2008 SKODA SUPERB service interval reset

Instruments and Indicator/Warning Lights
10
Instruments and Indicator/Warning Lights
General view of the instrument cluster
Engine revolutions counter ⇒ page 11
Speedometer ⇒page 11
Button for display mode:
− Set hours / minutes
− Activating / deactivating the second speed in mph or km/h*
− Service interval - Display of the remaining number of days or miles to the
next Inspection Service / Reset*
1)
Coolant temperature gauge ⇒page 11
Display:
− with counter for distance driven ⇒page 12 −
with Service Interval Display ⇒page 12
− with digital clock ⇒ page 14
− with Multi-functional indicator* ⇒page 14
− with Information display* ⇒page 19
Fuel gauge ⇒page 11
Button for:
− Reset trip counter for distance driven
− Resetting Service Interval Display
− Set hours / minutes
− Activate / deactivate display mode
Fig. 2 Instrument cluster
1)Valid for countries where the values are indicated in British measuring units.
A1
A2
A3
A4
A5
A6
A7
NKO B6 20.book Page 10 Wednesday, March 26, 2008 3:15 PM

Instruments and Indicator/Warning Lights
12
An audible signal sounds as an additional warning signal.
Caution
Never run the fuel tank completely empty! An irregular fuel supply can result in
poor ignition or misfiring. Unburnt fuel may get into the exhaust system and
damage the cata lytic converter.
Note
After refuelling, the fuel gauge may drop by approx. a fraction during dynamic
driving (e.g. numerous curves, braking, up hill and downhill). When stopping the
vehicle or during less dyna mic driving, the fuel gauge indicates again the correct
fuel quantity. This occurrence is not a fault.
Counter for distance driven
The distance which you have driven with your vehicle is shown in kilometres (km).
In some countries the meas uring unit “mile” is used.
Reset button
If you hold the reset button ⇒page 10 pressed for about 1 second, the trip
counter is set back to zero. Trip counter for distance driven
The trip counter indicates the distance which you have driven
⇒fig. 3 since this
counter was last reset - in steps of 100 metres or 1/10 of a mile.
Counter for distance driven
The counter for distance driven ⇒fig. 3 indicates the total distance in kilometers or
miles which the vehicle has driven.
Fa u l t d i s p l a y
If there is a fault in the instrument cluster Error will appear as a constant text in the
display. Have the fault rectified as soon as possible by a specialist workshop.
WARNING
Never seek to adjust the trip counter for distance driven while driving for
safety reasons!
Note
If vehicles which are fitted with the inform ation display* the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the
counter for the total distance driven.
Service Interval Display
Fig. 3 Display: Counter for
distance driven
A7
Fig. 4 Service Interval
Display: Note
NKO B6 20.book Page 12 Wednesday, March 26, 2008 3:15 PM

Instruments and Indicator/Warning Lights13
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Depending on the equipment installed in th
e vehicle, the text can differ on the
display.
Service Interval Display
Before the next service interval a key symbol
 and the remaining kilometers are
indicated after switching on the ignition ⇒page 12, fig. 4 . At the same time, a
display appears regarding the remaining days until the next service interval.
The following will be displayed in the information display*:
Service in ... km or... days
The kilometre indicator or the days indica tor reduces in steps of 100 km. or days
until the service due date is reached.
A flashing key symbol
 and the text Service appears in the display for 20 seconds
as soon as the due date for the service is reached.
The following will be displayed in the information display*:
Service now!
Display regarding the distance and days until the following service interval
You can use the button to display the remaining distance driven and the days
until the next service interval ⇒ page 10.
A key symbol
 and a display regarding the remaining kilometers appear for 10
second in the display. At the same time , a display appears regarding the remaining
days until the next service interval.
On vehicles which are equipped with info rmation display*, you can call up this
information in the following menu on ⇒page 19:
„SETUP (Settings)
„Service Interval (Service)
„Info
The following will be displayed in the information display* for 10 seconds: Service in ... km or... days Resetting Service Interval Display
It is only possible to reset the Service Interval Display, if a service message or at least
a pre-warning is shown on the display of the instrument cluster.
We recommend having this resetting
performed by a specialist garage.
The specialist garage:
•resets the memory of the display after the appropriate inspection,
•makes an entry in the Service schedule,
•affix the sticker with the entry of the following service interval to the side of the
dash panel on the driver's side.
Reset the service interval displays by using the reset button ⇒page 10 on the
trip counter.
On vehicles which are equipped with info rmation display*, you can call up this
information in the following menu on ⇒page 19:
„SETTINGS
„Service Interval (Service)
„Reset
Caution
We recommend that you do not reset the Service Interval Display yourself other-
wise this can result in the service interval display being incorrectly set, which may
also result in problems with operation of your vehicle.
Note
•Never reset the display between service intervals otherwise this may result in
incorrect readouts.
•information is retained in the Service Interval Display also after the battery of
the vehicle is disconnected.
•If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interva l Display. This work is carried out by a
specialist garage.
A3
A7
NKO B6 20.book Page 13 Wednesday, March 26, 2008 3:15 PM

