2008 SATURN ASTRA tow

Buying New Tires.............9-54
Different Size Tires
and Wheels.....................9-55
Uniform Tire Quality
Grading...........................9-56
Wheel Alignment and
Tire Balance....................9-58
Wheel Replacement..........9-58
Tire Chains.......................9-59
Tire Changing
If a Tire Goes Flat............9-60
Changing a Flat Tire.........9-60
Removing the Spare
Tire and Tools.................9-61
Removing the Flat Tire
and Installing the
Spare Tire
.......................9-62
Storing a Flat or Spare
Tire and Tools.................9-66
Compact Spare Tire..........9-67
Jump Starting
Jump Starting...................9-68
Towing
Towing Your Vehicle.........9-72
Recreational Vehicle
Towing............................9-72
Towing a Trailer................9-72
Appearance Care
Interior Cleaning................9-72
Exterior Cleaning..............9-75
Sheet Metal Damage........9-78
Finish Damage..................9-79
Underbody Maintenance. . . .9-79
Chemical Paint Spotting. . . .9-79
Vehicle Care/Appearance
Materials.........................9-80
Service
For service and parts needs,
visit your dealer/retailer. You will
receive genuine Saturn parts
and Saturn-trained and supported
service people.
Genuine Saturn parts have one of
these marks.
9-2 Vehicle Service and Care
ProCarManuals.com

A.Engine Air Cleaner/Filter on
page 9-11.
B. Engine Oil Fill Cap.Engine Oil
on page 9-7.
C. Brake Fluid Reservoir.Brakes
on page 9-22.
D. Coolant Reservoir.Cooling
System on page 9-16.
E. Coolant Reservoir Pressure Cap.
Pressure Cap on page 9-15.
F.Engine Compartment Fuse Block
on page 9-34.
G.Battery on page 9-25.
H.Windshield Washer Fluid on
page 9-20.
I. Engine Oil Dipstick.Engine Oil
on page 9-7.Engine Oil
If the low oil level light appears on
the instrument cluster, check
the engine oil level right away.
SeeLow Oil Level Light on
page 4-23. You should check the
engine oil level regularly; this is just
a reminder.
Checking Engine Oil
It is a good idea to check the
engine oil every time you get fuel.
In order to get an accurate reading,
the oil must be warm and the
vehicle must be on level ground.
The engine oil dipstick handle
is a yellow loop. SeeEngine
Compartment Overview on page 9-6
for the location of the engine oil
dipstick.
1. Turn off the engine and give the
oil several minutes to drain back
into the oil pan. If you do not
do this, the oil dipstick might not
show the actual level.
2. Pull the dipstick and clean it with
a paper towel or cloth, then push
it back in all the way. Remove it
again, keeping the tip down
and check the level.
Vehicle Service and Care 9-7
ProCarManuals.com

License Plate Lamp
To replace one of these bulbs:
1. Push tab in and pull down on it to
remove the license plate lamp.2. Turn and pull the license plate
lamp toward you through the
opening.3. Turn the bulb socket
counterclockwise and pull the
bulb straight out of the socket.
4. Install the new bulb.
5. Reverse Steps 1 through 3 to
reinstall the license plate lamp.
9-32 Vehicle Service and Care
ProCarManuals.com

Tire Changing
If a Tire Goes Flat
It is unusual for a tire to blowout
while you are driving, especially if
you maintain your vehicle’s tires
properly. If air goes out of a tire, it is
much more likely to leak out slowly.
But if you should ever have a
blowout, here are a few tips about
what to expect and what to do:
If a front tire fails, the at tire creates
a drag that pulls the vehicle toward
that side. Take your foot off the
accelerator pedal and grip the
steering wheel rmly. Steer to
maintain lane position, and then
gently brake to a stop well out of the
traffic lane.
A rear blowout, particularly on a
curve, acts much like a skid and
may require the same correction you
would use in a skid. In any rear
blowout remove your foot from the
accelerator pedal. Get the vehicle
under control by steering theway you want the vehicle to go.
It may be very bumpy and noisy, but
you can still steer. Gently brake to
a stop, well off the road if possible.
{CAUTION
Lifting a vehicle and getting
under it to do maintenance or
repairs is dangerous without the
appropriate safety equipment
and training. The jack provided
with your vehicle is designed
only for changing a at tire. If it
is used for anything else, you or
others could be badly injured or
killed if the vehicle slips off the
jack. Use the jack provided with
your vehicle only for changing a
at tire.
If a tire goes at, the next part
shows how to use the jacking
equipment to change a at tire
safely.
Changing a Flat Tire
If a tire goes at, avoid further tire
and wheel damage by driving slowly
to a level place. Turn on the
hazard warning ashers.
{CAUTION
Changing a tire can be
dangerous. The vehicle can slip
off the jack and roll over or fall
on you or other people. You and
they could be badly injured or
even killed. Find a level place
to change your tire. To help
prevent the vehicle from
moving:
1. Set the parking brake
rmly.
2. Put an automatic
transmission shift lever in
P (Park), or shift a manual
transmission to 1 (First) or
R (Reverse).
(Continued)
9-60 Vehicle Service and Care
ProCarManuals.com

