Downloaded from www.Manualslib.com manuals search engine INSPECTION AND MAINTENANCE
Drive Belt
A WARNING
When the engine is running, keep
hands, hair, clothing, tools, etc. away from the moving fan and drive belts.
(For Gasoline Engine Model) Make sure the drive belt tension is correct. If the belt is too loose, insufficient battery
charging, engine overheating, poor power
steering, poor air conditioning, or exces
sive
belt wear can result. When you press the belt with your thumb midway between the pulleys, there should be a deflection
according to the following chart.
The belts should also be examined to
ensure that they are not damaged.
(For
2.0 L, 2.4 Lor 3.2 L gasoline engine) Check the accessory drive belt only for
damage. You do not need check it for tension as it has an automatic tensioner.
If you need to replace or adjust the belt have it done by your SUZUKI dealer.
(For Diesel Engine Model) The drive belt tension is adjusted automatically.
7-7
L4 1.6 L
L4 2.0 L
GE DEF:
7-9 mm (0.28 -
0.35 in.)
ADS
DEF: 9-10 mm (0.35 -0.39 in.)
->: 100 N (10 kg, 22 Ibs) press ADS: Accessory drive belt GE: Generator DEF: Deflection PS: Power steering pump AC: Air conditioner compressor AC
64J177
Downloaded from www.Manualslib.com manuals search engine Selection of Coolant CAUTION
SUZUKI LLC: Super (Blue) coolant;
SUZUKI LLC: Super (Blue) coolant is already diluted to the proper percent
age. Do not dilute with distilled water additionally. Doing so may result in the possibility of freezing coolant and/or overheating.
To maintain optimum performance and durability of your engine, use SUZUKI Genuine Coolant or equivalent.
NOTE: If you replace the engine coolant other
than the SUZUKIl:.LC: Super (Blue), follow
.the schedule of SUZUKI LLC: Standard
(Green). To see the detail of the maintenance schedule, refer to "Periodic Maintenance Schedule" in this section.
This type of coolant is best for your cooling system as it: • Helps maintain proper engine temperature. • Gives proper protection against freezing
and boiling.
• Gives proper protection against corro-
sion and rust. Failure to use the proper coolant can damage your cooling system. Your authorized SUZUKI dealer can help you select the
proper coolant.
CAUTION
To avoid damaging your cooling system: • Always use a high quality ethylene
glycol base non-silicate type coolant diluted with distilled water at the correct mixture concentration. • Make sure that the proper mix is 50/ 50 coolant to distilled water and in no case higher than 70/30. Concentrations greater than 70/30 coolant to distilled water will cause overheating conditions. • Do not use straight coolant nor plain water (except SUZUKI LLC: Super (Blue».
• Do not add extra inhibitors or additives. They may not be compatible with your cooling system. • Do not mix different types of base coolants. Doing so may result in accelerated seal wear and/or the possibility of severe overheating and extensive engine/automatic
transmission damage.
INSPECTION AND MAINTENANCE
Coolant Level
Check Check the coolant level at the reservoir
tank, not at the radiator. With the engine cool, the coolant level should be between
the "FULL (MAXI)" and "LOW (MINI)" marks.
Adding Coolant
(For Gasoline Engine Model) If the coolant level is below the "LOW" mark, more coolant should be added. Remove the reservoir tank cap and add coolant until the reservoir tank level reaches the "FULt..:' mark. Never fill the reservoir tank above the "FULt..:' mark.
(For
Diesel Engine Model)
A. WARNING
It is hazardous to remove the degassing tank cap for Diesel engine when the water temperature is high,
because scalding fluid and steam may be blown out under pressure. Wait· until the coolant temperature has lowered before removing the cap.
If the coolant level is below the "MINI" mark, more coolant should be added. When the engine is cool, remove the degassing tank cap by turning it antic lockwise slowly to release any pressure. And add coolant until the degassing tank level reaches the "MAXI" mark. Never fill the
degassing tank above the "MAXI" mark.
7-14
