2008 SATURN ASTRA light

Hazard Warning Flashers
|
:Press this button located on
the instrument panel, to make the
front and rear turn signal lamps ash
on and off. This warns others that
you are having trouble. Press the
button again to turn the ashers off.
While the hazard warning ashers
are on, the turn signals do not work.
An indicator light on the hazard
warning asher button comes on
whenever the ignition is turned on.
If the airbags are deployed, the
hazard warning ashers turn
on automatically. Press the
button twice to turn them off.
Horn
Press the horn symbol in the middle
of the steering wheel to sound
the horn.
Tilt Wheel
A tilt and telescope wheel lets the
steering wheel position be adjusted.
The adjustment lever is located on
the left side of the steering column.
It allows the steering column to be
moved up or down and in or out.
Do not adjust the steering wheel
while driving.
Turn Signal/Multifunction
Lever
The lever on the left side of the
steering column includes the
following:
G:Turn and Lane-Change
Signals.
2:Headlamp High/Low-Beam
Changer.
J:Cruise Control (If Equipped).
Flash-to-Pass Feature.
Information for these features is on
the pages following.
4-4 Instruments and Controls
ProCarManuals.com

Setting Cruise Control
For safety reasons the cruise
control cannot be turned on until
the brake has been applied once.
With automatic transmission, only
use cruise control in DRIVE (D).
Press the On/Off button to turn on
the cruise control. A message briey
appears on the instrument panel
cluster at the odometer display
when the cruise control has been
turned on.
{CAUTION
If you leave your cruise control
on when you are not using
cruise, you might hit a button
and go into cruise when you
do not want to. You could be
startled and even lose control.
Keep the cruise control switch
off until you want to use cruise
control.1. Press
Jand the current speed
is stored and maintained.
2. Take your foot off the accelerator
pedal. The
Jindicator light on
the instrument panel cluster turns
on after the cruise control has
been set to the desired speed.
The cruise control automatically
disengages under the following
conditions:
The vehicle speed drops below
25 mph (40 km/h).
The brake is applied.
The clutch pedal is applied
(for manual transmission
vehicles).
The automatic transmission is in
NEUTRAL (N).
The On/Off button is pressed.
CC On Message
CC Off Message
4-6 Instruments and Controls
ProCarManuals.com

Resuming a Set Speed
Once the vehicle speed reaches
about 25 mph (40 km/h) or more and
the cruise control is on, press
W.
The vehicle returns to the previous
speed selected before the cruise
was disengaged.
The stored speed is deleted if the
ignition is turned off.
Increasing Speed While Using
Cruise Control

Press and holdJuntil the
desired speed is reached,
then release it.
To increase vehicle speed
in small increments, briey
press
Jrepeatedly. Each
time this is done, the vehicle
speed increase by about 1 mph
(1.6 km/h) without using the
accelerator pedal.
When the
Jbutton is released
the current speed is stored
and maintained.
Reducing Speed While Using
Cruise Control

Press and holdWuntil the
desired lower speed is reached,
then release it.
To reduce vehicle speed in
small increments, briey
press
Wrepeatedly. Each time
this is done, the vehicle speed
decreases by about 1 mph
(1.6 km/h).
When the
Wbutton is released
the current speed is stored
and maintained.
Passing Another Vehicle
While Using Cruise Control
Use the accelerator pedal to
increase the vehicle speed. When
the accelerator pedal is released,
the vehicle will return to the
previously set cruise speed.
Using Cruise Control on Hills
How well the cruise control will work
on hills depends upon the vehicle
speed, load, and the steepness of
the hills. While going up steep hills,
you might have to step on the
accelerator pedal to maintain the
vehicle’s speed. While going
downhill, you might have to brake
or shift to a lower gear to keep the
vehicle’s speed down. Of course,
applying the brake turns off the
cruise control.
Ending Cruise Control
There are several ways to end
cruise control:
Step lightly on the brake or
clutch pedal.
The automatic transmission is
placed in NEUTRAL (N).
Press the9button.
Erasing Speed Memory
The cruise control set speed
memory is erased when the cruise
control or the ignition is turned off.
Instruments and Controls 4-7
ProCarManuals.com

Turn and Lane-Change
Signals
The turn signal has two upward and
downward positions to signal a turn
or a lane change.
To signal a turn, move the lever all
the way up or down, past the detent.
The lever returns to its starting
position when released.
An arrow on the instrument panel
cluster ashes in the direction of
the turn or lane change.To signal a lane change, raise or
lower the lever until the arrow starts
to ash, and then release the lever.
Do not move the lever past the
detent. The turn signal will
automatically ash three times
and turn off.
To cancel it before turning, move
the lever slightly in either direction.
Do not past the detent.
Headlamp High/
Low-Beam Changer
23
(Headlamp High/Low
Beam Changer):To change the
headlamps from low to high beam,
push the multifunction lever towards
the instrument panel. To return to
low-beam headlamps, push the lever
towards the instrument panel again
or pull the lever toward you. Then
release it.This indicator light on the instrument
panel cluster is on while the high
beam headlamps are on.
Flash-to-Pass
Pull the turn signal/multifunction
lever towards you to ash the high
beams from low beam.
4-8 Instruments and Controls
ProCarManuals.com

