Page 127 of 314
Driving and parking
126
>> Controls.Brake pedal
The brake pedal has two brake circuits inde
pendent of each other. A brake servo is used
during braking (when the engine is running) to
increase pedal force.
G
Warning!
When leaving the vehicle, always remove
the key from the starter switch, take it
with you, and lock the vehicle. Do not
leave children unattended in the vehicle,
or with access to an unlocked vehicle.
Children could release the parking brake
and/or move the gear selector lever from
park positionP, either of which could
result in an accident and/or serious
personal injury.
G
Warning
Make sure that absolutely no objects are
obstructing the pedals’ range of move
ment. Keep the driver’s footwell clear of
all obstacles. If there are any floormats*
or carpets in the footwell, make sure that
the pedals still have sufficient clearance.
During sudden driving or braking maneu
vers, objects could become caught be
tween the pedals, reducing or eliminating
entirely the driver's ability to brake or
accelerate. This could lead to accidents
and injury.
G
Warning!
Considerably more effort will be required
to apply the brakes if
• the brake servo has failed
• a brake circuit has failed
• the engine is switched off, e. g. for
towing the vehicle
The braking distance is likewise greater.
Make sure that the engine is running
whenever the vehicle is rolling. Have the
brake system repaired at an authorized
smart center, if there is a fault in the
brake system.
Page 128 of 314
Driving and parking
>> Controls.
127
1
Brake pedalIf a brake circuit has failed (
page 238),
• you must depress the brake pedal further
down to achieve the same effect
• the braking distance is increased
i
The brake servo will only function with the
engine switched on.
Turning off the engine>Depress the brake pedal.
>Press the release button (
page 122) to
disengage the gear selector lever lock.
>Move the gear selector lever to park
positionP.
!
Always set the parking brake in addition to
shifting to park positionP (
page 125).
>Release the brake pedal.
>Turn the key in the starter switch to
position0.
>Remove the key from the starter switch.
The immobilizer is activated.
P42.10259131
G
Warning!
In the event of the vehicle needing to be
towed, a significantly greater amount of
pedal pressure will be required when the
engine is switched off.
Page 130 of 314
Transmission
>> Controls.
129 Shifting procedure
The transmission selects individual gears
automatically, depending on:
• the gear selector lever
positionD(
page 129)
• the position of the accelerator
(
page 131)
• the vehicle speed
• uphill or downhill grades
Press release button
1 (page 128) to
disengage the gear selector lever lock when
moving the gear selector lever from
•P toR,N, orD
•R toP
•N toR orP
!
Allow engine to warm up under low load
use. Do not place full load on the engine until
the operating temperature has been reached.
Shift into reverse gearR or parking
positionP only when the vehicle is stopped.
Avoid spinning of a drive wheel for an extend
ed period when driving off on slippery road
surfaces. Otherwise, the the drivetrain could
be damaged, which is not covered by the smart
Limited Warranty.
With manual gearshiftingM selected
(
page 132), you can use the gear selector
lever or steering wheel gearshift control
1
to change the gears manually.
Gear selector lever positions
1 Model passion only.
Effect
ì
Park position
Gear selector lever position when
the vehicle is parked. Place the
gear selector lever in park
positionP only when the vehicle is
stopped. The park position is not
intended to serve as a brake when
the vehicle is parked.
Rather, the driver should always
set the parking brake in addition to
placing the gear selector lever in
park positionP to secure the
vehicle.
The key can only be removed from
the starter switch with the gear
selector lever in park positionP.
With the key removed, the gear
selector lever is locked in park
positionP.
Page 132 of 314
Transmission
>> Controls.
131 Driving tips
Accelerator position
Your driving style influences the
transmission’s shifting behavior:
Less throttle, earlier upshifting
More throttle, later upshifting
Kickdown
Use kickdown when you want maximum
acceleration.
>Press the accelerator past the point of
resistance.
Depending on the engine speed the
transmission shifts into a lower gear.
>Ease on the accelerator when you have
reached the desired speed.
The transmission shifts up again.Stopping
When you stop briefly, e.g. at traffic lights:
>Leave the transmission in gear.
>Hold the vehicle with the brake.
When you stop for a longer period with the
engine idling and/or on a hill:
>Set the parking brake.
>Move the gear selector lever to park
positionP.
Working on the vehicle
G
Warning!
When leaving the vehicle, always remove
the key from the starter switch, take it
with you, and lock the vehicle. Do not
leave children unattended in the vehicle,
or with access to an unlocked vehicle.
Children could move the gear selector
lever from park positionP, which could
result in an accident and/or serious
personal injury.
G
Warning!
