
Cockpit77
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
Main beam headlights 
This warning lamp lights up when the main beams are on.The warning lamp 
 is switched on once main beams are on or once the 
headlight flasher is operating.
Further information  ⇒page 116.
Soot accumulation in the diesel engine particulate filter 
If the indicator lights 
 you may help the filter clear itself by driving in the 
appropriate manner.
To do this, drive about 15 minutes in 4th or 5th gear (automatic gearbox: S 
gear range) at a speed of 60 km/h, with the engine running at approximately 
2000 rpm. In this way, the pollen buil d up in the filter is burned. When 
cleaning is successful, the indicator turns off.
If the indicator 
 is not deactivated, bring the vehicle to a specialised work-
shop to repair the fault.
WARNING
•
Always drive according to the road  weather conditions, the terrain and 
traffic. Driving recommendations should never lead to illegal manoeuvres 
in surrounding traffic.
•
The diesel engine particulate filter may reach extremely high tempera-
tures; it should not enter into contact with flammable materials under-
neath the vehicle. Failure to comply could result in fire.
Anti-lock brake system (ABS) 
 
A warning lamp system monitors the ABS.
The warning lamp 
 should light up for a few seconds when the ignition is 
switched on. It goes out again after th e system has run through an automatic 
test sequence.
There is a fault in the ABS if:
•
The warning lamp 
 does not light up when the ignition is switched on.
•
The warning lamp does not go out again after a few seconds.
•
The warning lamp lights up when the vehicle is moving.
The vehicle can still be braked in the normal way (except that the ABS control 
function will not function). Please take the vehicle to a qualified workshop as 
soon as possible. For further information on the ABS see the  ⇒page 183.
If a fault occurs in the ABS, the ESP* warning lamp will also light up.
Brake system fault
If the ABS warning lamp 
 lights up together with the brake warning lamp 
, this indicates not only a fault in the  ABS function, but also a possible fault 
in the brake system  ⇒.
WARNING
•
Before opening the bonnet, read and observe the warnings on 
⇒ page 213, “Working in the engine compartment”.
•
If the brake warning lamp 
 should light up together with the ABS 
warning lamp 
, stop the vehicle immediately and check the brake fluid 
level in the reservoir  ⇒page 226, “Brake fluid”. If the fluid level has 
dropped below the “MIN” mark you must not drive on. Risk of accident. 
Obtain technical assistance.
•
If the brake fluid level is correct, the fault in the brake system may have 
been caused by a failure of the ABS system. This could cause the rear 
Toledo_EN.book  Seite 77  Dienstag, 20. Januar 2009  12:58 12 

Cockpit
78wheels to lock quickly when you brake. This could cause the rear to break 
away. Risk of skidding. Stop the vehicle and seek technical assistance.Washer fluid 
This warning lamp lights up to indicate that the windscreen 
washer level is too low.This serves as a reminder to fill up the reservoir at the earliest opportunity 
⇒ page 222.
The following message is shown on the instrument panel display*
11):  REFILL 
WINDSCREEN WASHER FLUID .
Alternator 
 
This warning lamp signals a fault in the alternator.
The warning lamp 
 lights up when the ignition is switched on. It should go 
out when the engine has started running.
If the warning lamp  lights up while driving, the alternator is no longer 
charging the battery. You should immediately drive to the nearest qualified 
workshop.
You should avoid using electrical equipm ent that is not absolutely necessary 
because this will drain the battery.
Tyre p ressu
re* 
The tyre pressure control system controls the tyre speed and 
the frequency spectrum of each tyre.The tyre monitor 
12) compares wheel revolutions  and with this information, 
the diameter of each wheel using the ESP sensors. If the diameter of a wheel 
changes, the tyre monitor indicator lights  . The wheel diameter changes 
when:
•
Tyre pressure is insufficient.
•
The tyre structure is damaged.
•
The vehicle is unbalanc ed because of a load.
•
The wheels of one axle are under more  pressure (for example, driving with 
a trailer or on extreme slopes).
•
The vehicle is fitted with snow chains.
•
The emergency wheel is fitted.
11)Depending on the version of the model.WARNING (continued)
12)Depending on the model version
Fig. 49  Centre console: 
tyre monitor system 
button
Toledo_EN.book  Seite 78  Dienstag, 20. Januar 2009  12:58 12 

