Page 43 of 314
Steering wheel gearshift control
42
>> At a glance.
i
Model pure only:
The steering wheel in this vehicle varies from
steering wheel illustrated.
P46.10289431
Function
Page
1
Left shift paddle
1: Downshift
1 Model passion only.
133
2
Multifunction display
136
3
Right shift paddle
1: Upshift
133
Page 134 of 314
Transmission
>> Controls.
133
Steering wheel gearshift control
1
1
Left shift paddle
2
Multifunction display
3
Right shift paddleActivating manual gearshifting
>Move the gear selector lever to manual
gearshiftingM (
page 128).
Systemcontrolled automatic gearshifting
is switched off.
You can upshift or downshift through the
gears in succession.
The currently engaged gear appears in the
transmission position indicator (
page 137).
Upshifting
>Briefly push the gear selector lever for
ward in the +direction (
page 128).
or
>Pull right shift paddle
3 (page 133)
towards you.
The transmission shifts to the next higher
gear.
i
With manual gearshiftingM selected, the
transmission shifts up only to prevent engine
overreving.Downshifting
>Briefly pull the gear selector lever back
ward in the direction (
page 128).
or
>Pull left shift paddle
1 (page 133)
towards you.
The transmission shifts to the next lower
gear.
1 Model passion only.
G
Warning!
On slippery road surfaces, never down
shift in order to obtain braking action.
This could result in drive wheel slip and
reduced vehicle control. Your vehicle’s
ABS will not prevent this type of loss of
control.
Page 135 of 314
Transmission
134
>> Controls. Kickdown
You can use kickdown when you want maximum
acceleration.
>Press the accelerator past the point of
resistance.
Depending on the engine speed the
transmission shifts into a lower gear.
>When you have reached the desired speed,
briefly push the gear selector lever for
ward in the +direction (
page 128).
or
>Pull right shift paddle
3 (page 133)
towards you.
The transmission shifts to the next higher
gear.
Deactivating manual gearshifting
>Move the gear selector lever to drive
positionD (
page 128).
Systemcontrolled automatic gearshifting
is switched on again.
Emergency operation (limphome
mode)In this mode only a certain gear or a certain
gear combination can be selected. This mode
is triggered in case of transmission malfunc
tions and enables you driving to the nearest
workshop such as a smart center.
If vehicle acceleration becomes less respon
sive or sluggish or the transmission no longer
shifts, the transmission is most likely operat
ing in limphome (emergency operation)
mode. The transmission position indicator
flashes and the ¬ symbol appears in the mul
tifunction display (
page 136).
Driving in limphome mode:
>Move the gear selector lever to drive
positionD (
page 128).
>Continue to drive.
>Have the transmission checked at an autho
rized smart center as soon as possible.
i
It is possible that a gear combination in
cluding the reverse gear can not be selected.
Keep in mind when parking, that reversing the
vehicle might be impossible.
In case of a minor transmission malfunction, it
might be possible to teachin the transmis
sion in order to restore the normal transmis
sion mode.
i
If the attempt to teachin the transmission
fails, you cannot continue to drive. Therefore
we strongly recommend that you have the
transmission taughtin at a qualified work
shop or at an authorized smart center.
Teachingin the transmission system:
>Stop the vehicle in a safe location.
>Move the gear selector lever to park
positionP.
>Turn off the engine.
>Wait at least 30 seconds before restarting.
Page 136 of 314
Transmission
>> Controls.
135
>Press the brake pedal.
>Restart the engine
• Three bars instead of
appear in the
multifunction display(page 236).
>Wait at least 30 seconds.
• The transmission is taught in.
When teachingin was successful:
•
appears in the multifunction display
(page 136) again.
• Normal transmission operating is re
stored.
>Continue to drive.After an unsuccessful techin
• Three bars instead of
appear in the
multifunction display.
>Do not continue to drive.
>Turn off the engine.
>Set the parking brake when leaving the
vehicle.
>Contact Roadside Assistance or an autho
rized smart center.
Page 137 of 314
Instrument cluster
136
>> Controls.
Multifunction displayThe following displays and indicators appear
in the multifunction display:1
Status indicator with:
• Trip odometer display
• Maintenance service interval display
• Reserve fuel display
2
Main odometer display or when active
distance to next maintenance service
3
Transmission position indicator
4
Digital clock
5
Outside temperature display
6
Fuel level displayMultifunction display illumination
The multifunction display illumination comes
on when the starter switch is in position1.
