2008 SATURN OUTLOOK Owners Manual

To access the third row:
1. Remove objects on the oor in front of or on the
second row seat, or in the seat tracks on the oor.
2. Move the front center console armrest completely
forward. SeeCenter Console Storage on page 2-56
3. Place folding armrests in the upright position.
4. The safety belt must be unfastened and in the
stowed position.
5. Pull the sliding seat lever (C) forward and move the
seatback forward. The seat cushion will fold, and
the entire seat will slide forward.Returning the Seat to the Seating
Position
To return the second row seat to its normal seating
position:
1. Remove objects on the oor behind the second row
seat, or in the seat tracks on the oor.
2. Pull the seatback rearward until it is locked in place.
3. Slide the seat rearward by pushing on the
seatback until it is locked into place.
4. Push down on the rear of the seat cushion until it is
locked in place.
5. Push and pull on the seatback and seat cushion to
make sure they are locked in place
6. Check that the safety belt is not under the seat
cushion.
Reclining the Seatbacks
To recline the seatback:
1. Leaning forward in the seat, pull the reclining
seatback strap (B).
2. Move the seatback to the desired position, then
release the strap to lock the seatback in place.
3. Push and pull on the seatback to make sure it is
locked.
1-13
ProCarManuals.com

Folding the Rear Seat
To fold the second row seats:
1. Remove anything on or under the seat.
2. Place the armrest in the upright position, and
unfasten the safety belt.
3. Pull forward on the reclining seatback strap (B) and
push down on the seatback.
4. If the headrest hits the front seat, slide the second
row seat rearward.
To return the seatback to the seating position, lift the
upper corner of the seatback and push it rearward until
it locks into place. Push and pull on the seatback to
make sure it is locked.
Adjusting the Seats
To adjust the second row seats, pull outward on the
seat adjustment handle (A). Slide the seat forward or
rearward to the desired position. Release the handle
and push and pull on the seat to make sure it is locked.
Third Row Seats
{CAUTION:
Using the third row seating position while the
second row is folded, or pushed forward in the
entry position, could cause injury in a sudden
stop or crash. Be sure to return the seat to the
passenger seating position. Push and pull on
the seat to make sure it is locked into place.
The third row seats can be folded forward or removed.
Notice:Folding a rear seat with the safety belts
still fastened may cause damage to the seat or
the safety belts. Always unbuckle the safety belts
and return them to their normal stowed position
before folding a rear seat.
1-14
ProCarManuals.com

To fold the seatback:
1. Remove anything on or under the seat.
2. Disconnect the rear safety belt mini-latch, using
a key in the slot on the mini-buckle, let the belt
retract into the headliner. Stow the mini-latch in
the holder located in the headliner.3. Pull up on the release
lever located on the
back of the seat.
The headrest moves
forward automatically.
4. Push the seatback forward to lay at.
1-15
ProCarManuals.com

To return the seatback to the seating position:
1. Raise the seatback into place by using the pullstrap
from the rear of the vehicle, or by pushing it into
place from inside the vehicle.
2. The headrest must be locked into place before
sitting in the seat.
{CAUTION:
If the seatback is not locked, it could move
forward in a sudden stop or crash. That could
cause injury to the person sitting there. Always
push and pull on the seatback to be sure it is
locked.
3. Push and pull on the seatback to make sure it is
locked in place.
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not provide
the protection needed in a crash. The person
wearing the belt could be seriously injured.
After raising the rear seatback, always check
to be sure that the safety belts are properly
routed and attached, and are not twisted.
4. Reconnect the center safety belt mini-latch to the
mini-buckle. Do not let it twist.
5. Pull on the safety belt to be sure the mini-latch is
secure.
1-16
ProCarManuals.com

Removing the Third Row Seats
1. Remove the cargo management system, if it is in
the vehicle. SeeCargo Management System on
page 2-59.
2. Remove anything on or under the seat.
Notice:Folding a rear seat with the safety belts
still fastened may cause damage to the seat or the
safety belts. Always unbuckle the safety belts
and return them to their normal stowed position
before folding a rear seat.
3. Fold the seatback down. See “Folding the Seatback”
earlier in this section.
4. Remove the rear bolts located on the oor on each
side of the seat.
5. Remove the seat by tilting it slightly upward, and
then pulling it out of the rear of the vehicle in one
motion.
6. Put the bolts back into the holes on the oor so
they do not get misplaced.
Installing the Third Row Seats
1. Before installing the seat the seatback must be
folded forward. See “Folding the Seatback”
earlier in this section.
The seats must be placed in the proper locations
for the legs to attach correctly. The wider seat must
be installed on the driver side and the narrower
seat on the passenger side. Remove the bolts from
the holes in the oor before installing the seats.
2. Place the seat on the vehicle oor so that the front
seat hooks are on the vehicle bars.
3. Reinstall the bolts, and torque to 55Y(41 lb ft).
Pull up on the seat to make sure it is locked in place.
4. Raise the seatback to its upright position. Push
and pull on the seatback to make sure it is locked
into place.
5. Push the headrest up into position. Push and
pull on the headrest to make sure it is locked
into place.
6. Reconnect the center safety belt mini-latch to the
mini-buckle. Do not let it twist.
1-17
ProCarManuals.com

Safety Belts
Safety Belts: They Are for Everyone
This section of the manual describes how to use
safety belts properly. It also describes some things not
to do with safety belts.
{CAUTION:
Do not let anyone ride where he or she cannot
wear a safety belt properly. If you are in a crash
and you are not wearing a safety belt, your
injuries can be much worse. You can hit things
inside the vehicle harder or be ejected from it
and be seriously injured or killed. In the same
crash, you might not be, if you are buckled up.
Always fasten your safety belt, and check that
your passenger(s) are restrained properly too.
{CAUTION:
It is extremely dangerous to ride in a cargo
area, inside or outside of a vehicle. In a
collision, people riding in these areas are more
likely to be seriously injured or killed. Do not
allow people to ride in any area of your vehicle
that is not equipped with seats and safety belts.
Be sure everyone in your vehicle is in a seat and
using a safety belt properly.
This vehicle has indicators as a reminder to buckle the
safety belts. SeeSafety Belt Reminders on page 3-39
for additional information.
1-18
ProCarManuals.com

In most states and in all Canadian provinces, the law
requires wearing safety belts. Here is why:
You never know if you will be in a crash. If you do have
a crash, you do not know if it will be a serious one.
A few crashes are mild, and some crashes can be so
serious that even buckled up, a person would not survive.
But most crashes are in between. In many of them,
people who buckle up can survive and sometimes walk
away. Without safety belts, they could have been badly
hurt or killed.
After more than 40 years of safety belts in vehicles,
the facts are clear. In most crashes buckling up does
matter... a lot!Why Safety Belts Work
When you ride in or on anything, you go as fast as
it goes.
Take the simplest vehicle. Suppose it is just a seat
on wheels.
1-19
ProCarManuals.com

Put someone on it. Get it up to speed. Then stop the vehicle. The rider
does not stop.
1-20
ProCarManuals.com