245 Car care and technical information
Waxing and polishingOther than in exceptional cases, do not use
abrasive polishes containing a cutting agent
on a new car. Always wash the car thor-
oughly before waxing or polishing.Engine compartmentClean the engine compartment using an
engine detergent and rinse with hot water.
Cover the headlights. Do not use high-pres-
sure washer. Avoid spraying the hood liner,
as this can become heavy and hang down
and touch the engine when the hood is
closed.
Do not use gasoline as a cleaning agent or
solvent when carrying out repairs or mainte-
nance. Saab recommends the use of envi-
ronmentally safe degreasing agents.
Touching up the paintDamaged paintwork should be treated as
soon as it is discovered: the longer it is left,
the greater the risk of corrosion. The
anti-perforation warranty does not cover
corrosion resulting from untreated defects.
Paintwork damage sustained in a crash is
usually extensive and can only be properly
restored by professionals.
However, you can repair small scratches
and stone-chip damage yourself. The nec-
essary tools and materials, such as primer,
touch-up paint and brushes, are available
from your Saab dealer.
In the case of minor flaws in the paintwork,
where the metal has not been exposed and
an undamaged layer of paint remains,
touch-up paint can usually be applied
directly, after any dirt has been scraped
away using a pointed knife.If corrosion has already set in, e.g. as a
result of stone-chip damage, use a pointed
knife to scrape off all surface rust. If possi-
ble, the damaged area should be taken
back to the bare metal. The metal should
then be primed with two thin coats of primer
applied by brush.
After the primer has dried, apply several thin
layers of topcoat enamel until the surface of
the repaired area is flush with the surround-
ing paintwork.
Stir both primer and touch-up enamel thor-
oughly before use and allow each coat to
dry before applying the next.
95_US_M08.book Page 245 Friday, May 11, 2007 1:06 PM
ProCarManuals.com
252 Car care and technical information5 Turn on the low beam headlights and
place a piece of cardboard or equivalent
(although not directly on the lens) in front
of the headlight not being aimed. This
should allow the beam cut-off of the
headlight being aimed to be seen on the
flat surface.
6 Turn the vertical aiming screw until the
horizontal cut-off of the headlight is
aligned with the horizontal line on the
wall.NOTEDo not cover a headlight directly on the
lens to improve beam cut-off when aim-
ing. Covering a headlight may cause
excessive heat build-up which may cause
damage to the headlight.
IB1951
Vertical aiming device
IB1952
Aiming marker on headlight lens
IB1953
Horizontal line on wall or other flat surface
IB1954
Correctly adjusted low beam
95_US_M08.book Page 252 Friday, May 11, 2007 1:06 PM
ProCarManuals.com
274 IndexCruise control
__________________ 159
Cup holder
____________________ 128
Dampers
______________________ 269
Date
_________________________ 105
Date code, tires
_________________ 233
DDate display
___________________ 105
DICE/TWICE ___________________ 217
Definitions and terminology, tire
____ 231
Determining correct load, tires
_____ 233
Dim-dipped beam
________________ 73
Direction indicators _______________ 75
Diversity antenna
_______________ 109
Door handles
___________________ 44
Door mirrors
___________________ 116
Doors, locks & luggage compartment
_43
Drive belt
______________________ 267
Drive belt, alternator
_____________ 201
Drive belts, length
_______________ 267
Driver’s seat, programmable
________ 20
Driving at night
_________________ 181
Driving in hot weather
____________ 173
Driving with a load
______________ 181
EEDR (Event Data Recorders)
______ 259
ESP
® _________________________ 163
Electrical system, technical data
____ 267Electric heating of rear seat
________ 87
Electric windows
________________ 115
Electronic Stability Program
_______ 163
Electronic starting interlock _________ 49
Emergency operation of moonroof
__ 124
Emission control systems
_________ 192
Engine bay
____________________ 191
Engine bay, cleaning
_____________ 245
Engine number
_________________ 272
Engine oil, grade ________________ 265
Engine, description ______________ 194
Engine, technical data ____________ 264
Engine, temperature gauge
________ 65
Engine-oil level, checking
_________ 194
Error codes, Audio System ________ 112
Event Data Recorders (EDR) ______ 259
Expansion tank, coolant
__________ 195
FFilling a portable fuel container
_____ 148
Flat spots, tires
_________________ 224
Fluid level, automatic transmission
__ 195
Folding the parcel shelf,
9-5 SportCombi
________________ 133
Folding the rear seat, 9-5 Sedan
___ 129
Folding the rear seat, 9-5 SportCombi
132
Frequency band
_________________ 93
Frequently asked questions on airbag
40
Front fog lights
__________________ 76
Frost warning
___________________ 68Fuel
__________________________ 146
Fuel consumption
________________ 68
Fuel container
__________________ 148
Fuel gauge
_____________________ 65
Fuel grade _____________________ 264
Fuel information
_________________ 148
Fuse box under hood
____________ 220
Fuse panel
_____________________ 216
Fuses
_________________________ 216
GGarage door opener
_____________ 118
Gearbox number
________________ 272
Gearbox oil, checking
____________ 195
Gearbox, technical data, __________ 268
General functions
_______________ 105
Glove compartment ______________ 126
HHandbrake
_____________________ 165
Hazard warning lights
_____________ 76
Head restraint
___________________ 21
Headlight flasher _________________ 73
Headlights
______________________ 73
Heated front seats
________________ 87
Hood
_________________________ 190
Horn __________________________ 114
95_US_M08.book Page 274 Friday, May 11, 2007 1:06 PM
ProCarManuals.com