When working on the vehicle, set the
parking brake and move the gear selec
tor lever to park positionP. Otherwise
the vehicle could roll away.
Page 137 of 314
Instrument cluster
136
>> Controls.
Multifunction displayThe following displays and indicators appear
in the multifunction display:1
Status indicator with:
• Trip odometer display
• Maintenance service interval display
• Reserve fuel display
2
Main odometer display or when active
distance to next maintenance service
3
Transmission position indicator
4
Digital clock
5
Outside temperature display
6
Fuel level displayMultifunction display illumination
The multifunction display illumination comes
on when the starter switch is in position1.
It goes out after approximately 30 seconds
when the starter switch is in position0.
For adjusting the multifunction display
illumination, see "Adjusting instrument clus
ter illumination“ (
page 141).Fuel level display/reserve fuel indicator
Fuel level display
The fuel level display shows the tank's fuel
level with the aid of eight segments. The num
ber of dark segments indicates the fuel level
in the tank.
If all eight segments are dark, the tank is full. P54.32517431
G
Warning!
No messages will be displayed if either
the instrument cluster or the multifunc
tion display is inoperative.
As a result, you will not be able to see
information about your driving condi
tions, such as speed, outside tempera
ture, or warning/indicator lamps. Driving
characteristics may be impaired.
If you must continue to drive, please do
so with added caution. Visit an authorized
smart center as soon as possible.P54.32517631
Page 139 of 314
Instrument cluster
138
>> Controls.
Selecting display for status
indicatorYou can select the information to be displayed
in the status indicator:
• Trip odometer display (
page 139)
• Maintenance service interval display
(
page 139)
• Reserve fuel indicator (
page 140)
1
Selecting display for status indicator/
setting the clock/activating maintenance
service interval display
2
Setting the clock/adjusting instrument
cluster illuminationDigital clock
> Activating time setting: Press right
button
2 (page 138) for approximately
five seconds.
The colon in the digital clock starts
flashing.
> Setting the time in 1 minute increments:
Press left button
1 or right button
2
(
page 138) repeatedly until the desired
time is set.>Setting the time quickly: Press left
button
1 or right button
2 (page 138)
for longer than one second.
The setting speed accelerates.
> Setting the time in 10 minute increments:
Press left button
1 or right button
2
(
page 138) for longer than five seconds.
The time is set in 10 minute increments.
>Confirm time setting: Refrain from pressing
either left button
1 or right button
2
(
page 138) for more than five seconds.
The colon in the digital clock stops flashing.
The time is set.
i
The digital clock in the multifunction
display is not synchronized with the cockpit
clock*.
P54.32517831
Page 141 of 314
Instrument cluster
140
>> Controls. Reserve fuel indicator
> Selecting reserve fuel indicator: Press left
button
1 (page 138) repeatedly until the
reserve fuel indicator appears in the status
indicator.
i
The reserve fuel indicator is only
displayed when driving on reserve fuel.
For more information on the reserve fuel indi
cator, see "Fuel level display/reserve fuel in
dicator" (
page 136).
Auxiliary instruments*1
Tachometer
2
Cockpit clock
Tachometer*
The tachometer can be turned by
approximately 90°.
The tachometer illumination comes on when
you turn the key in the starter switch in
position1.
The tachometer displays the engine speed in
units of 1000 rpm.
!
Do not hang any objects on the
tachometer.
This could cause the tachometer to be torn
from its mountings and damage it.
Cockpit clock*
The cockpit clock can be turned by
approximately 90°.
The cockpit clock illumination comes on when
you turn the key in starter switch to position1
and the parking lamps are switched on. P68.10361631
Page 142 of 314
Instrument cluster
>> Controls.
141
The buttons for setting the time are on the top
of the cockpit clock.1
Setting the time forward
2
Setting the time back> Setting the time forward in 1 minute
increments
: Press button
1 repeatedly
until the desired time is set.
> Setting the time forward quickly: Press
button
1 for longer than two seconds.
The setting speed accelerates.
> Setting the time back in 1 minute
increments: Press button
2 repeatedly
until the desired time is set.
> Setting the time back quickly: Press
button
2 for longer than two seconds.
The setting speed accelerates.
!
Do not hang any objects on the cockpit
clock.
This could cause the cockpit clock to be torn
from its mounting and damage it.
Adjusting instrument cluster
illuminationYou can adjust the illumination of the
switches, the dials in the instrument cluster,
the radio*, the climate control* panel and the
auxiliary instruments*.
Five settings are possible.
>Make sure that the key in the starter switch
is turned to position1.
>Switch on the parking lamps.
> To brighten or dim illumination: Press right
button
2 (page 138) repeatedly until the
desired setting is reached.
The current setting is stored. P68.10361531