Cockpit79
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
•
The wheel on one axle is changed.
Tyre pressure adjustment
Following the modification to tyre pressure or after changing one or more 
wheels, the button  ⇒page 78, fig. 49  must be kept pressed while the igni-
tion is on until an acoustic signal is heard and the warning lamp goes out.
If the wheels are under excessive load (for example, driving with a trailer or 
heavy load), the tire pressure must be increased to the recommended value 
for a full load (see the sticker on the inside of the fuel flap). If the tyre monitor 
system button is pressed down, the new tyre pressures are confirmed.
The tyre pressure monitor indicator 
 lights up
If the tyre pressure of one or more wheels is much lower than the value set by 
the driver, then the tyre co ntrol warning lamp lights up  ⇒.
The tyre pressure monitor indicator  flashes
If the tyre pressure indicator flashes, this indicates a fault. Go to the nearest 
specialist workshop.
WARNING
•
When the tyre pressure indicator l ights, reduce speed immediately and 
avoid any sudden manoeuvre or braking. Stop when possible, and check 
the tyre pressure and status.
•
The driver is responsible for correct tyre pressure. For this reason, tyre 
pressure must be regularly checked.
•
Under certain circumstances (for exam ple, in a sports situation, in 
winter conditions or on a dirt track) the tyre monitor indicator may light or 
function incorrectly.Note
If the battery is disconne cted, the yellow indicator 
 lights up after turning 
the ignition on. This should  turn off after a brief journey.
Brake system* / handbrake 
 
The warning lamp lights up if the handbrake is applied, if the 
brake fluid level falls too low or if there is a fault in the brake 
system.
This warning lamp 
 lights up if
•
If the handbrake is on.
If you drive faster than 6 km/h with the handbrake on, the following message 
will appear on the instrument panel display 
13): HANDBRAKE ON.  Also, an 
audible warning is given.
•
If the brake fluid level is too low  ⇒page 226.
The instrument panel disp lays the following message
13): STOP BRAKE FLUID 
INSTRUCTION MANUAL .
•
If there is a fault in the brake system.
The instrument panel disp lays the following message
13): BRAKE SYSTEM 
FAULT INSTRUCTIONS MANUAL .
This warning lamp can light up together with the anti-lock brake system 
warning lamp.
WARNING
•
Before opening the bonnet, read and observe the warnings on 
⇒ page 213.
•
If the brake warning lamp does not  go out, or if it lights up when 
driving, the brake fluid level  ⇒page 226, “Brake fluid” in the reservoir is 
too low. Risk of accident. Stop the vehicle and do not drive on. Obtain tech-
nical assistance.
13)Depending on the version of the model.
Toledo_EN.book  Seite 79  Dienstag, 20. Januar 2009  12:58 12 

Cockpit81
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
The warning lamp should light up for a few seconds when the ignition is 
switched on. It should go out once the engine is started.
If the battery is disconnected, the indicator remains lit, even with the engine 
running. The warning light only goes of
f after a distance of approx. 50 m.
There is a fault in the electromechanica l steering system if the lamp does not 
go out or lights up whilst the vehicle is in motion. The indicator may appear 
in two different colours to indicate faults. If it lights yellow, this indicates a 
minor fault. If it lights red, seek wo rkshop assistance immediately, if no 
assistance is available stop driving. Stop the vehicle and seek technical 
assistance. The power steering does not work if the battery is flat or if the 
engine is off (for example, for towing). You should take into account that you 
will need considerably more power than  normal to steer the vehicle if the 
steering assistance is reduced or has failed completely.
For those vehicles fitted with ESP* the function “Recommended steering 
manoeuvre” is included. See  ⇒page 185.
Emission control system* 
 
This warning lamp monito rs the exhaust system.
Warning lamp 
 flashes:
When there is misfiring that can damage the catalytic converter. Reduce 
speed and drive carefully to the nearest qualified workshop to have the 
engine checked.
The instrument panel displa ys the following message
16): EXHAUST GAS SEE 
WORKSHOP . Warning lamp 
 is lit:
If a fault has developed during driving which has reduced the quality of the 
exhaust gas (e.g. lambda probe fault). Reduce speed and drive carefully to 
the nearest qualified workshop to have the engine checked.
The following information text displayed in the instrument panel display : 
EXHAUST GAS SEE WORKSHOP .
Electronic stabilisation programme (ESP)* 
 
