard
surfaces. (Continued)
CAUTION
(Continued) • Do not operate the vehicle while a
4WD mode indicator is blinking except when shifting between "4H" and "4L LOCK".
If you operate the vehicle while a
4WD mode indicator is blinking, a
buzzer will sound and the transfer will shift to "N" (Neutral) to prevent
transfer case damage.
In this case, use the following pro­cedure.
1) Release your foot from the accel­erator pedal and depress the
brake pedal to stop the vehicle
completely.
2) Depress the clutch pedal fully (if
equipped) or shift the automatic transmission gearshift lever to the "N" position. 3) If the transfer does not shift from "N" although you perform 1) and 2), turn the transfer switch to the
position previously selected and
operate the switch again.
NOTE: The information display shows the warning
and indicator message when the transfer
system
is operated, or has a problem.

Downloaded from www.Manualslib.com manuals search engine OPERATING YOUR VEHICLE
Warning and Indicator messages
Transfer
Switch Operation Warning
and Indicator messages
In any position
In "N" position
Switching between
"4H" and "4H LOCK"
In "4H" position
3-27
I 79K074
79K077
79K078
I t¢-I USE 4HL MC'DE
79K079
Master Warn­ing Indicator
Blinks
Blinks
Off
Blinks
Sound
Off
Series
of
Beeps
Off
Beep
Cause and Remedy
There may be a problem with the 4WD
system.
Have your vehicle inspected by an
authorized
SUZUKI dealer.
This message informs you that the
transfer switch is in
"N", which is used only for towing your vehicle,
Move the transfer switch to a different
position
unless you are planning to tow
your vehicle,
This message informs you the 4WD
mode is switching,
Tires are slipping,
Turn the transfer switch to
"4H LOCK" or "4L LOCK" position.

Downloaded from www.Manualslib.com manuals search engine Transfer Switch Operation
Switching between U4H LOCK" and U4L LOCK"
Switching between U4H" and UN"
Warning and Indicator messages
I 1).'110 .8.CCEL ':'FF 1<>1 OE."-.RSHIFT I·.J
79K080
79K081
79K082
I 1<>1 SV'-iIT':Hlf'.JG
79K083
Master Warn­ing Indicator
Off
Off
Off
Off
Sound
Series of Beeps
Series of Beeps
Beep or
Off
Off
OPERATING YOUR VEHICLE
Cause and Remedy
(For automatic transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal.
Shift the automatic transmission gear­shift lever to the uN" position.
(For
manual transmission)
The desired transfer gear has not been
engaged.
Release your foot from the accelerator
pedal.
Depress the brake pedal and clutch
pedal.
The desired transfer gear has not been
engaged.
Turn the transfer switch back to the pre­
viously selected position, and operate
the transfer switch again.
This message informs
you the 4WD
mode is switching.
Do not move your vehicle.
3-28