2008 SMART FORTWO COUPE ignition

Starter switch positions
>> Controls.
91
Starter switch0For removing key
1Ignition (power supply for all electrical
consumers) and driving position
All lamps (except low beam headlamp
indicator lamp, high beam headlamp
indicator lamp, and turn signal indicator
lamps unless activated) in the instrument
cluster come on. If a lamp in the instru

ment cluster fails to come on when the
ignition is switched on, have it checked
and replaced if necessary. If a lamp in the
instrument cluster remains on after start

ing the engine or comes on while driving,
refer to "Warning and indicator lamps in
the instrument cluster" (

page 237).
2Starting (

page 122)
i
When you switch on the ignition, the indi

cator and warning lamps (except low beam
headlamp indicator lamp, high beam headlamp
indicator lamp, and turn signal indicator
lamps unless activated) in the instrument
cluster come on. The indicator and warning
lamps (except low beam headlamp indicator
lamp, high beam headlamp indicator lamp, and
turn signal indicator lamps if activated) will go
out when the engine is running. This indicates
that the respective systems are operational. P82.00
2491
31

Lighting>> Controls.
107 Hazard warning flasher
The hazard warning flasher can be switched
on at all times, even with the key removed from
the starter switch.1
Hazard warning flasher switch
>Switching on: Press hazard warning flasher
switch
1.
All turn signal lamps are flashing.
>Switching off: Press hazard warning flasher
switch1 once more.
Interior lightingThe interior lamp comes on for a period of
time when you open the doors, or lock or
unlock the vehicle with the key.
It goes out
• immediately after switching off the ignition
with all doors closed,
• after 30 seconds if the doors are not
opened,
• after 15 seconds if all doors are closed,
• after 10 minutes if at least one door is open.The rocker switch can be set to three differ

ent positions.
1
Interior lamp
2
Switching on the automatic control
3
Off
4
Continuous operation P54.25
5341
31
P82.20
2954
31

Driving and parking
>> Controls.
125
>Properly stop and park the vehicle.
>Depress the brake pedal.
>Pull up the parking brake lever as many
notches as possible (

page 125).
When the ignition is switched on or the
engine is running, the brake warning
lamp; (USA only) or3 (Canada only)
in the instrument cluster comes on.
>Release the brake pedal.
Parking brake
The parking brake serves to secure the vehi

cle against rolling away when it is stationary
or parked.
1
Parking brake lever
2
Release button
>Applying: Pull up parking brake lever
1 as
many notches as possible.
When the ignition is switched on or the
engine is running, the brake warning
lamp; (USA only) or3 (Canada only)
in the instrument cluster comes on.
> Releasing: Depress the brake pedal.
>Pull up slightly on parking brake lever1
and press release button
2.>Push parking brake lever
1 down as far as
it will go.
When the ignition is switched on or the
engine is running, the brake warning
lamp; (USA only) or3 (Canada only)
in the instrument cluster goes out.
G
Warning!
Engaging the parking brake while the
vehicle is in motion can cause the rear
wheels to lock up. You could lose control
of the vehicle and cause an accident. In
addition, the vehicle’s brake lights do not
light up when the parking brake is
engaged.P42.20
2346
31
G
Warning!
Getting out of your vehicle with the
transmission not fully engaged in park
positionP is dangerous. When the engine
is shut off and the brakes are released,
the vehicle can be moved freely with the
gear selector lever in all positions ex

cept park position P. Also, when parked
on an incline, park positionP alone may
not prevent your vehicle from moving,
possibly hitting people or objects.
Always set the parking brake in addition
to shifting to park positionP.
When parked on an incline, always turn
the front wheels towards the road curb.

Air conditioning with climate control*
>> Controls.
151
The air conditioning improves the level of
comfort when driving at high outside
temperatures by cooling and dehumidifying
the air.Nearly all dust particles, pollutants, are
filtered out by an integrated particle filter
before outside air enters the passenger com

partment through the air distribution system.
It also operates when the air conditioning is
switched off and you have switched on the
blower.
The air conditioning only works when the
engine is running and the blower is switched
on. Maximum effectiveness is achieved if you
drive with the windows closed.
i
In warmer weather, ventilate the passen

ger compartment for a short period of time
before utilizing the air conditioning.
Switching air conditioning on/off>Make sure that the engine is running.
>Switching on: Push air volume control
1 to
level1 or higher.
>Press switch
2.
The air conditioning is switched on.
The indicator lamp on the switch comes on.
>Switching off: Press switch
2 once more.
The air conditioning is switched off.
The indicator lamp on the switch goes out.
i
The stored status is restored, if you switch
on the ignition again.
i
The air condition will be suspended tem

porarily:
• if the engine speed is too low
•when driving off
The air condition is switched off:
• at a coolant temperature of more
than 239°F (115°C)
• at outside temperatures below 38°F (3°C)
G
Warning!
Follow the recommended settings for
heating and cooling given on the following
pages. Otherwise the windows could fog
up, impairing visibility and endangering
you and others.