This warning lamp monitors the electronic stabilisation 
programme.
This programme includes the ABS, EDL and TCS. This also includes the brake 
assist system (BAS), automatic cleaning of the brake discs and the trailer 
stability programme (TSP).
The warning lamp 
 has the following functions:
•
It will light for about 2 seconds when the ignition is switched on while a 
test of the function is carried out.
•
It flashes when the ESP is activated when driving.
•
It will light up continuously if there is a malfunction in the ESP.
•
It will also come on if a fault should occur in the ABS because the ESP 
operates in conjunction with the ABS.
If the ESP warning lamp 
 lights up and stays on after the engine is started, 
this may mean that the control system has temporarily switched off the ESP. 
In this case the ESP can be reactivated by switching the ignition off and then 
on again. If the warning lamp goes out,  this means the system is fully func-
tional.
If the ESP button is activated, the TCS function deactivates and the warning 
lamp flashes.
16)Depending on the version of the model.
Toledo_EN.book  Seite 81  Dienstag, 20. Januar 2009  12:58 12 

Cockpit
82Differential lock fault (EDL)*
EDL operates along with the ABS in vehicles equipped with an 
Electronic Stabilisation Program (ESP)*A malfunction in the EDL is indicated by the ABS warning lamp 
. Please 
take the vehicle to a qualified workshop as soon as possible. For further infor-
mation on the EDL  ⇒page 186, “Electronic differential lock (EDL)*”.
Traction control system (TCS)*
The traction control system prevents the driven wheels from 
spinning when the vehicle is acceleratingThe warning lamp lights up when the ignition is switched on and should turn 
out after about 2 seconds.
When the TCS is operating while drivi ng, the warning lamp flashes. If the 
system is deactivated or if there is any fault in the same, the warning lamp will 
remain lit.
It will also come on if a fault should occur in the ABS because the TCS oper-
ates in conjunction with the ABS. For further information, see  ⇒page 183, 
“Brakes”
If the TCS button is activated, the TC S function deactivates and the warning 
lamp remains lit.
By pressing again, TCS function is reactivated and the warning lamp switched 
off.
Operating the foot brake 
The footbrake must be depressed when this warning lamp lights up. This is 
necessary when the automatic gearbox*  selector lever is moved out of the 
positions  P or  N.Electronic immobiliser* “Safe”
This warning lamp flashes if an unauthorised key is used.Inside the key there is a chip that deac tivates the electronic immobiliser auto-
matically when the key is inserted into the ignition. The immobiliser will be 
activated again automatically as soon as you pull the key out of the ignition 
lock.
The instrument panel displays the following message
17):  SAFE . The vehicle 
cannot be used in that case  ⇒page 166.
The engine can, however, be started if the appropriate coded SEAT genuine 
key is used.
Note
A perfect operation of the vehicle is ensured if genuine SEAT keys are used.17)Depending on the version of the model.
Toledo_EN.book  Seite 82  Dienstag, 20. Januar 2009  12:58 12 

Lights and visibility
114A fault in the system is indicated via the flashing of the control lamp 
 on the 
instrument panel. At the same time,  a text message with information or 
instructions to perform necessary oper ations may appear on the instrument 
panel display. Take the vehicle to a qualified workshop and have the fault 
repaired.
If the control lamp 
 lights up on the instrument  panel but all the lamps are 
operating correctly  ⇒page 252, there may still be a fault in the dynamic 
curve lighting system (AFS). Take the vehicle to a qualified workshop and 
have the fault repaired.
WARNING
If the “automatic dipped  light control” is switched on, the dipped head-
lights will not be switched on in fog. They should be switched on manually 
using the light switch. The driver is personally responsible for the correct 
use of lights in all situations. “Autom atic headlight control” is merely a 
system to support the driver. Where necessary, switch on the lights manu-
ally using the light switch.Turning light* When the indicator is switched on to turn or on very tight bends, the right or 
left fog lamp automatically comes on to function as a  turning light. The 
turning light only operates if the dipped lights are on.
WARNING
If the “automatic dipped light control” is switched on, the dipped head-
lights will not be switched on in fog. They should be switched on manually 
using the light switch. The driver is personally responsible for the correct 
use of lights in all situations. “Automatic headlight control” is merely a 
system to support the dr iver. Where necessary, switch on the lights manu-
ally using the light switch.Hazard warning lights 
 
