To change the current air delivery mode, use the right
knob to select one of the following:
H(Vent):This mode directs air to the instrument
panel outlets.
)(Bi-Level):This mode divides the air between the
instrument panel outlets and the oor outlets.
6(Floor):This mode directs most of the air to the
oor outlets with some air directed to the windshield.
When this mode is selected, the system turns the
recirculation mode off. Recirculation mode cannot be
selected while in oor mode. This is to help prevent
window fogging.
The right knob can also be used to select defog or
defrost mode. See “Defogging and Defrosting” later in
this section.
#(Normal Air Conditioning):Press this button to
turn the air conditioning system on or off. When this
button is pressed, an indicator light comes on to show
that the air conditioning is activated. Normal Air
Conditioning (A/C) can be selected in any mode as long
as the fan is on and the outside air temperature is above
freezing. Normal A/C cannot be selected at the same
time as Hybrid Air Conditioning (A/C). A ashing indicator
light indicates that the air conditioning compressor is
currently not available.When Normal A/C is selected, the climate control system
will prevent all automatic engine start/stop operations.
This will ensure the cabin comfort is maintained. See “Air
Conditioning and Automatic Engine Start/Stop” later in
this section.
N(Hybrid Air Conditioning):Press this button to
turn the Hybrid A/C system on or off. When this button is
pressed, an indicator light comes on to show that the
Hybrid A/C is activated. Hybrid A/C can be selected in
any mode, except defrost as long as the fan is on and the
outside air temperature is above freezing. Hybrid A/C
cannot be selected at the same time as the normal air
conditioning. A ashing indicator light indicates the air
conditioning compressor is not available.
The Hybrid A/C works to balance fuel economy and air
conditioning comfort. When Hybrid A/C is used in warm
weather, the vehicle gets better fuel economy by allowing
more frequent start/stops. For additional cooling, select
Normal A/C. See “Air Conditioning and Automatic Engine
Start/Stop” later in this section.
3-20
ProCarManuals.com
Speedometer and Odometer
The speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h).
The odometer shows how far your vehicle has been
driven, in either miles or kilometers.
Your vehicle has a tamper-resistant odometer. If your
vehicle needs a new odometer installed, the new one will
be set to the mileage total of the old odometer. If this is
not possible, it will be set at zero and a label must be
put on the driver’s door to show the old mileage reading
when the new odometer was installed. If the mileage
is unknown, the label should then indicate “previous
mileage unknown”.
Trip Odometer
Your trip odometer is located on the instrument panel
and shows how far your vehicle has been driven since the
trip odometer was last reset. To reset the trip odometer
to zero, press and hold the trip/reset button on the
speedometer for about two seconds. Press the trip/reset
button to switch between the trip odometer and odometer.
Tachometer
The tachometer
displays the engine
speed in revolutions
per minute (rpm).
The auto stop indicator is located at the bottom of the
tachometer. For more information seeAuto Stop Mode
on page 3-42. U.S. shown,
Canada similar
3-27
ProCarManuals.com
If the tire pressure display shows dashes instead of a
value, there may be a problem with your vehicle. If this
consistently occurs, see your dealer/retailer for service.
HOLD STEM TO RELEARN REMOTE KEY
This display matches Remote Keyless Entry (RKE)
transmitters to your vehicle. To match a transmitter:
1. Put the vehicle in PARK (P).
2. Press and release the reset stem until HOLD STEM
TO RELEARN REMOTE KEY displays.
3. Press and hold the reset stem until REMOTE KEY
LEARNING ACTIVE is displayed.
4. Press and hold the lock and unlock buttons on
the rst transmitter at the same time for about
15 seconds.
A chime will sound indicating that the transmitter
is matched and REMOTE KEY LEARNING
COMPLETE will be displayed.
5. To match additional transmitters at this time, repeat
Step 4.
Each vehicle can have a maximum of
eight transmitters matched to it.
6. To exit the programming mode, cycle the key to
LOCK/OFF.
HOLD STEM TO SET ECO (Economy)
Press and release the reset stem until HOLD STEM TO
SET ECO (Economy) displays. The HOLD STEM TO
SET ECO display will only be available when the vehicle
is in PARK (P). This display turns the fuel economy light
on or off. Once in this display, press the reset stem to
select ON (default) or OFF. SeeFuel Economy Light on
page 3-43for more information.
HOLD STEM TO CALIBRATE COMPASS
Press and release the reset stem until HOLD STEM TO
CALIBRATE COMPASS displays. The compass can
be manually calibrated. To calibrate the compass
through the DIC, seeDIC Compass on page 3-48.
HOLD STEM TO SET COMPASS ZONE
Press and release the reset stem until HOLD STEM
TO SET COMPASS ZONE displays. To change
the compass zone through the DIC, seeDIC Compass
on page 3-48.
3-47
ProCarManuals.com
Setting the Tone
(Bass/Midrange/Treble)
BASS/MID/TREB (Bass, Midrange, or Treble):To
adjust bass, midrange, or treble, press the
fknob until
the tone control labels display. Continue pressing to
highlight the desired label, or press the pushbutton
positioned under the desired label. Turn the
fknob
clockwise or counterclockwise to adjust the highlighted
setting. You can also adjust the highlighted setting
by pressing either SEEK arrow,
\FWD (forward),
or
sREV (reverse) button until the desired levels are
obtained. If a station’s frequency is weak, or has static,
decrease the treble.
To quickly adjust bass, midrange, or treble to the middle
position, press the pushbutton positioned under the
BASS, MID, or TREB label for more than two seconds.
A beep sounds and the level adjusts to the middle
position.
To quickly adjust all tone and speaker controls to
the middle position, press the
fknob for more than
two seconds until a beep sounds.EQ (Equalization):Press to select preset equalization
settings.
To return to the manual mode, press the EQ button until
Manual displays or manually adjust the bass, midrange,
or treble by pressing the
fknob.
Adjusting the Speakers (Balance/Fade)
BAL/FADE (Balance/Fade):To adjust balance or
fade, press the tune knob until the speaker control labels
display. Continue pressing to highlight the desired label,
or press the pushbutton positioned under the desired
label. Turn the
fknob clockwise or counterclockwise
to adjust the highlighted setting. The highlighted setting
can also be adjusted by pressing either SEEK arrow,
\FWD, orsREV button until the desired levels
are obtained.
To quickly adjust balance or fade to the middle position,
press the pushbutton positioned under the BAL or FADE
label for more than two seconds. A beep sounds and the
level adjusts to the middle position.
To quickly adjust all speaker and tone controls to the
middle position, press the
fknob for more than
two seconds until a beep sounds.
3-64
ProCarManuals.com