2008 Seat Altea Owner's Manual

If and when255
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Xenon headlights
21)/ self-adjusting*
Dipped and full beam - D1S
22)
Flashes and extra full beam - H1
Position W5W
Turn signals PY21W
Fog lights
Fog lights - H3
Upper rear light
Stop/Position - P21W
23)
Turn signals - R10W
Lower rear light
Fog light - P21W
Reverse light - P21W
Side indicator
Side indicator - W5W
Registration plate light
Registration plate light - C5W
Note
•
Due to the difficulty in accessing the lamps, any replacement work should
be done by a SEAT dealer. However, the following is a description of how to
change the lamps except for the fog lights* and interior lamps.
Main headlight lamps
Turn signals
Dipped headlights
Main beam headlights
Side lights
21)On this type of headlight, the bulb changes must be made by the SEAT dealer, given
that complex elements must be removed from the vehicle and a reset must be made
on the automatic control system incorporated.22)The Xenon bulbs discharge 2.5 times the light flux and have an average lifespan of 5
times more than that of halogen bulbs, this means that, except due to unusual circum-
stances, there is no need to change the bulbs for the whole life of the vehicle.23)Electronically controlled single filament bulb for Stop/side bulbs. If the bulb blows it
will not work in either position or Stop.
Fig. 182 Main headlight
lamps
AAABACAD
altea ingles.book Seite 255 Dienstag, 11. September 2007 4:39 16

If and when
256Tu r n si g nal l a m ps– Raise the bonnet.
– Rotate the lamp holder ⇒fig. 183 to the left and pull.
– Remove the bulb by pressing on the lamp holder and rotating at the same time to the left.
– Installation is done in the reverse order.
Dipped beam lights–Raise the bonnet
Fig. 183 Turn signal
lamps
AA
Fig. 184 Dipped head-
lightsFig. 185 Dipped head-
lights
altea ingles.book Seite 256 Dienstag, 11. September 2007 4:39 16

If and when257
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
– Remove the loops ⇒page 256, fig. 184 in the direction of
the arrow and remove the cover.
– Remove the connector ⇒page 256, fig. 185 from the bulb.
– Disengage the retainer spring ⇒ page 256, fig. 185 pressing
inwards and to the right.
– Extract the bulb and fit the replacement so that the rim of the attachment plate is on the reflector cut-out.Main beam lights
– Raise the bonnet
– Remove the cover ⇒fig. 186 by pulling on this.
– Remove the connector ⇒fig. 187 from the bulb.
– Press the spring ⇒fig. 187 inwards and to the right.
– Extract the bulb and fit the replacement so that it sits correctly into the cut-out on the reflector.
– Installation is done in the reverse order.
A1
A2
A3
Fig. 186 Main beam
headlights
Fig. 187 Main beam
headlights
AC
A1
A2
altea ingles.book Seite 257 Dienstag, 11. September 2007 4:39 16

If and when
258Side lights– Raise the bonnet.
– Remove the cover ⇒fig. 188 by pulling on this. – Extract the lamp holder
⇒fig. 189 outwards.
– Replace the bulb by pulling this out and inserting the replace- ment.
– Installation is done in the reverse order.
Rear lights•
Side lights
•
Brake lights
•
Turn signals
•
Reversing lights
•
Rear fog light
Fig. 188 Side lightsFig. 189 Side lights
AD
A1
altea ingles.book Seite 258 Dienstag, 11. September 2007 4:39 16

If and when259
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side lights and brake lights– Open the tailgate
– Remove the bolts ⇒fig. 190 . – Remove the cover of the luggage compartment lateral panel.
– Unscrew the plastic fitting
⇒fig. 191 securing the rear light.
Inserting a screwdriver under the plastic fitting may help to
loosen it.
– Partially remove the rear light from its casing taking care not to pull on the cable.
– Remove the lamp holder connector.
– Unscrew the bolts ⇒page 260, fig. 192 from the lamp holder
and pull on this.
– Press on the lamp and rotate to the left then fit the replacement.
– To refit follow the steps in reverse order, taking special care when fitting the lamp holder. The metal contacts of the lamp holder
ends should be correctly fitted with respect to the rear light
contacts.
Fig. 190 Side lights and
brake lightsFig. 191 Side lights and
brake lights
AA
ABAC
altea ingles.book Seite 259 Dienstag, 11. September 2007 4:39 16

If and when
260Tu r n i n d i ca to rs– Remove the diode from its housing ⇒ page 259.– Unscrew the bolts ⇒
fig. 192 from the lamp holder and pull
on this.
– Pull out the lamp holder from the turn signal using a screw driver in the direction of the arrow (see ⇒fig. 193).
– Fit the replacement lamp by pressing it down and rotating to the left.
– Installation is done in the reverse order.
Reverse light / rear fog light– Rotate the lamp holder to the left, and remove it in the direction of the arrow ⇒fig. 194.
– Replace the bulb by pressing on it and rotating at the same time to the left
Fig. 192 Indicator lightsFig. 193 Indicator lights.
AC
Fig. 194 Lamp on interior
side of bumper
altea ingles.book Seite 260 Dienstag, 11. September 2007 4:39 16

If and when261
Safety First
Operating instructions
Tips and Maintenance
Te c h n i c a l D a t a
Side indicators– Press the indicator to the left or to the right to remove the lamp.
– Remove the lamp holder from the indicator.
– Remove the failed glass bulb and replace with a new bulb.
– Insert the lamp holder in the indicator guide until it clicks into
place.
– First place the indicator in the opening in the bodywork, fixing the tabs ⇒fig. 195 , arrow .
– Insert the lamp as shown by the arrow ⇒fig. 195.
Luggage compartment lights– Extract the tulip shaped fitting by pressing on the inside edge of
this -arrow- using the flat side of a screwdriver ⇒fig. 196 .
Fig. 195 Side indicator
A1
A2
Fig. 196 Luggage
compartment lightFig. 197 Luggage
compartment light
altea ingles.book Seite 261 Dienstag, 11. September 2007 4:39 16

If and when
262
– Press the lamp sideways and remove it from its housing ⇒page 261, fig. 197 .Registration light
– Remove the tulip-shaped fitting, carefully using the flat side of
the screwdriver as a lever inserted in the crack as shown by the
arrow ⇒fig. 198.
– Remove the lamp, moving it in the direction of the arrow and outwards ⇒fig. 199 .
Fig. 198 Registration
plate light
Fig. 199 Registration
plate light
altea ingles.book Seite 262 Dienstag, 11. September 2007 4:39 16