It goes out after approximately 30 seconds
when the starter switch is in position0.
For adjusting the multifunction display
illumination, see "Adjusting instrument clus
ter illumination“ (
page 141).Fuel level display/reserve fuel indicator
Fuel level display
The fuel level display shows the tank's fuel
level with the aid of eight segments. The num
ber of dark segments indicates the fuel level
in the tank.
If all eight segments are dark, the tank is full. P54.32517431
G
Warning!
No messages will be displayed if either
the instrument cluster or the multifunc
tion display is inoperative.
As a result, you will not be able to see
information about your driving condi
tions, such as speed, outside tempera
ture, or warning/indicator lamps. Driving
characteristics may be impaired.
If you must continue to drive, please do
so with added caution. Visit an authorized
smart center as soon as possible.P54.32517631
Page 138 of 314
Instrument cluster
>> Controls.
137
Reserve fuel indicator
You are driving on reserve fuel if there are no
more than 1.0 US gal (3.78 l) of fuel in the
tank.
If this occurs,
• the fuel pump symbol in the fuel level
display flashes
• the reserve fuel indicator shows the fuel
level in the tank at exactly 0.1 US gal (0.5 l)
Transmission position indicator
The following information is displayed in the
transmission position indicator:
• Current gear selector lever position
• Current engaged gear (when manual
gearshifting selected)i
A flashing
in the display indicates that
the gear selector lever is in position R but the
reverse gear is not engaged. Stop the vehicle
to let the reverse gear engage.When manual gearshifting is selected:
Display
Function
Gear selector lever in park
positionP
Gear selector lever in
positionR (Reverse gear
engaged)
Gear selector lever in neutral
positionN
Gear selector lever in drive
positionD
Display
Function
First gear engaged
Second gear engaged
Third gear engaged
Fourth gear engaged
Fifth gear engaged
Page 139 of 314
Instrument cluster
138
>> Controls.
Selecting display for status
indicatorYou can select the information to be displayed
in the status indicator:
• Trip odometer display (
page 139)
• Maintenance service interval display
(
page 139)
• Reserve fuel indicator (
page 140)
1
Selecting display for status indicator/
setting the clock/activating maintenance
service interval display
2
Setting the clock/adjusting instrument
cluster illuminationDigital clock
> Activating time setting: Press right
button
2 (page 138) for approximately
five seconds.
The colon in the digital clock starts
flashing.
> Setting the time in 1 minute increments:
Press left button
1 or right button
2
(
page 138) repeatedly until the desired
time is set.>Setting the time quickly: Press left
button
1 or right button
2 (page 138)
for longer than one second.
The setting speed accelerates.
> Setting the time in 10 minute increments:
Press left button
1 or right button
2
(
page 138) for longer than five seconds.
The time is set in 10 minute increments.
>Confirm time setting: Refrain from pressing
either left button
1 or right button
2
(
page 138) for more than five seconds.
The colon in the digital clock stops flashing.
The time is set.
i
The digital clock in the multifunction
display is not synchronized with the cockpit
clock*.
P54.32517831
Page 140 of 314
Instrument cluster
>> Controls.
139
Trip odometer display
> Selecting trip odometer display: Press left
button
1 (page 138) repeatedly until the
trip odometer display appears in the status
indicator.
> Resetting trip odometer display: Press and
hold left button
1 (page 138) until the
value is set to
.Maintenance service interval display
The maintenance service interval display will
notify you approximately one month before
the next maintenance service is due.
The maintenance service interval display also
shows the type of maintenance service that is
due.
After starting the engine, the maintenance
service interval display shows this informa
tion in miles (km) or in days for approximately
ten seconds.>Start the engine.
> Selecting maintenance service interval
display: Press left button
1 (page 138)
repeatedly until the maintenance service
interval display appears in the status
indicator.
Depending on the type of maintenance
service that is due, symbol¬ or}
is dis
played.
> Clearing maintenance service interval
display: Press the left button on the
instrument cluster (
page 138).
The maintenance service interval display is
cleared.
> Activating maintenance service interval
display: Press the left button on the instru
ment cluster (
page 138) twice in quick
succession. P54.32517731
P54.32517931
