2008 SATURN ASTRA wheel bolts

Rear disc brake pads do not have
built-in brake pad wear indicators.
Periodic visual inspection of the rear
brake pads is required to determine
when to replace the pads. Visually
inspect the rear brake pads
whenever the rear wheels are
removed such as during tire rotation.
1. Set the parking brake and make
sure that the brakes have been
given enough time to cool.
2. Remove the rear wheels.
3. Visually inspect the rear brake
inner pads (C) at each rear
wheel through the inspection
window in the brake caliper (A).Brake pads should be replaced
when the inner pad (C) is
worn to 5/64 in (2 mm) of pad
thickness (B). New brake
pads, with no wear, are 25/64 of
an inch (10 mm) thick.
4. After brake pad inspection or
replacement, install the rear
wheels.Some driving conditions or climates
can cause a brake squeal when
the brakes are rst applied or lightly
applied. This does not mean
something is wrong with the brakes.
Properly torqued wheel bolts are
necessary to help prevent brake
pulsation. When tires are rotated,
inspect brake pads for wear and
evenly tighten wheel bolts in
the proper sequence to torque
specications inCapacities
and Specifications on page 10-2.
Brake linings should always
be replaced as complete axle sets.
Brake Pedal Travel
See your dealer/retailer if the brake
pedal does not return to normal
height, or if there is a rapid increase
in pedal travel. This could be a sign
that brake service might be required.
Brake Adjustment
Every time you make a brake stop,
the disc brakes adjust for wear.
9-24 Vehicle Service and Care
ProCarManuals.com

Use this pattern when rotating
the vehicle tires. Do not include
the compact spare tire in the
tire rotation.
{CAUTION
Rust or dirt on a wheel, or
on the parts to which it is
fastened, can make wheel
bolts become loose after
time. The wheel could come
off and cause a crash. When
you change a wheel, remove
any rust or dirt from places
where the wheel attaches to
the vehicle using a scraper
or wire brush.
Installing wheels with a good
metal-to-metal contact at
the mounting surfaces is
necessary to prevent wheel
bolts from becoming loose.To prevent corrosion or rust
build-up, lightly coat the wheel
hub center and the cone-shaped
surface of each wheel bolt
with wheel bearing grease,
after a wheel change.
SeeChanging a Flat Tire on
page 9-60for information
on installing the tire and wheel
assembly. Also see “Wheel
Bolt Torque” underCapacities
and Specifications on page 10-2.
Adjust the front and rear tires to
the recommended cold tire
ination pressure shown on the
Tire and Loading Information
label. SeeInflation - Tire
Pressure on page 9-46and
Loading the Vehicle on
page 8-30.
9-52 Vehicle Service and Care
ProCarManuals.com

Wheel Alignment and
Tire Balance
The tires and wheels on your
vehicle were aligned and balanced
carefully at the factory to give
you the longest tire life and best
overall performance. Adjustments to
wheel alignment and tire balancing
will not be necessary on a regular
basis. However, if you notice
unusual tire wear or your vehicle
pulling to one side or the other,
the alignment might need to
be checked. If you notice your
vehicle vibrating when driving on a
smooth road, the tires and wheels
might need to be rebalanced.
See your dealer/retailer for proper
diagnosis.
Wheel Replacement
Replace any wheel that is bent,
cracked or badly rusted or corroded.
If the wheel bolts keep coming
loose, the wheel and wheel bolts
should be replaced. If the wheel
leaks air, replace it (except some
aluminum wheels, which can
sometimes be repaired). See your
dealer/retailer if any of these
conditions exist.
Your dealer/retailer will know the
kind of wheel you need.
Each new wheel should have the
same load-carrying capacity,
diameter, width, offset and be
mounted the same way as the one
it replaces.If you need to replace any of the
wheels or wheel bolts, replace
them only with new GM original
equipment parts. This way, you will
be sure to have the right wheel
and wheel bolts for the vehicle.
{CAUTION
Using the wrong replacement
wheels or wheel bolts on your
vehicle can be dangerous.
It could affect the braking and
handling of the vehicle, make
the tires lose air and make you
lose control of the vehicle. You
could have a collision in which
you or others could be injured.
Always use the correct wheel
and wheel bolts for replacement.
9-58 Vehicle Service and Care
ProCarManuals.com

5. The jack and tools are stored
below the spare tire.
6. The tools you will be using
include the jack (A), wheel
wrench (B) and jack handle (C).
Removing the Flat Tire
and Installing the
Spare Tire
1. If your vehicle has wheel covers,
remove the cover.
Do not try to put a wheel cover
on your compact spare tire. It will
not t. Store the wheel cover
in the trunk until you have the at
tire repaired or replaced.
Notice:Wheel covers will not t
on your vehicle’s compact spare.
If you try to put a wheel cover on
the compact spare, the cover or
the spare could be damaged.
2. If your vehicle has wheel bolt
caps, remove the caps. Store
the caps with the wheel cover.3. Use the wheel wrench to loosen
all the wheel bolts. Do not
remove them yet.
9-62 Vehicle Service and Care
ProCarManuals.com

6. Raise the vehicle by turning the
jack handle clockwise. Raise the
vehicle far enough off the
ground so there is enough room
for the compact spare tire to
t under the vehicle.
7. Remove all of the wheel bolts.
{CAUTION
Rust or dirt on a wheel, or on
the parts to which it is
fastened, can make wheel bolts
become loose after time. The
wheel could come off and
cause an accident. When you
change a wheel, remove any
rust or dirt from places where
the wheel attaches to the
vehicle. In an emergency, you
can use a cloth or a paper
towel to do this; but be sure to
use a scraper or wire brush
later, if needed, to get all the
rust or dirt off. SeeChanging a
Flat Tire on page 9-60.8. Remove any rust or dirt from the
wheel bolts, mounting surfaces
and spare wheel.
Installing wheels with a good
metal-to-metal contact at
the mounting surface is
necessary to prevent the wheel
bolts from becoming loose.
To prevent corrosion or rust
build-up, apply a light coat of
wheel bearing grease to the
wheel hub center and to the
cone-shaped surface of each
wheel bolt at every wheel change.
9-64 Vehicle Service and Care
ProCarManuals.com

9. Place the compact spare tire on
the wheel-mounting surface.
10. Reinstall the wheel bolts with
the rounded end of the bolts
toward the wheel. Tighten each
bolt by hand until the wheel
is held against the hub.
11. Lower the vehicle by turning the
jack handle counterclockwise.
Lower the jack completely.12. Tighten the wheel bolts rmly
in a crisscross sequence,
as shown.
{CAUTION
Incorrect or improperly
tightened wheel bolts can
cause the wheel to come loose
and even come off. This could
lead to a crash. If you have to
(Continued)
CAUTION (Continued)
replace them, be sure to get
new original equipment wheel
bolts. Stop somewhere as
soon as you can and have the
bolts tightened with a torque
wrench to the proper torque
specication. SeeCapacities
and Specifications on
page 10-2for wheel bolt
torque specication.
Notice:Improperly tightened
wheel bolts can lead to brake
pulsation and rotor damage.
To avoid expensive brake repairs,
evenly tighten the wheel bolts
in the proper sequence and to
the proper torque specication.
SeeCapacities and Specifications
on page 10-2for the wheel bolt
torque specication.
Vehicle Service and Care 9-65
ProCarManuals.com