Notice:Adding any electrical
equipment to your vehicle
may damage it or keep other
components from working as they
should. The repairs would not be
covered by your warranty. Check
with your dealer/retailer before
adding electrical equipment.
When adding electrical equipment,
be sure to follow the installation
instructions included with the
equipment.
Notice:Improper use of the
power outlet can cause damage
not covered by your warranty.
Do not hang any type of
accessory or accessory bracket
from the plug because the
power outlets are designed for
accessory power plugs only.Warning Lights,
Gages, and Indicators
This section describes the warning
lights and gages on the vehicle.
Warning lights and gages can signal
that something is wrong before it
becomes serious enough to cause
an expensive repair or replacement.
Paying attention to the warning lights
and gages could prevent injury.
Warning lights come on when there
may be or is a problem with one
of the vehicle’s functions. Some
warning lights come on briey when
the engine is started to indicate they
are working.Gages can indicate when there may
be or is a problem with one of the
vehicle’s functions. Often gages
and warning lights work together
to indicate a problem with the
vehicle.
When one of the warning lights
comes on and stays on while
driving, or when one of the gages
shows there may be a problem,
check the section that explains
what to do. Follow this manual’s
advice. Waiting to do repairs can
be costly and even dangerous.
Instruments and Controls 4-11
ProCarManuals.com

Safety Belt Reminders
Driver Safety Belt Reminder
Light
There is a Driver Safety Belt
Reminder Light on the instrument
panel cluster.
When the engine is started this light
and chime will come on and stay on
for several seconds to remind people
to fasten their safety belts. The light
will also begin to ash.This cycle repeats if the driver
remains unbuckled and the vehicle
is moving.
If the driver’s belt is already buckled,
neither the light nor chime will
come on.
Passenger Safety Belt
Reminder Light
If your vehicle has this light, it will
operate the same as the Safety Belt
Reminder Light except that it is
meant for the front passenger.
If the passenger’s safety belt is
buckled, neither the chime nor the
light will come on.
Airbag Readiness Light
This light tells you if there is an
electrical problem. The system check
includes the airbag sensor, the
pretensioners, the airbag modules,
the wiring and the crash sensing
and diagnostic module. For more
information on the airbag system,
seeAirbag System on page 1-23.
This light will come on and stay
on for several seconds when you
start your vehicle. Then the light
should go out.
4-14 Instruments and Controls
ProCarManuals.com

If the airbag readiness light stays on
after you start the vehicle or comes
on when your are driving, your airbag
system may not work properly. Have
your vehicle serviced right away.
{CAUTION
If the airbag readiness light
stays on after the vehicle is
started, it means the airbag
system may not be working
properly. The airbags in the
vehicle may not inate in a
crash, or they could even
inate without a crash.
To help avoid injury, have the
vehicle serviced right away.
Passenger Airbag Status
Indicator
The vehicle has a passenger
sensing system. The rearview
mirror has a passenger airbag
status indicator.
When you start the vehicle, the
passenger airbag status indicator
will light ON and OFF, or the symbol
for on and off, for several seconds
as a system check. Then, after
several more seconds, the status
indicator will light either ON or OFF,
or either the on or off symbol to let
you know the status of the right
front passenger’s frontal and
seat-mounted side impact airbags. United States
Canada
Instruments and Controls 4-15
ProCarManuals.com

If, after several seconds, both status
indicator lights remain on, or if there
are no lights at all, there may be
a problem with the lights or the
passenger sensing system.
See your dealer/retailer for service.
{CAUTION
If the airbag readiness light in
the instrument panel cluster
ever comes on and stays on, it
means that something may be
wrong with the airbag system.
If this ever happens, have the
vehicle serviced promptly,
because an adult-size person
sitting in the right front
passenger’s seat may not have
the protection of the airbag(s).
SeeAirbag Readiness Light
on page 4-14for more on this,
including important safety
information.
Charging System Light
This light comes on briey when the
ignition is turned on, but the engine is
not running, as a check to show the
light is working. It should go out
when the engine is started.
If the light stays on, or comes
on while driving, there may be a
problem with the electrical charging
system. Have it checked by your
dealer/retailer. Driving while this
light is on could drain the battery.
If a short distance must be driven
with the light on, be sure to turn off
all accessories, such as the radio
and air conditioner.
Brake System Warning
Light
This light should come on briey
when the ignition is turned on.
If it does not come on, have it xed
so it will be ready to warn you if
there is a problem.
When the ignition is on, the brake
system warning light will come on
when the parking brake is set.
The light will stay on if the parking
brake does not release fully. If it
stays on after the parking brake is
fully released, there is a brake
problem. Have your brake system
inspected immediately.
United StatesCanada
Instruments and Controls 4-17
ProCarManuals.com