The hazard warning lights are used to draw the attention of 
other road users to your vehicle in emergencies.
If your vehicle breaks down:
1. Park your vehicle at a safe distance from moving traffic.
Fig. 76  Instrument panel: 
switch for hazard warning 
lights
Toledo_EN.book  Seite 114  Dienstag, 20. Januar 2009  12:58 12 

Lights and visibility
116Indicator and main beam headlight lever
The turn signal and main beam lever also operates the 
parking lights and the headlight flasher.The turn signal and main beam headlight lever has the following 
functions:
Switching on the turn signals
– Move the lever all the way up  ⇒page 116, fig. 77   to indicate 
right , and all the way down   to indicate  left.
Signalling a lane change
– Push the lever up   or down   to the point where you incur  resistance and then release it. The turn signal will flash several 
times. The corresponding warning lamp will also flash. Switching main beam on and off
– Turn the light switch to position 
.
–Press the lever forward ⇒ page 116, fig. 77   to switch on the 
main beams.
– Pull the lever back towards you to switch the main beam head- lights off again.
Headlight flashers
– Pull the lever towards the steering wheel   to operate the  flasher.
Switching on parking lights
– Switch the ignition off and remove the key from the lock.
– Move the lever up or down to turn the right or left-hand parking  lights on, respectively.
WARNING
The main beam can dazzle other driver s. Risk of accident! Never use the 
main beam headlights or the headligh t flasher if they could dazzle other 
drivers.
Note
•
 The turn signals  only work when the ignition is switched on. The corre-
sponding warning lamp 
 or  flashes in the instrume nt panel. The warning 
lamp 
 flashes when the turn signals are operated, provided a trailer is 
correctly attached and connected to the vehicle. If a turn signal bulb is defec-
tive, the warning lamp flashes at double  speed. If the trailer turn signal bulbs 
are damaged, warning lamp 
 does not light up. Change the bulb.
Fig. 77  Indicator and 
main beam lever
A1
A2
A1
A2
A3
A4
Toledo_EN.book  Seite 116  Dienstag, 20. Januar 2009  12:58 12 

Lights and visibility117
Safety First
Operating instructions
Practical tips
Te c h n i c a l  D a t a
•
The main beam headlights  can only be switched on if the dipped beam 
headlights are already on. The warning lamp 
 then comes on in the combi-
instrument.
•
The  headlight flasher  comes on for as long as you pull the lever – even if 
no other lights are switched on. The warning lamp 
 then comes on in the 
combi-instrument.
•
When the  parking lights are switched on, the headlight and the rear light 
on the corresponding side of the vehicle  light up. The parking lights will only 
work if the key is removed from the ignition. If the lights are switched on, a 
buzzer  gives an audible warning while the driver door is open.
•
If the turn signal lever is left on after the key has been taken out of the 
ignition lock, an acoustic signal sounds  when the driver door is opened. This 
is a reminder to switch off the turn signal, unless of course you wish to leave 
the parking light on.
Interior lightsFront interior light type 1The switch    ⇒fig. 78  is used to select the following positions:
Courtesy light position 
Rocker switch in flat position (not ac tivated). The interior lights are automat-
ically switched on when the vehicle is unlocked or the key removed from the 
ignition lock And turn off approx. 20 seconds after closing the doors. The inte-
rior lights are switched off when the vehi cle is locked or when the ignition is 
switched on.
Interior light switched on 
Push the switch to the position 
.
Interior light switched off O
Push the switch to position O  ⇒fig. 78 .
Fig. 78  Interior roof trim: 
front interior lights
AA
Toledo_EN.book  Seite 117  Dienstag, 20. Januar 2009  12:58 12