Engine compartment
172
>> Operation> Opening: Grasp the strap on cargo com

partment floor
1.
>Lift cargo compartment floor
1 with the
strap.
>Engage hook
4 into top mounting of cargo
compartment cover blind
5.
>Remove fastening screw
2.
>Remove engine compartment cover
3.
>Closing: Slide engine compartment cover
3
forward into the tabs provided.
>Tighten fastening screw
2.
>Disengage hook
4
from top mounting
5.
>Fold cargo compartment floor
1 back
down.
>Push the right hand and left hand cargo
compartment floor edges under the edges
of the side panels.
>Close the tailgate.
Engine oilThe amount of oil your engine needs will de

pend on a number of factors, including driving
style. Increased oil consumption can occur
when
•the vehicle is new
• the vehicle is driven at higher engine
speeds frequently
Engine oil consumption checks should only be
made after the vehicle break
in period.!
Do not use any special lubricant additives,
as these may increase wear and damage the
drive assemblies. Using special additives not
approved by smart may cause damage not
covered by the smart Limited Warranty.
More information on this subject is available
at any smart center.
G
Warning!
The engine is equipped with a transistor

ized ignition system that utilizes high
voltage. Don not touch any components
(ignition coils, spark plug sockets, diag

nostic socket) of the ignition system
• while the engine is running
• while starting the engine
• if ignition is "on" and the engine is
turned manually

What to do if ...
>> Practical hints.
237 Warning and indicator lamps in
the instrument cluster
General information:
If any of the following lamps in the instrument
cluster fails to come on during the bulb
self
check when switching on ignition
(
page 91), have the respective bulb
checked and replaced if necessary.
ABS indicator lamp (USA only)
ABS indicator lamp (Canada only)Illuminates:
• when the ignition is switched on.
Goes out:
• if engine is running or after 10 seconds• when there is a malfunction in the ABS sys

tem.
>Have the ABS system checked at an autho

rized smart center immediately.
• together with the brake warning lamp
(

page 238) when the ABS system fails.
>Stop the vehicle immediately in a safe
location.
>Do not continue to drive.
>Turn off the engine.
>Set the parking brake when leaving the
vehicle.
>Contact Roadside Assistance or an autho

rized smart center.
G
Warning!
When the ABS system is malfunctioning,
the wheels may lock during hard braking,
reducing steering capability and extend

ing the braking distance.
When the ABS is switched off due to a mal

function, the ESP
® is also switched off.
The basic driving and braking functions
are still avaiable.
The risk of your vehicle skidding is then
increased in certain situations. You
should therefore always adapt your
speed and driving style to the prevailing
road and weather conditions.

What to do if ...
238
>> Practical hints. Battery indicator lamp
Illuminates:
• when the ignition is switched on.
The indicator lamp goes out if the engine is
running.
If the Battery indicator lamp illuminates while
driving or does not go out after the engine is
started, the battery is no longer charged.
Possible causes:
• Alternator malfunctioning
• Broken poly
V
belt>Stop the vehicle immediately in a safe
location.
>Do not continue to drive.
>Turn off the engine.
>Set the parking brake when leaving the
vehicle.
>Contact Roadside Assistance or an autho

rized smart center.
!
Among other possible causes, the
poly
V
belt could be broken. Do not continue
to drive. Otherwise, the engine will overheat
due to an inoperative water pump which may
result in damage to the engine.Brake warning lamp (USA only)
Brake warning lamp (Canada only)
Illuminates:
• when the ignition is switched on.
Goes out:
• at least after 10 seconds
or
• after starting the engine.

What to do if ...
>> Practical hints.
241
Coolant temperature warning lamp
Illuminates:
• when the ignition is switched on.
The warning lamp goes out if the engine is
running.
• if the coolant is too hot.
>Stop the vehicle immediately in a safe
location.
>Do not continue to drive.
>Turn off the engine.
>Set the parking brake when leaving the
vehicle.
>Contact Roadside Assistance or an autho

rized smart center.If the coolant level has fallen below the
marking bar on the coolant reservoir
(

page 178):
>Add coolant as required.
>Have the coolant system checked for leaks
at an authorized smart center.
!
Among other possible causes, the
poly
V
belt could be broken. Do not continue
to drive. Otherwise, the engine will overheat
due to an inoperative water pump which may
result in damage to the engine.
When the system detects a malfunction,
the telltale will flash for approximately
1 minute and then remain continuously
illuminated.
This sequence will continue upon subse

quent vehicle start
ups as long as the
malfunction exists. When the malfunction
indicator is illuminated, the system may
not be able to detect or signal low tire
pressure as intended.
TPMS malfunctions may occur for a vari

ety of reasons, including the installation
of incompatible replacement or alternate
tires or wheels on the vehicle that pre

vent the TPMS from functioning properly.
Always check the TPMS malfunction tell

tale after replacing one or more tires or
wheels on your vehicle to ensure that the
replacement or alternate tires and
wheels allow the TPMS to continue to
function properly.
G
Warning!
Driving when your engine is overheated
can cause some fluids, which may have
leaked into the engine compartment, to
catch fire. You could be seriously burned.
Turn off the engine, get out of the vehicle
and do not stand near the vehicle until
the engine has cooled down.