6. Raise the vehicle by turning the
jack handle clockwise. Raise the
vehicle far enough off the
ground so there is enough room
for the compact spare tire to
t under the vehicle.
7. Remove all of the wheel bolts.
{CAUTION
Rust or dirt on a wheel, or on
the parts to which it is
fastened, can make wheel bolts
become loose after time. The
wheel could come off and
cause an accident. When you
change a wheel, remove any
rust or dirt from places where
the wheel attaches to the
vehicle. In an emergency, you
can use a cloth or a paper
towel to do this; but be sure to
use a scraper or wire brush
later, if needed, to get all the
rust or dirt off. SeeChanging a
Flat Tire on page 9-60.8. Remove any rust or dirt from the
wheel bolts, mounting surfaces
and spare wheel.
Installing wheels with a good
metal-to-metal contact at
the mounting surface is
necessary to prevent the wheel
bolts from becoming loose.
To prevent corrosion or rust
build-up, apply a light coat of
wheel bearing grease to the
wheel hub center and to the
cone-shaped surface of each
wheel bolt at every wheel change.
9-64 Vehicle Service and Care
ProCarManuals.com

9. Place the compact spare tire on
the wheel-mounting surface.
10. Reinstall the wheel bolts with
the rounded end of the bolts
toward the wheel. Tighten each
bolt by hand until the wheel
is held against the hub.
11. Lower the vehicle by turning the
jack handle counterclockwise.
Lower the jack completely.12. Tighten the wheel bolts rmly
in a crisscross sequence,
as shown.
{CAUTION
Incorrect or improperly
tightened wheel bolts can
cause the wheel to come loose
and even come off. This could
lead to a crash. If you have to
(Continued)
CAUTION (Continued)
replace them, be sure to get
new original equipment wheel
bolts. Stop somewhere as
soon as you can and have the
bolts tightened with a torque
wrench to the proper torque
specication. SeeCapacities
and Specifications on
page 10-2for wheel bolt
torque specication.
Notice:Improperly tightened
wheel bolts can lead to brake
pulsation and rotor damage.
To avoid expensive brake repairs,
evenly tighten the wheel bolts
in the proper sequence and to
the proper torque specication.
SeeCapacities and Specifications
on page 10-2for the wheel bolt
torque specication.
Vehicle Service and Care 9-65
ProCarManuals.com

Towing
Towing Your Vehicle
The vehicle was neither designed
nor intended to be towed with any of
its wheels on the ground.
Consult your dealer/retailer or a
professional towing service if
the disabled vehicle needs to be
towed. SeeRoadside Assistance
Program on page 11-5.
Notice:Dolly towing or dinghy
towing your vehicle may
cause damage because of
reduced ground clearance.
Always put your vehicle on a
atbed truck.
Recreational Vehicle
Towing
Notice:Dolly towing or dinghy
towing your vehicle may
cause damage because of
reduced ground clearance.
Always put your vehicle on a
atbed trailer.
The vehicle was neither designed
nor intended to be towed with any
of its wheels on the ground.
Towing a Trailer
The vehicle is neither designed nor
intended to tow a trailer.
Appearance Care
Interior Cleaning
Your vehicle’s interior will continue
to look its best if it is cleaned
often. Although not always visible,
dust and dirt can accumulate
on your upholstery. Dirt can damage
carpet, fabric, leather, and plastic
surfaces. Regular vacuuming
is recommended to remove particles
from the upholstery. It is important
to keep your upholstery from
becoming and remaining heavily
soiled. Soils should be removed as
quickly as possible. Your vehicle’s
interior may experience extremes of
heat that could cause stains to
set rapidly.
Lighter colored interiors may require
more frequent cleaning. Use care
because newspapers and garments
that transfer color to your home
furnishings may also transfer color
to your vehicle’s interior.
9-72 Vehicle Service and Care
ProCarManuals.com

Fabric/Carpet
Use a vacuum cleaner with a soft
brush attachment frequently to
remove dust and loose dirt.
A canister vacuum with a beater bar
in the nozzle may only be used
on oor carpet and carpeted oor
mats. For soils, always try to remove
them rst with plain water or club
soda. Before cleaning, gently
remove as much of the soil as
possible using one of the following
techniques:
For liquids: gently blot the
remaining soil with a paper towel.
Allow the soil to absorb into
the paper towel until no more
can be removed.
For solid dry soils: remove as
much as possible and then
vacuum.To clean, use the following
instructions:
1. Saturate a lint-free, clean white
cloth with water or club soda.
2. Wring the cloth to remove excess
moisture.
3. Start on the outside edge of the
soil and gently rub toward the
center. Continue cleaning, using
a clean area of the cloth each
time it becomes soiled.
4. Continue to gently rub the soiled
area until the cleaning cloth
remains clean.
5. If the soil is not completely
removed, use a mild soap
solution and repeat the cleaning
process that was used with
plain water.
If any of the soil remains, a
commercial fabric cleaner or
spot lifter may be necessary.
When a commercial upholstery
cleaner or spot lifter is to be used,test a small hidden area for
colorfastness rst. If the locally
cleaned area gives any impression
that a ring formation may result,
clean the entire surface.
After the cleaning process has been
completed, a paper towel can be
used to blot excess moisture
from the fabric or carpet.
Leather
A soft cloth dampened with water
can be used to remove dust.
If a more thorough cleaning is
necessary, a soft cloth dampened
with a mild soap solution can be
used. Allow the leather to dry
naturally. Do not use heat to dry.
Never use steam to clean leather.
Never use spot lifters or spot
removers on leather. Many
commercial leather cleaners and
coatings that are sold to preserve
and protect leather may permanently
9-74 Vehicle Service and Care
ProCarManuals.com