Instruments and Indicator/Warning Lights
14
•The data displayed is the same after resetting the display with flexible service
intervals (QG1) using the reset button as th at for a vehicle with fixed service inter-
vals (QG2). We therefore recommend having the Service Interval Display reset only
by a Škoda Service Partner who is familiar with the procedure for resetting the
display with a vehicle system tester.
•Please refer to the brochure Service schedule for extensive information about
the service intervals.
Digital clock
The time is set with the buttons and ⇒page 10, fig. 2 .
Select the display which you wish to ch ange with the button and carry out the
change with the button .
On vehicles which are fitted with informatio n display*, the setting of the time in the
menu Time (Clock) can be carried out ⇒page 23.
WARNING
The clock should not be adjusted while driving for safety reasons but only
when the vehicle is stationary!
Multi-functional indica tor (onboard computer)*
Introduction
The multi-functional indicator appears in the display ⇒page 15, fig. 5 or in the
information display ⇒page 19 depending on the equipment fitted to your vehicle.
The multi-functional indicator offers you a range of useful information. On vehicles which are fitted out with information display*, it is possible to switch
off the display of some information.
Caution
Pull out the ignition key while having cont
act with the display (for example when
cleaning) in order to prevent any damage.
Note
•In certain national versions the displays appear in the Imperial system of meas-
ures.
•If the display of the second speed is activated in mph, the current speed* is not
indicated in km/h on the display.
The outside temperature⇒ page 17
Driving time⇒page 17
Current fuel consumption⇒page 17
A3A7
A3A7
Average fuel consumption⇒page 17
Range⇒page 17
Distance driven⇒page 18
Average speed⇒page 18
Current speed*⇒page 18
Warning against excessive speeds*⇒page 18
NKO B6 20.book Page 14 Wednesday, March 26, 2008 3:15 PM

Instruments and Indicator/Warning Lights
24
Displays of the MFA
Here you can switch off or on certain displays of the multi-functional indicator.
Comfort*
You can set the following functions (depen ding on the equipment installed on the
vehicle):
Lights and Visibility
Here you can set how long the light should stay on for the function Coming/Leaving
Home and the intensity of the footwell li ghting. Furthermore you can here switch
on or off the function daylight drivin g lights and convenience turn signal. After selecting the menu
Fa c t o r y s e t t i n g the factory setting is established again.
Time
Here you can set the time, the time format (12 or 24 hour indicator) and the time
change summer/winter time.
Winter tyres
Here you can set at which speed a warning signal should sound. This function is
used for e.g winter tyres with the permissible maximum speed less than the
maximum speed of the vehicle.
When exceeding the speed, the following is displayed on the information display*:
Snow tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Language
Here you can set in which language the warning and information texts should be
displayed.
Measures
Here you can set the units for temperat ure, consumption and distance driven.
Assistant
Here you can adjust the tones of the acoustic signals of the parking aid*.
Second speed
Here you can switch on the display of the second speed in mph or in km/h
2).
Service
Here you can have the kilometers still to be driven and the days until the following
service interval shown and the Service Interval Display reset.
Factory Setting
After selecting the menu Factory Setting the factory setting of the information
display is established again.
Rain closing
On vehicles with ra in sensor you can switch on or off the
function for automatic closing of the windows and the
sliding/tilting roof in case of rain and locked vehicle. If it
is not raining and the function is set, the windows
including the sliding/tilting roof are closed automatically
after approx. 12 hours.
Door openHere you can switch on or off the functions for opening
a single door and automatic closing.
ATA c onfir mHere you can set if a signal tone should sound addition-
ally when activating or deactivating the anti-theft alarm
system .
Window op.Here you can set the convenience mode only for the
driver window or for all the windows.
Mirror downHere you can switch on or off the function for mirror
adjustment on the front pass enger side when engaging
the reverse gear .
Mirror adjust.Here you can switch on or off the function for left and
right exterior mirror adjustment simultaneously.
Factory setting
After selecting this menu the convenience setting is
reset to factory setting. The following is displayed in the
information display:
Factory setting for convenience is set
.
2)Valid for countries where the values are indicated in British measuring units.
NKO B6 20.book Page 24 Wednesday, March 26, 2008 3:15 PM